I am in the process of upgrading to -current to take advantage of the MP
code.  I used build.sh to compile the kernel and userland into the obj/
directory, then ran "./build.sh install=/".

Fortunately the new kernel boots, but unfortunately it puts me in single
user mode after complaining about file system problems.  The old kernel
boots up just fine, however.

Any suggestions would be greatly appreciated.  Below are the error message
and dmesg output from the 1.6.1 kernel.

Thanks
-Nathan

---- error message after kenel loads ----

swapctl: /dev/sd2b: Device not configured
Starting file system checks:
Can't open /dev/rsd2a: Device not configured
CAN'T CHECK FILE SYSTEM.
/dev/rsd2a: UNEXPECTED INCONSISTENCY; RUN fsck_ffs MANUALLY.
Automatic file system check failed; help!
init: /bin/sh on /etc/rc terminiated abnormally, going to single user
mode.

---- dmesg output from 1.6.1 kernel ----
NetBSD 1.6.1 (GENERIC) #0: Tue Apr  8 12:05:52 UTC 2003

autobuild@tgm.daemon.org:/autobuild/netbsd-1-6/i386/OBJ/autobuild/netbsd-1-6/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) (686-class), 728.47 MHz
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 2-way
cpu0: L2 cache 256 KB 32b/line 8-way
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
total memory = 511 MB
avail memory = 467 MB
using 6144 buffers containing 26276 KB of memory
BIOS32 rev. 0 found at 0xffe90
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82840 Host (rev. 0x01)
pchb0: random number generator enabled
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: Intel 82840 AGP (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Nvidia Corporation Quadro (rev. 0x10)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
ppb1 at pci0 dev 30 function 0: Intel 82801AA Hub-to-PCI Bridge (rev.
0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
ex0 at pci2 dev 4 function 0: 3Com 3c905C-TX 10/100 Ethernet with mngmt
(rev. 0x78)
ex0: interrupting at irq 9
ex0: MAC address 00:b0:d0:3e:60:04
bmtphy0 at ex0 phy 24: Broadcom 3c905C internal PHY, rev. 7
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
clcs0 at pci2 dev 6 function 0: Cirrus Logic CS4280 CrystalClear Audio
Interface (rev. 0x01)
clcs0: interrupting at irq 10
clcs0: CRY20 codec; headphone, 20 bit DAC, 18 bit ADC, Crystal Semi 3D
audio0 at clcs0: full duplex, independent
midi0 at clcs0: CS4280 MIDI UART
Texas Instruments TSB12LV23 OHCI IEEE 1394 Host Controller (Firewire
serial bus, interface 0x10) at pci2 dev 11 function 0 not configured
ppb2 at pci2 dev 14 function 0: Digital Equipment DECchip 21152 PCI-PCI
Bridge (rev. 0x03)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
ahc1 at pci3 dev 10 function 0
ahc1: interrupting at irq 10
ahc1: aic7899 Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ahc2 at pci3 dev 10 function 1
ahc2: interrupting at irq 14
ahc2: aic7899 Wide Channel B, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc2: 16 targets, 8 luns per target
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801AA LPC Interface Bridge (rev. 0x02)
pciide0 at pci0 dev 31 function 1: Intel 82801AA IDE Controller (ICH)
(rev. 0x02)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0: primary channel ignored (disabled)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <CRD-8482B, , 1.05> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
sd0 at atapibus0 drive 1: <IOMEGA  ZIP 250       ATAPI, , 51.G> type 0
direct removable
sd0: drive offline
sd0: 32-bit data port
sd0: drive supports PIO mode 3
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)
sd0(pciide0:1:1): using PIO mode 3
uhci0 at pci0 dev 31 function 2: Intel 82801AA USB Controller (rev. 0x02)
uhci0: interrupting at irq 14
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82801AA SMBus Controller (SMBus serial bus, revision 0x02) at pci0
dev 31 function 3 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask ed65 netmask ef65 ttymask ffe7
scsibus0: waiting 2 seconds for devices to settle...
sd1 at scsibus0 target 0 lun 0: <QUANTUM, VIKING II 4.5WLS, 3506> SCSI2
0/direct fixed
sd1: 4350 MB, 8338 cyl, 5 head, 213 sec, 512 bytes/sect x 8910423 sectors
sd1: sync (25.0ns offset 31), 16-bit (80.000MB/s) transfers, tagged
queueing
sd2 at scsibus0 target 2 lun 0: <SEAGATE, ST39103LW, 3700> SCSI2 0/direct
fixed
sd2: 8683 MB, 9772 cyl, 6 head, 303 sec, 512 bytes/sect x 17783240 sectors
sd2: sync (25.0ns offset 15), 16-bit (80.000MB/s) transfers, tagged
queueing
sd3 at scsibus0 target 4 lun 0: <SEAGATE, ST39102LW, 0005> SCSI2 0/direct
fixed
sd3: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240
sectors
sd3: sync (25.0ns offset 15), 16-bit (80.000MB/s) transfers, tagged
queueing
scsibus1: waiting 2 seconds for devices to settle...
Kernelized RAIDframe activated
pciide0:1:1: pio setting rejected, falling back to PIO mode 0
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)
sd0(pciide0:1:1): using PIO mode 0
sd1: no disk label
sd3: no disk label
sd1: no disk label
sd3: no disk label
boot device: sd2
root on sd2a dumps on sd2b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)