5.0_RC3 messed up RTL8111DL onboard NIC

To: current-users%netbsd.org@localhost
Subject: 5.0_RC3 messed up RTL8111DL onboard NIC
From: Thomas Bieg <tomsbsd%googlemail.com@localhost>
Date: Fri, 10 Apr 2009 20:08:14 +0200
(I hope current-users fits the bill here.)

Booting the amd64 installation CD from
ftp://ftp.netbsd.org/pub/NetBSD-daily/netbsd-5/200904070000Z/iso/amd64cd.iso
on an ASRock X58 SuperComputer (Core i7 920) with dual Realtek RTL8111DL 
onboard NICs
and trying to auto-configure re0 using DHCP via the installer menu resulted in 
(at the
very least) botched MAC addresses. (Though it worked as far as obtaining an IP 
address.)


ifconfig shows (copied one cold-start later):

re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx>
        enabled=0
        address: ff:ff:ff:ff:ff:ff
        media: Ethernet autoselect (100baseTX full-duplex)
        status: active
re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx>
        enabled=0
        address: 39:a0:60:ad:52:15
        media: Ethernet autoselect (none)
        status: no carrier

(Notice that re1's MAC isn't real either and that re0 is connected to a GigE 
switch.)


This has happened before but I wasn't sure that it was NetBSD's fault then and 
I was able
revive the NIC by reentering the MAC address in the Windows driver's extended 
properties.

This time I am sure to blame NetBSD and though I managed to revive the NIC 
again, the
situation seemed worse than before with Windows initally saying it's unable to 
start the
device.

I am willing to provide further information but please understand that I'm not 
too keen
on playing Russian roulette with this not-too-cheap system.

Full dmesg (minus some USB devices) below.


Tom



Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0_RC3 (INSTALL) #0: Tue Apr  7 17:08:13 UTC 2009
        
builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5/amd64/200904070000Z-obj/home/builds/ab/netbsd-5/src/sys/arch/amd64/compile/INSTALL
total memory = 12286 MB
avail memory = 11893 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.5 @ 0xfce70 (31 entries)
To Be Filled By O.E.M. To Be Filled By O.E.M. (To Be Filled By O.E.M.)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2678MHz, id 0x106a4
cpu1 at mainbus0 apid 2: Intel 686-class, 2678MHz, id 0x106a4
cpu2 at mainbus0 apid 4: Intel 686-class, 2678MHz, id 0x106a4
cpu3 at mainbus0 apid 6: Intel 686-class, 2678MHz, id 0x106a4
cpu4 at mainbus0 apid 1: Intel 686-class, 2678MHz, id 0x106a4
cpu5 at mainbus0 apid 3: Intel 686-class, 2678MHz, id 0x106a4
cpu6 at mainbus0 apid 5: Intel 686-class, 2678MHz, id 0x106a4
cpu7 at mainbus0 apid 7: Intel 686-class, 2678MHz, id 0x106a4
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <031709,RSDT2121,20090317>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
FDC (PNP0700) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
FWH (INT0800) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F03): aux port
pckbc2: irq 12
UAR1 (PNP0501) at acpi0 not configured
WMI1 (pnp0c14) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x3405 (rev. 0x12)
ppb0 at pci0 dev 3 function 0: vendor 0x8086 product 0x340a (rev. 0x12)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 7
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x1002 product 0x9440 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
azalia0 at pci1 dev 0 function 1: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17
azalia0: host: 0x1002/0xaa30 (rev. 0), HDA rev. 1.0
ppb1 at pci0 dev 7 function 0: vendor 0x8086 product 0x340e (rev. 0x12)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 6
pci2: no spaces enabled!
vendor 0x8086 product 0x342e (interrupt system, revision 0x12) at pci0 dev 20 
function 0 not configured
vendor 0x8086 product 0x3422 (interrupt system, revision 0x12) at pci0 dev 20 
function 1 not configured
vendor 0x8086 product 0x3423 (interrupt system, revision 0x12) at pci0 dev 20 
function 2 not configured
vendor 0x8086 product 0x3438 (interrupt system, revision 0x12) at pci0 dev 20 
function 3 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3a37 (rev. 0x00)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x3a38 (rev. 0x00)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x3a39 (rev. 0x00)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x3a3c (rev. 0x00)
ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
azalia1 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia1: interrupting at ioapic0 pin 22
azalia1: host: 0x8086/0x3a3e (rev. 0), HDA rev. 1.0
ppb2 at pci0 dev 28 function 0: vendor 0x8086 product 0x3a40 (rev. 0x00)
pci3 at ppb2 bus 4
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
jmide0 at pci3 dev 0 function 0: vendor 0x197b product 0x2363
jmide0: 1 PATA port, 2 SATA ports
jmide0: interrupting at ioapic0 pin 16
jmide0: can't map ahci registers
jmide0: PCI IDE interface used
jmide0: bus-master DMA support present
jmide0: primary channel wired to native-PCI mode
jmide0: primary channel is SATA
atabus0 at jmide0 channel 0
jmide0: secondary channel wired to native-PCI mode
jmide0: secondary channel is SATA
atabus1 at jmide0 channel 1
ppb3 at pci0 dev 28 function 1: vendor 0x8086 product 0x3a42 (rev. 0x00)
pci4 at ppb3 bus 3
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
fwohci0 at pci4 dev 0 function 0: vendor 0x1106 product 0x3403 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 17
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 xx:xx:xx:xx:xx:xx:xx:xx
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
pciide0 at pci4 dev 0 function 1
pciide0: vendor 0x1106 product 0x0415 (rev. 0xa0)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel wired to native-PCI mode
pciide0: using ioapic0 pin 17 for native-PCI interrupt
atabus2 at pciide0 channel 0
pciide0: secondary channel wired to native-PCI mode
atabus3 at pciide0 channel 1
ppb4 at pci0 dev 28 function 2: vendor 0x8086 product 0x3a44 (rev. 0x00)
pci5 at ppb4 bus 2
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci5 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet (rev. 
0x03)
re0: interrupting at ioapic0 pin 18
re0: Unknown revision (0x28000000)
re0: Ethernet address ff:ff:ff:ff:ff:ff
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb5 at pci0 dev 28 function 5: vendor 0x8086 product 0x3a4a (rev. 0x00)
pci6 at ppb5 bus 1
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
re1 at pci6 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet (rev. 
0x03)
re1: interrupting at ioapic0 pin 17
re1: Unknown revision (0x28000000)
re1: Ethernet address 39:a0:60:ad:52:15
re1: using 256 tx descriptors
rgephy1 at re1 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x3a34 (rev. 0x00)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x3a35 (rev. 0x00)
uhci4: interrupting at ioapic0 pin 19
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x3a36 (rev. 0x00)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x3a3a (rev. 0x00)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb6 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x90)
pci7 at ppb6 bus 5
pci7: i/o space, memory space enabled
vendor 0x13d0 product 0x2103 (miscellaneous network, revision 0x01) at pci7 dev 
2 function 0 not configured
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x3a16 (rev. 0x00)
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x3a22
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: AHCI revision 1.2, 6 ports, 32 command slots, features 0xef20e0e0
atabus4 at ahcisata0 channel 0
atabus5 at ahcisata0 channel 1
atabus6 at ahcisata0 channel 2
atabus7 at ahcisata0 channel 3
atabus8 at ahcisata0 channel 4
atabus9 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x3a30 (rev. 0x00)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2678857160 Hz quality 3000
azalia0: codec[0]: ATI R600 HDMI (rev. 1.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
azalia1: codec[0]: Realtek ALC885 (rev. 1.1), HDA rev. 1.0
audio1 at azalia1: full duplex, independent
uhub0 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 6 ports with 6 removable, self powered
uhub1 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
uhub7 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub7: 2 ports with 2 removable, self powered
ahcisata0 port 1: device present, speed: 3.0Gb/s
ahcisata0 port 3: device present, speed: 1.5Gb/s
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 2: device present, speed: 1.5Gb/s
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
wd0 at atabus4 drive 0: <WDC WD10EADS-00L5B1>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
wd1 at atabus5 drive 0: <WDC WD10EADS-00L5B1>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
atapibus0 at atabus6: 1 targets
cd0 at atapibus0 drive 0: <HL-DT-ST BDDVDRW GGC-H20L, , 1.03> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
cd0(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
atapibus1 at atabus7: 1 targets
cd1 at atapibus1 drive 0: <TSSTcorpDVD-ROM SH-D163B, , SB03> cdrom removable
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1(ahcisata0:3:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) 
(using DMA)
Kernelized RAIDframe activated
md0: internal 5000 KB image area
boot device: cd0
root on md0a dumps on md0b
root file system type: ffs
WARNING: clock gained 2 days
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
Follow-Ups:
- Re: 5.0_RC3 messed up RTL8111DL onboard NIC
  - From: Izumi Tsutsui
Prev by Date: fatal page fault in supervisor mode during reboot
Next by Date: Re: state or future of LFS?
Previous by Thread: fatal page fault in supervisor mode during reboot
Next by Thread: Re: 5.0_RC3 messed up RTL8111DL onboard NIC
Indexes:
Home | Main Index | Thread Index | Old Index