Re: kernel hangs immediately after loading

[Klaus Heinz <k.heinz.okt.vier%onlinehome.de@localhost>]

Back in March I wrote:

> I just cross-built a kernel (-current sources about a week old) and tried to
> boot this from a floppy. This is what I see with the serial console:
> 
>   >> NetBSD/bebox BOOT, Revision 1.5
>   >> (heinz@silence, Sun Mar 21 18:15:11 MET 2004)
>   >> Memory: 98304 k
> 
>   Boot: Loading in()
>   2853792+169964 [86480+72406]=0x3092e8
>   start=0x3100
> 
> No more output.

I have now been able to create a boot floppy with a GENERIC kernel from
NetBSD 2.0 which prints the configuration output again.

Unfortunately, it does not work with the old IDE drive I have in the box
(see attached console output).

Can anyone repeat this problem with the boot floppy (console at serial1,
9600 bps, just write the image to /dev/fd0a with dd)

  http://www.NetBSD.org/~heinz/serial_boot_floppy2_0.img

?

ciao
     Klaus

>> NetBSD/bebox BOOT, Revision 1.5
>> (heinz@silence, Sun Oct 17 08:30:20 MEST 2004)
>> Memory: 98304 k

Boot: Loading in()
2295896+284064 [124704+113718]=0x2b0404
start=0x3100

Loaded initial symtab at 0x278ef8, strtab at 0x2978cc, # entries 7782
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 2.0_RC4 (GENERIC) #19: Sun Oct 17 10:15:55 MEST 2004
        heinz@silence:/var/tmp2/src-2.0/obj.bebox/sys/arch/bebox/compile/GENERIC
total memory = 98304 KB
avail memory = 92200 KB
mainbus0 (root)
cpu0 at mainbus0: 603 (Revision 3.2), ID 0 (primary)
cpu0: HID0 90d000<DOZE,DPM,ICE,DCE,DLOCK>
pci0 at mainbus0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Motorola MPC105 "Eagle" Host Bridge (rev. 0x24)
pcib0 at pci0 dev 11 function 0
pcib0: Intel 82378ZB System I/O (SIO) (rev. 0x43)
Symbios Logic 53c810 (SCSI mass storage, revision 0x02) at pci0 dev 12 function 
0 not configured
Digital Equipment DECchip 21142/21143 10/100 Ethernet (ethernet network, 
revision 0x21) at pci0 dev 14 function 0 not configured
pfb0 at pci0 dev 15 function 0isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atabus0 at wdc0 channel 0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
biomask 4040 netmask 4040 ttymask 40c2
fd0 at fdc0 drive 1: 1.44MB, 80 cyl, 2 head, 18 sec
raidattach: Asked for 8 units
Kernelized RAIDframe activated
wd0 at atabus0 drive 0wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
: <Conner Peripherals 635MB - CFS635A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 609 MB, 1238 cyl, 16 head, 63 sec, 512 bytes/sect x 1248438 sectors
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0: drive supports PIO mode 4, DMA mode 2
Searching for RAID components...
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0)
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wdc0:0:0: lost interrupt
        type: ata tc_bcount: 512 tc_skip: 0
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0)
wd0: dos partition I/O error
boot device: <unknown>
root device: