Re: HEAD UP acpi/mpbios/ioapic support commited

[Pierrick Brossin <pierrick%bs-network.net@localhost>]

On Mon, Oct 02, 2006 at 09:14:40PM +0200, Manuel Bouyer wrote:
> Then I don't know why it finds only one CPU. Can you post the dmesg ?

Sure. Here you go.


-Pierrick Brossin

0: pin 16 attached to pci0 device 3 INT_A (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 3 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci0 device 3 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 31 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci0 device 31 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 31 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 23 attached to pci0 device 29 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 26 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 22 attached to pci0 device 27 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci0 device 28 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci0 device 28 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 28 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci0 device 28 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 20 attached to pci0 device 25 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 21 attached to pci0 device 25 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci0 device 29 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci0 device 29 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci0 device 29 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci0 device 26 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci0 device 26 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci1 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci1 device 0 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci1 device 0 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci1 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 21 attached to pci5 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 22 attached to pci5 device 0 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 23 attached to pci5 device 0 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 20 attached to pci5 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 22 attached to pci5 device 1 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 23 attached to pci5 device 1 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 20 attached to pci5 device 1 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 21 attached to pci5 device 1 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 23 attached to pci5 device 2 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 20 attached to pci5 device 2 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 21 attached to pci5 device 2 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 22 attached to pci5 device 2 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci4 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci4 device 0 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci4 device 0 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci4 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci3 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci3 device 0 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci3 device 0 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci3 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 16 attached to pci2 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 17 attached to pci2 device 0 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 18 attached to pci2 device 0 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: pin 19 attached to pci2 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int9 189a9<vector=a9,delmode=1,logical,level,masked,dest=0> 
3000000<target=3>
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0A08 [PCI Express/PCI-X Mode-2 Host Bridge] at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
PNP0100 [AT Timer] at acpi0 not configured
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
PNP0800 [AT-style speaker sound] at acpi0 not configured
PNP0C04 [Math Coprocessor] at acpi0 not configured
PNP0501 [16550A-compatible COM port] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
ATK0110 at acpi0 not configured
PNP0401 [ECP printer port] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C-170): ACPI Power Button
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
pci0 at hypervisor0 bus 0: configuration mode 1hypervisor0: added to list as 
bus 0

pci0: i/o space, memory space enabled
pci0: can't establish powerhook
pchb0 at pci0 dev 0 function 0
pchb0: Intel product 0x29a0 (rev. 0x02)
ppb0 at pci0 dev 1 function 0: Intel product 0x29a1 (rev. 0x02)
pci1 at ppb0 bus 1ppb0: added to list as bus 1

pci1: i/o space, memory space enabled
pci1: can't establish powerhook
vga0 at pci1 dev 0 function 0: NVIDIA product 0x01df (rev. 0xa1)
vga0: WARNING: ignoring 64-bit BAR @ 0x14
vga0: WARNING: ignoring 64-bit BAR @ 0x1c
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 1-3 added (80x25, vt100 emulation)
uhci0 at pci0 dev 26 function 0: Intel 82801H USB UHCI Controller (rev. 0x02)
ioapic0: int16 1a9b1<vector=b1,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
uhci0: interrupting at ioapic0 pin 16, event channel 3
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 26 function 1: Intel 82801H USB UHCI Controller (rev. 0x02)
ioapic0: int17 1a9b9<vector=b9,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
uhci1: interrupting at ioapic0 pin 17, event channel 4
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 26 function 7: Intel 82801H USB EHCI Controller (rev. 0x02)
ioapic0: int18 1a9c1<vector=c1,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
ehci0: interrupting at ioapic0 pin 18, event channel 5
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
Intel 82801H High Definition Audio Controller (multimedia subclass 0x03, 
revision 0x02) at pci0 dev 27 function 0 not configured
ppb1 at pci0 dev 28 function 0: Intel 82801H PCI Express Port #1 (rev. 0x02)
pci2 at ppb1 bus 4ppb1: added to list as bus 4

pci2: memory space enabled
pci2: can't establish powerhook
ppb2 at pci0 dev 28 function 3: Intel 82801H PCI Express Port #4 (rev. 0x02)
pci3 at ppb2 bus 3ppb2: added to list as bus 3

pci3: i/o space, memory space enabled
pci3: can't establish powerhook
re0 at pci3 dev 0 function 0: RealTek 8168B/8111B Gigabit Ethernet
ioapic0: int19 1a9c9<vector=c9,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
re0: interrupting at ioapic0 pin 19, event channel 6
re0: eeprom autoload timed out
re0: Ethernet address 00:17:31:85:2c:e3
re0: using 256 tx descriptors
ukphy0 at re0 phy 7: Generic IEEE 802.3u media interface
ukphy0: RTL8169S/8110S 1000BASE-T media interface (OUI 0x00e04c, model 0x0011), 
rev. 2
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb3 at pci0 dev 28 function 4: Intel 82801H PCI Express Port #5 (rev. 0x02)
pci4 at ppb3 bus 2ppb3: added to list as bus 2

pci4: i/o space, memory space enabled
pci4: can't establish powerhook
pciide0 at pci4 dev 0 function 0
pciide0: unknown vendor 0x197b product 0x2363 (rev. 0x02)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel wired to native-PCI mode
pciide0: using ioapic0 pin 16, event channel 3 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel wired to native-PCI mode
atabus1 at pciide0 channel 1
uhci2 at pci0 dev 29 function 0: Intel 82801H USB UHCI Controller (rev. 0x02)
ioapic0: int23 1a9d1<vector=d1,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
uhci2: interrupting at ioapic0 pin 23, event channel 7
usb3 at uhci2: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 1: Intel 82801H USB UHCI Controller (rev. 0x02)
uhci3: interrupting at ioapic0 pin 19, event channel 6
usb4 at uhci3: USB revision 1.0
uhub4 at usb4
uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhci4 at pci0 dev 29 function 2: Intel 82801H USB UHCI Controller (rev. 0x02)
uhci4: interrupting at ioapic0 pin 18, event channel 5
usb5 at uhci4: USB revision 1.0
uhub5 at usb5
uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
ehci1 at pci0 dev 29 function 7: Intel 82801H USB EHCI Controller (rev. 0x02)
ehci1: interrupting at ioapic0 pin 23, event channel 7
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3 uhci4
usb6 at ehci1: USB revision 2.0
uhub6 at usb6
uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
ppb4 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xf2)
pci5 at ppb4 bus 5ppb4: added to list as bus 5

pci5: i/o space enabled
pci5: can't establish powerhook
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801H LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801H Serial ATA Controller (ICH8) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 19, event channel 6 for native-PCI interrupt
atabus2 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus3 at piixide0 channel 1
Intel 82801H SMBus Controller (SMBus serial bus, revision 0x02) at pci0 dev 31 
function 3 not configured
piixide1 at pci0 dev 31 function 5
piixide1: Intel 82801H Serial ATA Controller (ICH8) (rev. 0x02)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 19, event channel 6 for native-PCI interrupt
atabus4 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus5 at piixide1 channel 1
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
pckbc0 at isa0 port 0x60-0x64
pckbdprobe: reset error 5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsprobe: reset error 5
Xen clock: using event channel 10
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
raidattach: Asked for 8 units
Kernelized RAIDframe activated
xenbus0: using event channel 11
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <LITE-ON DVDRW SHM-165H6S, , HS07> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
ehci1: handing over low speed device on port 1 to uhci2
uhub6: port 1, device disappeared after reset
ehci1: handing over low speed device on port 2 to uhci2
uhub6: port 2, device disappeared after reset
ehci1: handing over full speed device on port 4 to uhci3
uhub6: port 4, device disappeared after reset
uhidev0 at uhub3 port 1 configuration 1 interface 0
uhidev0: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub3 port 1 configuration 1 interface 1
uhidev1: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 buttons and Z dir.
wsmouse0 at ums0 mux 0
wd0 at atabus2 drive 0: <WDC WD3200KS-00PFB0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Searching for RAID components...
boot device: wd0
root on wd0a dumps on wd0b
umass0 at uhub4 port 2 configuration 1 interface 0mountroot: trying lfs...
mountroot: trying ffs...
root file system type: ffs

umass0: ----- Ltd. SPRING-Rev1.1, rev 1.10/0.12, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 4 luns per target
init: copying out path `/sbin/init' 11
sd0 at scsibus0 target 0 lun 0: <SPRING, MultiCard Slot A, 0100> disk removable
uhidev2 at uhub3 port 2 configuration 1 interface 0sd0: 977 MB, 49671 cyl, 16 
head, 63 sec, 512 bytes/sect x 2001888 sectors

uhidev2: Logitech USB-PS/2 Optical Mouse, rev 2.00/13.00, addr 3, iclass 3/1
sd1 at scsibus0 target 0 lun 1: <SPRING, MultiCard Slot D, 0100> disk removable
sd1: drive offline
ums1 at uhidev2: 4 buttons and Z dir.
wsmouse1 at ums1 mux 0
sd2 at scsibus0 target 0 lun 2: <SPRING, MultiCard Slot S, 0100> disk removable
sd2: drive offline
sd3 at scsibus0 target 0 lun 3: <SPRING, MultiCard Slot M, 0100> disk removable
sd3: drive offline
wsdisplay0: screen 4 added (80x25, vt100 emulation)