Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.

To: Manuel Bouyer <bouyer%antioche.eu.org@localhost>
Subject: Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
From: "Marcin M. Jessa" <lists%yazzy.org@localhost>
Date: Fri, 26 Mar 2010 11:26:34 +0100

On 03/26/2010 11:22 AM, Manuel Bouyer wrote:

Can you send the dmesg of this kernel which finds all the drives ?

Output of dmesg's attached.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0.2 (XEN3_DOM0) #0: Sat Feb  6 13:44:13 UTC 2010
        
builds%b8.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-2-RELEASE/amd64/201002061851Z-obj/home/builds/ab/netbsd-5-0-2-RELEASE/src/sys/arch/amd64/compile/XEN3_DOM0
total memory = 1024 MB
avail memory = 974 MB
timecounter: Timecounters tick every 10.000 msec
SMBIOS rev. 2.34 @ 0xfbf7c000 (33 entries)
mainbus0 (root)
mainbus0: scanning 0x98c00 to 0x98ff0 for MP signature
mainbus0: scanning 0x98800 to 0x98bf0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xf77c0
mainbus0: MP config table at 0x9bb20, 340 bytes long
ACPI Error (tbxfroot-0308): A valid RSDP was not found [20080321]
ACPI: unable to initialize ACPI tables: AE_NOT_FOUND
mainbus0: Intel MP Specification (Version 1.4) (AMD      HAMMER      )
cpu0 at mainbus0 apid 0: (boot processor)
cpu1 at mainbus0 apid 1: (application processor)
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type PCI   
mpbios: bus 4 is type ISA   
ioapic0 at mainbus0 apid 2: pa 0xfec00000, virtual wire mode, version 11, 24 
pins
ioapic1 at mainbus0 apid 3: pa 0xfc000000, virtual wire mode, version 11, 4 pins
ioapic2 at mainbus0 apid 4: pa 0xfc001000, virtual wire mode, version 11, 4 pins
ioapic0: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int1 attached to isa0 irq 1 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int2 attached to isa0 irq 0 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int3 attached to isa0 irq 3 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int4 attached to isa0 irq 4 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int5 attached to isa0 irq 5 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int6 attached to isa0 irq 6 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int7 attached to isa0 irq 7 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int8 attached to isa0 irq 8 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int9 attached to isa0 irq 9 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int10 attached to isa0 irq 10 (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: int11 attached to isa0 irq 11 (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: int12 attached to isa0 irq 12 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int13 attached to isa0 irq 13 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int14 attached to isa0 irq 14 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int15 attached to isa0 irq 15 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int19 attached to pci1 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int19 attached to pci1 device 0 INT_D (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int18 attached to pci1 device 6 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic1: int3 attached to pci2 device 3 INT_A (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic1: int3 attached to pci2 device 4 INT_A (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic2: int2 attached to pci3 device 2 INT_A (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
local apic: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
local apic: int1 attached to NMI (type 1<type=1=NMI> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
mainbus0: MP WARNING: 104 bytes of extended entries not examined
hypervisor0 at mainbus0: Xen version 3.1
vcpu0 at hypervisor0: AMD 686-class, 2004MHz, id 0xf58
debug virtual interrupt using event channel 1
xenbus0 at hypervisor0: Xen Virtual Bus Interface
xencons0 at hypervisor0: Xen Virtual Console Driver
pci0 at hypervisor0 bus 0: configuration mode 1
hypervisor0: added to list as bus 0
pci0: i/o space, memory space enabled
ppb0 at pci0 dev 6 function 0: vendor 0x1022 product 0x7460 (rev. 0x07)
pci1 at ppb0 bus 1
ppb0: added to list as bus 1
pci1: i/o space, memory space enabled
ohci0 at pci1 dev 0 function 0: vendor 0x1022 product 0x7464 (rev. 0x0b)
ioapic0: int19 1a9c0<vector=c0,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
ohci0: interrupting at ioapic0 pin 19, event channel 2
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci1 dev 0 function 1: vendor 0x1022 product 0x7464 (rev. 0x0b)
ohci1: interrupting at ioapic0 pin 19, event channel 2
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
vga0 at pci1 dev 6 function 0: vendor 0x1002 product 0x4752 (rev. 0x27)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x1022 product 0x7468 (rev. 0x05)
viaide0 at pci0 dev 7 function 1
viaide0: Advanced Micro Devices AMD8111 IDE Controller (rev. 0x03)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
ioapic0: int14 9c8<vector=c8,delmode=1,logical,dest=0> 3000000<target=3>
viaide0: primary channel interrupting at ioapic0 pin 14, event channel 3
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
ioapic0: int15 9d0<vector=d0,delmode=1,logical,dest=0> 3000000<target=3>
viaide0: secondary channel interrupting at ioapic0 pin 15, event channel 4
atabus1 at viaide0 channel 1
amdpm0 at pci0 dev 7 function 3: vendor 0x1022 product 0x746b (rev. 0x05)
timecounter: Timecounter "amdpm0" frequency 3579545 Hz quality 1000
amdpm0: 24-bit timer
iic at amdpm0 not configured
amdpm0: random number generator enabled (apprx. 41ms)
ppb1 at pci0 dev 10 function 0: vendor 0x1022 product 0x7450 (rev. 0x12)
pci2 at ppb1 bus 2
ppb1: added to list as bus 2
pci2: i/o space, memory space enabled
bge0 at pci2 dev 3 function 0: Broadcom BCM5702X Gigabit Ethernet
ioapic1: int3 1a9d8<vector=d8,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
bge0: interrupting at ioapic1 pin 3, event channel 5
bge0: ASIC BCM5703 A2 (0x1002), Ethernet address 00:50:45:00:b1:d7
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge1 at pci2 dev 4 function 0: Broadcom BCM5702X Gigabit Ethernet
bge1: interrupting at ioapic1 pin 3, event channel 5
bge1: ASIC BCM5703 A2 (0x1002), Ethernet address 00:50:45:00:b1:d8
brgphy1 at bge1 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
vendor 0x1022 product 0x7451 (interrupt system, interface 0x10, revision 0x01) 
at pci0 dev 10 function 1 not configured
ppb2 at pci0 dev 11 function 0: vendor 0x1022 product 0x7450 (rev. 0x12)
pci3 at ppb2 bus 3
ppb2: added to list as bus 3
pci3: i/o space, memory space enabled
satalink0 at pci3 dev 2 function 0
satalink0: Silicon Image SATALink 3114 (rev. 0x02)
satalink0: 33MHz PCI bus
satalink0: bus-master DMA support present
ioapic2: int2 1a921<vector=21,delmode=1,logical,actlo,level,masked,dest=0> 
3000000<target=3>
satalink0: using ioapic2 pin 2, event channel 6 for native-PCI interrupt
atabus2 at satalink0 channel 0
atabus3 at satalink0 channel 1
atabus4 at satalink0 channel 2
atabus5 at satalink0 channel 3
vendor 0x1022 product 0x7451 (interrupt system, interface 0x10, revision 0x01) 
at pci0 dev 11 function 1 not configured
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3
pchb3: vendor 0x1022 product 0x1103 (rev. 0x00)
pchb4 at pci0 dev 25 function 0
pchb4: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb5 at pci0 dev 25 function 1
pchb5: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb6 at pci0 dev 25 function 2
pchb6: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb7 at pci0 dev 25 function 3
pchb7: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
ioapic0: int7 929<vector=29,delmode=1,logical,dest=0> 3000000<target=3>
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
ioapic0: int3 931<vector=31,delmode=1,logical,dest=0> 3000000<target=3>
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
ioapic0: int1 939<vector=39,delmode=1,logical,dest=0> 3000000<target=3>
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsprobe: reset error 5
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
Xen clock: using event channel 10
timecounter: Timecounter "xen_system_time" frequency 1000000000 Hz quality 10000
xenbus0: using event channel 11
satalink0: port 1: device present, speed: 1.5Gb/s
satalink0: port 2: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0: <WDC WD5000AAKB-00H8A0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
uhub0 at usb0: vendor 0x1022 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1022 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1 at atabus0 drive 1: <WDC WD5000AAKB-00H8A0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Western Digital External HDD, rev 2.00/1.07, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <WD, 2500JB External, 0107> disk fixed
sd0: fabricating a geometry
sd0: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
umass1 at uhub1 port 2 configuration 1 interface 0
umass1: Western Digital External HDD, rev 2.00/1.07, addr 3
umass1: using SCSI over Bulk-Only
scsibus1 at umass1: 2 targets, 1 lun per target
sd1 at scsibus1 target 0 lun 0: <WD, 2500JB External, 0107> disk fixed
sd1: fabricating a geometry
sd1: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
wd2 at atabus1 drive 0: <ST3500630A>
wd2: quirks 2<FORCE_LBA48>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd2(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd3 at atabus3 drive 0: <SAMSUNG HD321KJ>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd3: 32-bit data port
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd3(satalink0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd4 at atabus4 drive 0: <SAMSUNG HD321KJ>
wd4: drive supports 16-sector PIO transfers, LBA48 addressing
wd4: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd4: 32-bit data port
wd4: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd4(satalink0:2:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
raidattach: Asked for 8 units
Kernelized RAIDframe activated
Searching for RAID components...
Component on: wd0a: 976773105
   Row: 0 Column: 1 Num Rows: 1 Num Columns: 2
   Version: 2 Serial Number: 1603201001 Mod Counter: 522
   Clean: No Status: 0
   sectPerSU: 128 SUsPerPU: 1 SUsPerRU: 1
   RAID Level: 1  blocksize: 512 numBlocks: 976772992
   Autoconfig: Yes
   Contains root partition: Yes
   Last configured as: raid0
Component on: wd1a: 976773105
   Row: 0 Column: 0 Num Rows: 1 Num Columns: 2
   Version: 2 Serial Number: 1603201001 Mod Counter: 522
   Clean: No Status: 0
   sectPerSU: 128 SUsPerPU: 1 SUsPerRU: 1
   RAID Level: 1  blocksize: 512 numBlocks: 976772992
   Autoconfig: Yes
   Contains root partition: Yes
   Last configured as: raid0
sd0: fabricating a geometry
sd1: fabricating a geometry
Component on: wd4a: 625142385
   Row: 0 Column: 1 Num Rows: 1 Num Columns: 2
   Version: 2 Serial Number: 2008062601 Mod Counter: 1443
   Clean: No Status: 0
   sectPerSU: 128 SUsPerPU: 1 SUsPerRU: 1
   RAID Level: 1  blocksize: 512 numBlocks: 625142272
   Autoconfig: Yes
   Contains root partition: No
   Last configured as: raid2
Found: wd1a at 0
Found: wd0a at 1
RAID autoconfigure
Configuring raid0:
Starting autoconfiguration of RAID set...
Looking for 0 in autoconfig
Found: wd1a at 0
Looking for 1 in autoconfig
Found: wd0a at 1
raid0: allocating 20 buffers of 65536 bytes.
raid0: RAID Level 1
raid0: Components: /dev/wd1a /dev/wd0a
raid0: Total Sectors: 976772992 (476939 MB)
raid0: configured ok
Found: wd4a at 1
RAID autoconfigure
Configuring raid2:
Starting autoconfiguration of RAID set...
Looking for 0 in autoconfig
Looking for 1 in autoconfig
Found: wd4a at 1
raid2: allocating 20 buffers of 65536 bytes.
raid2: RAID Level 1
raid2: Components: component0[**FAILED**] /dev/wd4a
raid2: Total Sectors: 625142272 (305245 MB)
raid2: configured ok
boot device: raid0
root on raid0a dumps on raid0b
mountroot: trying lfs...
mountroot: trying ffs...
root file system type: ffs
init: copying out path `/sbin/init' 11
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

Follow-Ups:
- Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
  - From: Manuel Bouyer

References:
- Dom0 with enabled ACPI doesn't recognize my IDE drives.
  - From: Marcin M. Jessa
- Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
  - From: Manuel Bouyer

Prev by Date: Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
Next by Date: Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
Previous by Thread: Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
Next by Thread: Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.
Indexes:

Home | Main Index | Thread Index | Old Index