Hello there! I've been expanding storage in my Xen VM server. My motherboard has two SATA controllers, one with six ports and another with two; the six ports are all taken so I attached two disks to the two ports on the so-far-unused controller. However, my aging NetBSD 7.0.1 dom0 kernel couldn't seem to talk to the disks - it saw them but complained that IDENTIFY failed. The dom0 was well overdue an upgrade, so I booted 9.0 from a USB stick and was pleased to see that it could see the disks fine, so I did a NetBSD install onto one of the disks with a GENERIC kernel, rebooted into it, built Xen and set it all up, rebooted into Xen... and the disks couldn't IDENTIFY again. Hmmm. Presumably, this is either: 1) Something caused by Xen itself acting as a hypervisor (but I'm not sure how that could be). 2) Some difference between the SATA drivers compiled into the GENERIC vs. DOM0 kernels. Presuming the latter, I tried comparing the kernel config files for the two, but it's hard to see the wood for the trees - there's a lot of differences that seem unrelated to running as a dom0 kernel, like the same lines being present but in a different order. I grepped out the lines about ahci and sata and they looked equivalent to my untrained eye... Does anybody have any hints as to what the difference might be? Or could tell me what the minimal changes I'd need to make to the GENERIC config file to turn it into a DOM0 one would be, so I can try that out? Or should I just buy a PCI card with a different SATA controller on and see if that works out of the box with the DOM0 kernel? That's my last resort, as if the GENERIC kernel can talk to that disk, surely DOM0 should be able to as well and it's just some software toggle somewhere :-) Here's my dmesg when failing to identify the disks under DOM0, wd0 and wd1 are the drives that fail to configure (in this case I actually booted the kernel and Xen from wd0 at the boot prompt, but the kernel can't see it so it attaches to wd2 as the root filesystem, which is my old NetBSD 7.0.1 install), in case anyone's interested: [ 1.0000000] mainbus0 (root) [ 1.0000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) [ 1.0000000] ACPI: XSDT 0x00000000BA1C3080 00007C (v01 ALASKA A M I 01072009 AMI 00010013) [ 1.0000000] ACPI: FACP 0x00000000BA1CF080 00010C (v05 ALASKA A M I 01072009 AMI 00010013) [ 1.0000000] ACPI: DSDT 0x00000000BA1C3190 00BEF0 (v02 ALASKA A M I 000000F9 INTL 20091112) [ 1.0000000] ACPI: FACS 0x00000000BA1EB080 000040 [ 1.0000000] ACPI: APIC 0x00000000BA1CF190 000072 (v03 ALASKA A M I 01072009 AMI 00010013) [ 1.0000000] ACPI: FPDT 0x00000000BA1CF208 000044 (v01 ALASKA A M I 01072009 AMI 00010013) [ 1.0000000] ACPI: SSDT 0x00000000BA1CF250 000539 (v01 PmRef Cpu0Ist 00003000 INTL 20051117) [ 1.0000000] ACPI: SSDT 0x00000000BA1CF790 000AD8 (v01 PmRef CpuPm 00003000 INTL 20051117) [ 1.0000000] ACPI: MCFG 0x00000000BA1D0268 00003C (v01 01072009 MSFT 00000097) [ 1.0000000] ACPI: HPET 0x00000000BA1D02A8 000038 (v01 ALASKA A M I 01072009 AMI. 00000005) [ 1.0000000] ACPI: SSDT 0x00000000BA1D02E0 00036D (v01 SataRe SataTabl 00001000 INTL 20091112) [ 1.0000000] ACPI: SSDT 0x00000000BA1D0650 003299 (v01 SaSsdt SaSsdt 00003000 INTL 20091112) [ 1.0000000] ACPI: RMAD 0x00000000BA1D38F0 0000B8 (v01 INTEL HSW 00000001 INTL 00000001) [ 1.0000000] ACPI: MATS 0x00000000BA1D39A8 000034 (v02 ALASKA A M I 00000002 w?x2 00000000) [ 1.0000000] ACPI: 5 ACPI AML tables successfully acquired and loaded [ 1.0000000] ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins [ 1.0000000] cpu0 at mainbus0 apid 0 [ 1.0000000] cpu1 at mainbus0 apid 2 [ 1.0000000] cpu2 at mainbus0 apid 4 [ 1.0000000] cpu3 at mainbus0 apid 6 [ 1.0000000] hypervisor0 at mainbus0: Xen version 4.8.5nb0 [ 1.0000000] hypervisor0: features: pae_pgdir_above_4gb mmu_pt_update_preserve_ad highmem_assist gnttab_map_avail_bits [ 1.0000000] VIRQ_DEBUG interrupt using event channel 1 [ 1.0000000] vcpu0 at hypervisor0 [ 1.0000000] vcpu0: Intel(R) Core(TM) i5-4460 CPU @ 3.20GHz, id 0x306c3 [ 1.0000000] vcpu0: package 0, core 0, smt 0 [ 1.0000000] xenbus0 at hypervisor0: Xen Virtual Bus Interface [ 1.0000000] xencons0 at hypervisor0: Xen Virtual Console Driver [ 1.0000000] acpi0 at hypervisor0: Intel ACPICA 20190405 [ 1.0000000] acpi0: X/RSDT: OemId <ALASKA, A M I,01072009>, AslId <AMI ,00010013> [ 1.0000000] mpacpi: PCI bus 5 int routing already done! [ 1.0000000] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f8000000 [ 1.0000000] acpi0: SCI interrupting at int 9 [ 1.0000000] acpi0: fixed power button present [ 1.0000000] timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900 [ 1.0000030] acpiec0 at acpi0 (H_EC, PNP0C09-1)acpiec0: autoconfiguration error: unable to evaluate _GPE: AE_NOT_FOUND [ 1.0000030] TPMX (PNP0C01) at acpi0 not configured [ 1.0000030] FWHD (INT0800) at acpi0 not configured [ 1.0000030] HPET (PNP0103) at acpi0 not configured [ 1.0000030] LDRC (PNP0C02) at acpi0 not configured [ 1.0000030] TIMR (PNP0100) at acpi0 not configured [ 1.0000030] CWDT (INT3F0D) at acpi0 not configured [ 1.0000030] SIO1 (PNP0C02) at acpi0 not configured [ 1.0000030] UAR1 (PNP0501) at acpi0 not configured [ 1.0000030] RMSC (PNP0C02) at acpi0 not configured [ 1.0000030] PDRC (PNP0C02) at acpi0 not configured [ 1.0000030] WMI1 (PNP0C14) at acpi0 not configured [ 1.0000030] acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button [ 1.0000030] PTMD (INT3394) at acpi0 not configured [ 1.0000030] FAN0 (PNP0C0B) at acpi0 not configured [ 1.0000030] FAN1 (PNP0C0B) at acpi0 not configured [ 1.0000030] FAN2 (PNP0C0B) at acpi0 not configured [ 1.0000030] FAN3 (PNP0C0B) at acpi0 not configured [ 1.0000030] FAN4 (PNP0C0B) at acpi0 not configured [ 1.0000030] acpitz0 at acpi0 (TZ00) [ 1.0000030] acpitz0: active cooling level 0: 80.0C [ 1.0000030] acpitz0: active cooling level 1: 55.0C [ 1.0000030] acpitz0: active cooling level 2: 0.0C [ 1.0000030] acpitz0: active cooling level 3: 0.0C [ 1.0000030] acpitz0: active cooling level 4: 0.0C [ 1.0000030] acpitz0: levels: critical 105.0 C [ 1.0000030] acpitz1 at acpi0 (TZ01) [ 1.0000030] acpitz1: levels: critical 105.0 C, passive 108.0 C, passive cooling [ 1.0000030] ACPI: Enabled 4 GPEs in block 00 to 3F [ 1.0000030] pci0 at hypervisor0 bus 0: configuration mode 1 [ 1.0000030] pci0: i/o space, memory space enabled [ 1.0000030] pchb0 at pci0 dev 0 function 0: vendor 8086 product 0c00 (rev. 0x06) [ 1.0000030] vga0 at pci0 dev 2 function 0: vendor 8086 product 0412 (rev. 0x06) [ 1.0000030] wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation) [ 1.0000030] wsmux1: connecting to wsdisplay0 [ 1.0000030] drm at vga0 not configured [ 1.0000030] hdaudio0 at pci0 dev 3 function 0: HD Audio Controller [ 1.0000030] hdaudio0: interrupting at ioapic0 pin 16 [ 1.0000030] hdaudio0: autoconfiguration error: RIRB timeout [ 1.0000030] hdaudio0: autoconfiguration error: RIRB timeout [ 1.0000030] xhci0 at pci0 dev 20 function 0: vendor 8086 product 8c31 (rev. 0x04) [ 1.0000030] xhci0: interrupting at ioapic0 pin 16 [ 1.0000030] xhci0: xHCI version 1.0 [ 1.0000030] usb0 at xhci0: USB revision 3.0 [ 1.0000030] usb1 at xhci0: USB revision 2.0 [ 1.0000030] vendor 8086 product 8c3a (miscellaneous communications, revision 0x04) at pci0 dev 22 function 0 not configured [ 1.0000030] wm0 at pci0 dev 25 function 0: I217 V Ethernet Connection (rev. 0x04) [ 1.0000030] wm0: interrupting at ioapic0 pin 20 [ 1.0000030] wm0: PCI-Express bus [ 1.0000030] wm0: 2048 words FLASH, version 0.13.4 [ 1.0000030] wm0: Ethernet address 94:de:80:7c:e7:91 [ 1.0000030] wm0: 0x6a4480<FLASH,IOH_VALID,PCIE,ASF_FIRM,AMT,WOL,EEE> [ 1.0000030] ihphy0 at wm0 phy 2: i217 10/100/1000 media interface, rev. 4 [ 1.0000030] ihphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.0000030] ehci0 at pci0 dev 26 function 0: vendor 8086 product 8c2d (rev. 0x04) [ 1.0000030] ehci0: interrupting at ioapic0 pin 16 [ 1.0000030] ehci0: BIOS has given up ownership [ 1.0000030] ehci0: EHCI version 1.0 [ 1.0000030] usb2 at ehci0: USB revision 2.0 [ 1.0000030] hdaudio1 at pci0 dev 27 function 0: HD Audio Controller [ 1.0000030] hdaudio1: interrupting at ioapic0 pin 22 [ 1.0000030] hdafg0 at hdaudio1: vendor 10ec product 0899 [ 1.0000030] hdafg0: DAC00 8ch: Speaker [Jack] [ 1.0000030] hdafg0: DAC01 2ch: HP Out [Jack] [ 1.0000030] hdafg0: DIG02 2ch: SPDIF Out [Built-In] [ 1.0000030] hdafg0: DIG03 2ch: SPDIF Out [Jack] [ 1.0000030] hdafg0: ADC04 2ch: Line In [Jack], Mic In [Jack] [ 1.0000030] hdafg0: ADC05 2ch: Mic In [Jack] [ 1.0000030] hdafg0: DIG-In06 2ch: SPDIF In [Built-In] [ 1.0000030] hdafg0: 8ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3 [ 1.0000030] audio0 at hdafg0: playback, capture, full duplex, independent [ 1.0000030] audio0: slinear_le:16 8ch 48000Hz, blk 40ms for playback [ 1.0000030] audio0: slinear_le:16 2ch 48000Hz, blk 40ms for recording [ 1.0000030] spkr0 at audio0: PC Speaker (synthesized) [ 1.0000030] wsbell at spkr0 not configured [ 1.0000030] ppb0 at pci0 dev 28 function 0: vendor 8086 product 8c10 (rev. 0xd4) [ 1.0000030] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s [ 1.0000030] pci1 at ppb0 bus 1 [ 1.0000030] pci1: i/o space, memory space enabled [ 1.0000030] ppb1 at pci0 dev 28 function 2: vendor 8086 product 8c14 (rev. 0xd4) [ 1.0000030] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s [ 1.0000030] ppb1: link is x1 @ 2.5GT/s [ 1.0000030] pci2 at ppb1 bus 2 [ 1.0000030] pci2: i/o space, memory space enabled [ 1.0000030] re0 at pci2 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x06) [ 1.0000030] re0: interrupting at ioapic0 pin 18 [ 1.0000030] re0: Ethernet address e8:de:27:06:b4:8b [ 1.0000030] re0: using 256 tx descriptors [ 1.0000030] rgephy0 at re0 phy 7: RTL8211D 1000BASE-T media interface [ 1.0000030] rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.0000030] ppb2 at pci0 dev 28 function 3: vendor 8086 product 8c16 (rev. 0xd4) [ 1.0000030] ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s [ 1.0000030] ppb2: link is x1 @ 2.5GT/s [ 1.0000030] pci3 at ppb2 bus 3 [ 1.0000030] pci3: i/o space, memory space enabled [ 1.0000030] re1 at pci3 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x06) [ 1.0000030] re1: interrupting at ioapic0 pin 19 [ 1.0000030] re1: Ethernet address 14:cc:20:00:4f:c3 [ 1.0000030] re1: using 256 tx descriptors [ 1.0000030] rgephy1 at re1 phy 7: RTL8211D 1000BASE-T media interface [ 1.0000030] rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.0000030] ppb3 at pci0 dev 28 function 4: vendor 8086 product 244e (rev. 0xd4) [ 1.0000030] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s [ 1.0000030] ppb3: link is x1 @ 2.5GT/s [ 1.0000030] pci4 at ppb3 bus 4 [ 1.0000030] pci4: i/o space, memory space enabled [ 1.0000030] ppb4 at pci4 dev 0 function 0: vendor 8086 product 244e (rev. 0x41) [ 1.0000030] pci5 at ppb4 bus 5 [ 1.0000030] pci5: i/o space, memory space enabled [ 1.0000030] ppb5 at pci0 dev 28 function 5: vendor 8086 product 8c1a (rev. 0xd4) [ 1.0000030] ppb5: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s [ 1.0000030] pci6 at ppb5 bus 6 [ 1.0000030] pci6: i/o space, memory space enabled [ 1.0000030] ahcisata0 at pci6 dev 0 function 0: vendor 1b4b product 9172 (rev. 0x11) [ 1.0000030] ahcisata0: 64-bit DMA [ 1.0000030] ahcisata0: AHCI revision 1.0, 2 ports, 32 slots, CAP 0xe237ff21<SXS,PSC,SSC,PMD,FBSS,SPM,SAM,ISS=0x3=Gen3,SAL,SSNTF,SNCQ,S64A> [ 1.0000030] ahcisata0: interrupting at ioapic0 pin 17 [ 1.0000030] atabus0 at ahcisata0 channel 0 [ 1.0000030] atabus1 at ahcisata0 channel 1 [ 1.0000030] ehci1 at pci0 dev 29 function 0: vendor 8086 product 8c26 (rev. 0x04) [ 1.0000030] ehci1: interrupting at ioapic0 pin 23 [ 1.0000030] ehci1: BIOS has given up ownership [ 1.0000030] ehci1: EHCI version 1.0 [ 1.0000030] usb3 at ehci1: USB revision 2.0 [ 1.0000030] ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 8c44 (rev. 0x04) [ 1.0000030] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000 [ 1.0000030] ichlpcib0: 24-bit timer [ 1.0000030] ahcisata1 at pci0 dev 31 function 2: vendor 8086 product 8c02 (rev. 0x04) [ 1.0000030] ahcisata1: 64-bit DMA [ 1.0000030] ahcisata1: AHCI revision 1.30, 6 ports, 32 slots, CAP 0xc330ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SNCQ,S64A> [ 1.0000030] ahcisata1: interrupting at ioapic0 pin 19 [ 1.0000030] atabus2 at ahcisata1 channel 0 [ 1.0000030] atabus3 at ahcisata1 channel 1 [ 1.0000030] atabus4 at ahcisata1 channel 2 [ 1.0000030] atabus5 at ahcisata1 channel 3 [ 1.0000030] atabus6 at ahcisata1 channel 4 [ 1.0000030] atabus7 at ahcisata1 channel 5 [ 1.0000030] ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 8c22 (rev. 0x04) [ 1.0000030] ichsmb0: interrupting at ioapic0 pin 18 [ 1.0000030] iic0 at ichsmb0: I2C bus [ 1.0000030] isa0 at ichlpcib0 [ 1.0000030] pckbc0 at isa0 port 0x60-0x64 [ 1.0000030] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 [ 1.0000030] timecounter: Timecounter "xen_system_time" frequency 1000000000 Hz quality 10000 [ 1.0000030] Xen vcpu0 clock: using event channel 10 [ 1.0000030] xenbus0: using event channel 11 [ 1.0000030] uhub0 at usb0: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 3.00/1.00, addr 0 [ 1.0000030] uhub0: 6 ports with 6 removable, self powered [ 1.0000030] uhub1 at usb1: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 0 [ 1.0000030] uhub1: 14 ports with 14 removable, self powered [ 1.0000030] IPsec: Initialized Security Association Processing. [ 1.0200300] uhub2 at usb2: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1 [ 1.0200300] uhub2: 2 ports with 2 removable, self powered [ 1.0200300] uhub3 at usb3: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1 [ 1.0200300] uhub3: 2 ports with 2 removable, self powered [ 1.1000439] ahcisata0 port 0: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata0 port 1: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 0: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 1: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 2: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 3: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 4: device present, speed: 6.0Gb/s [ 1.1000439] ahcisata1 port 5: device present, speed: 6.0Gb/s [ 2.6300436] wd0 at atabus0 drive 0 [ 2.6300436] uhub4 at uhub1 port 9: vendor 045b (0x45b) product 0209 (0x209), class 9/0, rev 2.10/1.00, addr 2 [ 2.6300436] uhub4: single transaction translator [ 2.6300436] uhub5 at uhub0 port 5: vendor 045b (0x45b) product 0210 (0x210), class 9/0, rev 3.00/1.00, addr 1 [ 2.6300436] uhub4: 4 ports with 4 removable, self powered [ 2.6300436] uhub5: 4 ports with 4 removable, self powered [ 3.1600436] wd0: autoconfiguration error: IDENTIFY failed [ 3.1600436] wd0(ahcisata0:0:0): using PIO mode 0 [ 3.1600436] wd1 at atabus1 drive 0 [ 3.2700451] uhub6 at uhub2 port 1: vendor 8087 (0x8087) product 8008 (0x8008), class 9/0, rev 2.00/0.04, addr 2 [ 3.2700451] uhub6: single transaction translator [ 3.2700451] uhub7 at uhub3 port 1: vendor 8087 (0x8087) product 8000 (0x8000), class 9/0, rev 2.00/0.04, addr 2 [ 3.2700451] uhub7: single transaction translator [ 3.2700451] uhub6: 6 ports with 6 removable, self powered [ 3.2700451] uhub7: 8 ports with 8 removable, self powered [ 3.7700440] wd1: autoconfiguration error: IDENTIFY failed [ 3.7700440] wd1(ahcisata0:1:0): using PIO mode 0 [ 3.7700440] wd2 at atabus2 drive 0 [ 3.7700440] wd2: <ST2000DM001-1ER164> [ 3.7700440] wd2: drive supports 16-sector PIO transfers, LBA48 addressing [ 3.7700440] wd2: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 3.8200439] wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) [ 3.8200439] wd2(ahcisata1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) [ 3.8200439] wd3 at atabus3 drive 0 [ 3.8200439] wd3: <ST2000DM001-1ER164> [ 3.8200439] wd3: drive supports 16-sector PIO transfers, LBA48 addressing [ 3.8200439] wd3: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 3.8700439] wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) [ 3.8700439] wd3(ahcisata1:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) [ 3.8700439] wd4 at atabus4 drive 0 [ 3.8700439] wd4: <ST2000DM001-1ER164> [ 3.8700439] wd4: drive supports 16-sector PIO transfers, LBA48 addressing [ 3.8700439] wd4: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 3.8800302] uhub8 at uhub1 port 10: vendor 045b (0x45b) product 0209 (0x209), class 9/0, rev 2.10/1.00, addr 3 [ 3.8800302] uhub8: single transaction translator [ 3.8800302] uhub9 at uhub0 port 6: vendor 045b (0x45b) product 0210 (0x210), class 9/0, rev 3.00/1.00, addr 4 [ 3.8800302] uhub8: 4 ports with 4 removable, self powered [ 3.8800302] uhub9: 4 ports with 4 removable, self powered [ 3.9100440] wd4: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) [ 3.9100440] wd4(ahcisata1:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) [ 3.9100440] wd5 at atabus5 drive 0 [ 3.9100440] wd5: <ST2000DM001-1ER164> [ 3.9100440] wd5: drive supports 16-sector PIO transfers, LBA48 addressing [ 3.9100440] wd5: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 3.9600441] wd5: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) [ 3.9700324] wd5(ahcisata1:3:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) [ 3.9700324] wd6 at atabus6 drive 0 [ 3.9700324] wd6: <WDC WD20EFRX-68EUZN0> [ 3.9700324] wd6: drive supports 16-sector PIO transfers, LBA48 addressing [ 3.9700324] wd6: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 4.0100440] wd6: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), NCQ (32 tags) w/PRIO [ 4.0100440] wd6(ahcisata1:4:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO [ 4.0100440] wd7 at atabus7 drive 0 [ 4.0100440] wd7: <WDC WD20EFRX-68EUZN0> [ 4.0100440] wd7: drive supports 16-sector PIO transfers, LBA48 addressing [ 4.0100440] wd7: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors [ 4.0600441] wd7: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), NCQ (32 tags) w/PRIO [ 4.0600441] wd7(ahcisata1:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO [ 4.8700440] uhub10 at uhub8 port 2: vendor 0424 (0x424) product 2524 (0x2524), class 9/0, rev 2.00/0.00, addr 5 [ 4.8700440] uhub10: multiple transaction translators [ 4.8700440] uhub10: 4 ports with 2 removable, self powered [ 5.8600440] uhidev0 at uhub10 port 1 configuration 1 interface 0 [ 5.8600440] uhidev0: Belkin Corporation (0x50d) Flip CC (0x3201), rev 1.10/2.34, addr 6, iclass 3/1 [ 5.8700317] uhidev0: 2 report ids [ 5.8700317] uhid0 at uhidev0 reportid 1: input=1, output=1, feature=0 [ 5.8700317] uhid1 at uhidev0 reportid 2: input=1, output=0, feature=0 [ 6.5300215] uhidev1 at uhub10 port 3 configuration 1 interface 0 [ 6.5300215] uhidev1: Primax (0x47d) Kensington Eagle Trackball (0x2048), rev 2.00/6.00, addr 7, iclass 3/1 [ 6.5300215] ums0 at uhidev1: 3 buttons, W and Z dirs [ 6.5300215] wsmouse0 at ums0 mux 0 [ 7.1800441] uhidev2 at uhub10 port 4 configuration 1 interface 0 [ 7.1800441] uhidev2: vendor 0430 (0x430) product 0005 (0x05), rev 1.00/1.01, addr 8, iclass 3/1 [ 7.1800441] ukbd0 at uhidev2 [ 7.5900419] wskbd0 at ukbd0: console keyboard, using wsdisplay0 [ 7.5900419] WARNING: 5 errors while detecting hardware; check system log. [ 7.5900419] boot device: wd2 [ 7.5900419] root on wd2a dumps on wd2b [ 7.5900419] Your machine does not initialize mem_clusters; sparse_dumps disabled [ 7.6200436] root file system type: ffs [ 7.6200436] kern.module.path=/stand/amd64-xen/9.0/modules Thanks, -- Alaric Snell-Pym (M7KIT) http://www.snell-pym.org.uk/alaric/
Attachment:
signature.asc
Description: OpenPGP digital signature