Source-Changes-HG archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
[src/trunk]: src/sys/dev/mii - All of Marvell PHY's registers from addr 0x0 t...
details: https://anonhg.NetBSD.org/src/rev/61938b678016
branches: trunk
changeset: 323513:61938b678016
user: msaitoh <msaitoh%NetBSD.org@localhost>
date: Mon Jun 18 09:12:17 2018 +0000
description:
- All of Marvell PHY's registers from addr 0x0 to 0xf conforms IEEE 802.3
specification, so those register definitions are not required. Use mii.h's
definitions. Note that E1000_ER_PAR_DETECT_FAULT should be 0x0010 instead of
0x0100(typo).
- Restore code for BMCR_ISO which was removed in makphy.c rev. 1.44
- Whitespace fix.
diffstat:
sys/dev/mii/e1000phyreg.h | 141 +---------------------------------------------
sys/dev/mii/makphy.c | 46 ++++++++------
2 files changed, 29 insertions(+), 158 deletions(-)
diffs (280 lines):
diff -r 3926a2d9bd53 -r 61938b678016 sys/dev/mii/e1000phyreg.h
--- a/sys/dev/mii/e1000phyreg.h Mon Jun 18 09:11:03 2018 +0000
+++ b/sys/dev/mii/e1000phyreg.h Mon Jun 18 09:12:17 2018 +0000
@@ -1,4 +1,4 @@
-/* $NetBSD: e1000phyreg.h,v 1.1 2018/06/16 17:44:53 jdolecek Exp $ */
+/* $NetBSD: e1000phyreg.h,v 1.2 2018/06/18 09:12:17 msaitoh Exp $ */
/* $FreeBSD: head/sys/dev/mii/e1000phyreg.h 326022 2017-11-20 19:36:21Z pfg $ */
/*-
* Principal Author: Parag Patel
@@ -73,147 +73,12 @@
#define E1000_MAX_REG_ADDRESS 0x1F
-#define E1000_CR 0x00 /* control register */
-#define E1000_CR_SPEED_SELECT_MSB 0x0040
-#define E1000_CR_COLL_TEST_ENABLE 0x0080
-#define E1000_CR_FULL_DUPLEX 0x0100
-#define E1000_CR_RESTART_AUTO_NEG 0x0200
-#define E1000_CR_ISOLATE 0x0400
-#define E1000_CR_POWER_DOWN 0x0800
-#define E1000_CR_AUTO_NEG_ENABLE 0x1000
-#define E1000_CR_SPEED_SELECT_LSB 0x2000
-#define E1000_CR_LOOPBACK 0x4000
-#define E1000_CR_RESET 0x8000
-
-#define E1000_CR_SPEED_1000 0x0040
-#define E1000_CR_SPEED_100 0x2000
-#define E1000_CR_SPEED_10 0x0000
-
-#define E1000_SR 0x01 /* status register */
-#define E1000_SR_EXTENDED 0x0001
-#define E1000_SR_JABBER_DETECT 0x0002
-#define E1000_SR_LINK_STATUS 0x0004
-#define E1000_SR_AUTO_NEG 0x0008
-#define E1000_SR_REMOTE_FAULT 0x0010
-#define E1000_SR_AUTO_NEG_COMPLETE 0x0020
-#define E1000_SR_PREAMBLE_SUPPRESS 0x0040
-#define E1000_SR_EXTENDED_STATUS 0x0100
-#define E1000_SR_100T2 0x0200
-#define E1000_SR_100T2_FD 0x0400
-#define E1000_SR_10T 0x0800
-#define E1000_SR_10T_FD 0x1000
-#define E1000_SR_100TX 0x2000
-#define E1000_SR_100TX_FD 0x4000
-#define E1000_SR_100T4 0x8000
-
-#define E1000_ID1 0x02 /* ID register 1 */
-#define E1000_ID2 0x03 /* ID register 2 */
-#define E1000_ID_88E1000 0x01410C50
-#define E1000_ID_88E1000S 0x01410C40
-#define E1000_ID_88E1011 0x01410C20
-#define E1000_ID_MASK 0xFFFFFFF0
-
-#define E1000_AR 0x04 /* autonegotiation advertise reg */
-#define E1000_AR_SELECTOR_FIELD 0x0001
-#define E1000_AR_10T 0x0020
-#define E1000_AR_10T_FD 0x0040
-#define E1000_AR_100TX 0x0080
-#define E1000_AR_100TX_FD 0x0100
-#define E1000_AR_100T4 0x0200
-#define E1000_AR_PAUSE 0x0400
-#define E1000_AR_ASM_DIR 0x0800
-#define E1000_AR_REMOTE_FAULT 0x2000
-#define E1000_AR_NEXT_PAGE 0x8000
-#define E1000_AR_SPEED_MASK 0x01E0
-
-/* Autonegotiation register bits for fiber cards (Alaska Only!) */
-#define E1000_FA_1000X_FD 0x0020
-#define E1000_FA_1000X 0x0040
-#define E1000_FA_SYM_PAUSE 0x0080
-#define E1000_FA_ASYM_PAUSE 0x0100
-#define E1000_FA_FAULT1 0x1000
-#define E1000_FA_FAULT2 0x2000
-#define E1000_FA_NEXT_PAGE 0x8000
-
-#define E1000_LPAR 0x05 /* autoneg link partner abilities reg */
-#define E1000_LPAR_SELECTOR_FIELD 0x0001
-#define E1000_LPAR_10T 0x0020
-#define E1000_LPAR_10T_FD 0x0040
-#define E1000_LPAR_100TX 0x0080
-#define E1000_LPAR_100TX_FD 0x0100
-#define E1000_LPAR_100T4 0x0200
-#define E1000_LPAR_PAUSE 0x0400
-#define E1000_LPAR_ASM_DIR 0x0800
-#define E1000_LPAR_REMOTE_FAULT 0x2000
-#define E1000_LPAR_ACKNOWLEDGE 0x4000
-#define E1000_LPAR_NEXT_PAGE 0x8000
-
-/* autoneg link partner ability register bits for fiber cards (Alaska Only!) */
-#define E1000_FPAR_1000X_FD 0x0020
-#define E1000_FPAR_1000X 0x0040
-#define E1000_FPAR_SYM_PAUSE 0x0080
-#define E1000_FPAR_ASYM_PAUSE 0x0100
-#define E1000_FPAR_FAULT1 0x1000
-#define E1000_FPAR_FAULT2 0x2000
-#define E1000_FPAR_ACK 0x4000
-#define E1000_FPAR_NEXT_PAGE 0x8000
-
-#define E1000_ER 0x06 /* autoneg expansion reg */
-#define E1000_ER_LP_NWAY 0x0001
-#define E1000_ER_PAGE_RXD 0x0002
-#define E1000_ER_NEXT_PAGE 0x0004
-#define E1000_ER_LP_NEXT_PAGE 0x0008
-#define E1000_ER_PAR_DETECT_FAULT 0x0100
-
-#define E1000_NPTX 0x07 /* autoneg next page TX */
-#define E1000_NPTX_MSG_CODE_FIELD 0x0001
-#define E1000_NPTX_TOGGLE 0x0800
-#define E1000_NPTX_ACKNOWLDGE2 0x1000
-#define E1000_NPTX_MSG_PAGE 0x2000
-#define E1000_NPTX_NEXT_PAGE 0x8000
-
-#define E1000_RNPR 0x08 /* autoneg link-partner (?) next page */
-#define E1000_RNPR_MSG_CODE_FIELD 0x0001
-#define E1000_RNPR_TOGGLE 0x0800
-#define E1000_RNPR_ACKNOWLDGE2 0x1000
-#define E1000_RNPR_MSG_PAGE 0x2000
-#define E1000_RNPR_ACKNOWLDGE 0x4000
-#define E1000_RNPR_NEXT_PAGE 0x8000
-
-#define E1000_1GCR 0x09 /* 1000T (1G) control reg */
-#define E1000_1GCR_ASYM_PAUSE 0x0080
-#define E1000_1GCR_1000T 0x0100
-#define E1000_1GCR_1000T_FD 0x0200
-#define E1000_1GCR_REPEATER_DTE 0x0400
-#define E1000_1GCR_MS_VALUE 0x0800
-#define E1000_1GCR_MS_ENABLE 0x1000
-#define E1000_1GCR_TEST_MODE_NORMAL 0x0000
-#define E1000_1GCR_TEST_MODE_1 0x2000
-#define E1000_1GCR_TEST_MODE_2 0x4000
-#define E1000_1GCR_TEST_MODE_3 0x6000
-#define E1000_1GCR_TEST_MODE_4 0x8000
-#define E1000_1GCR_SPEED_MASK 0x0300
-
-#define E1000_1GSR 0x0A /* 1000T (1G) status reg */
-#define E1000_1GSR_IDLE_ERROR_CNT 0x0000
-#define E1000_1GSR_ASYM_PAUSE_DIR 0x0100
-#define E1000_1GSR_LP 0x0400
-#define E1000_1GSR_LP_FD 0x0800
-#define E1000_1GSR_REMOTE_RX_STATUS 0x1000
-#define E1000_1GSR_LOCAL_RX_STATUS 0x2000
-#define E1000_1GSR_MS_CONFIG_RES 0x4000
-#define E1000_1GSR_MS_CONFIG_FAULT 0x8000
-
-#define E1000_ESR 0x0F /* IEEE extended status reg */
-#define E1000_ESR_1000T 0x1000
-#define E1000_ESR_1000T_FD 0x2000
-#define E1000_ESR_1000X 0x4000
-#define E1000_ESR_1000X_FD 0x8000
-
+#if 0 /* XXX What is this? */
#define E1000_TX_POLARITY_MASK 0x0100
#define E1000_TX_NORMAL_POLARITY 0
#define E1000_AUTO_POLARITY_DISABLE 0x0010
+#endif
#define E1000_SCR 0x10 /* special control register */
#define E1000_SCR_JABBER_DISABLE 0x0001
diff -r 3926a2d9bd53 -r 61938b678016 sys/dev/mii/makphy.c
--- a/sys/dev/mii/makphy.c Mon Jun 18 09:11:03 2018 +0000
+++ b/sys/dev/mii/makphy.c Mon Jun 18 09:12:17 2018 +0000
@@ -1,4 +1,4 @@
-/* $NetBSD: makphy.c,v 1.44 2018/06/16 17:44:53 jdolecek Exp $ */
+/* $NetBSD: makphy.c,v 1.45 2018/06/18 09:12:17 msaitoh Exp $ */
/* $OpenBSD: eephy.c,v 1.56 2015/03/14 03:38:48 jsg Exp $ */
/*-
@@ -96,7 +96,7 @@
*/
#include <sys/cdefs.h>
-__KERNEL_RCSID(0, "$NetBSD: makphy.c,v 1.44 2018/06/16 17:44:53 jdolecek Exp $");
+__KERNEL_RCSID(0, "$NetBSD: makphy.c,v 1.45 2018/06/18 09:12:17 msaitoh Exp $");
#include <sys/param.h>
#include <sys/systm.h>
@@ -286,14 +286,14 @@
{
int reg, i;
- reg = PHY_READ(sc, E1000_CR);
- reg |= E1000_CR_RESET;
- PHY_WRITE(sc, E1000_CR, reg);
+ reg = PHY_READ(sc, MII_BMCR);
+ reg |= BMCR_RESET;
+ PHY_WRITE(sc, MII_BMCR, reg);
for (i = 0; i < 500; i++) {
DELAY(1);
- reg = PHY_READ(sc, E1000_CR);
- if (!(reg & E1000_CR_RESET))
+ reg = PHY_READ(sc, MII_BMCR);
+ if (!(reg & BMCR_RESET))
break;
}
@@ -363,9 +363,9 @@
* Disable autonegotiation, such that all capabilities get
* advertised when it is switched back on.
*/
- reg = PHY_READ(sc, E1000_CR);
- reg &= ~E1000_CR_AUTO_NEG_ENABLE;
- PHY_WRITE(sc, E1000_CR, reg | E1000_CR_RESET);
+ reg = PHY_READ(sc, MII_BMCR);
+ reg &= ~BMCR_AUTOEN;
+ PHY_WRITE(sc, MII_BMCR, reg | BMCR_RESET);
}
static int
@@ -392,8 +392,8 @@
* isolate ourselves.
*/
if (IFM_INST(ife->ifm_media) != sc->mii_inst) {
- bmcr = PHY_READ(sc, E1000_CR);
- PHY_WRITE(sc, E1000_CR, bmcr | E1000_CR_ISOLATE);
+ bmcr = PHY_READ(sc, MII_BMCR);
+ PHY_WRITE(sc, MII_BMCR, bmcr | BMCR_ISO);
return (0);
}
@@ -410,8 +410,8 @@
* software reset for the settings to take effect.
*/
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO) {
- bmcr = PHY_READ(sc, E1000_CR);
- PHY_WRITE(sc, E1000_CR, bmcr | E1000_CR_RESET);
+ bmcr = PHY_READ(sc, MII_BMCR);
+ PHY_WRITE(sc, MII_BMCR, bmcr | BMCR_RESET);
}
break;
@@ -423,12 +423,12 @@
return (0);
if (mii_phy_tick(sc) == EJUSTRETURN)
- return (0);
+ return (0);
break;
case MII_DOWN:
mii_phy_down(sc);
- return (0);
+ return (0);
}
/* Update the media status. */
@@ -448,13 +448,19 @@
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
- bmcr = PHY_READ(sc, E1000_CR);
+ bmcr = PHY_READ(sc, MII_BMCR);
ssr = PHY_READ(sc, E1000_SSR);
if (ssr & E1000_SSR_LINK)
mii->mii_media_status |= IFM_ACTIVE;
- if (bmcr & E1000_CR_LOOPBACK)
+ if (bmcr & BMCR_ISO) {
+ mii->mii_media_active |= IFM_NONE;
+ mii->mii_media_status = 0;
+ return;
+ }
+
+ if (bmcr & BMCR_LOOP)
mii->mii_media_active |= IFM_LOOP;
if (!(ssr & E1000_SSR_SPD_DPLX_RESOLVED)) {
@@ -480,8 +486,8 @@
mii->mii_media_active |= IFM_HDX;
if (IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T) {
- gsr = PHY_READ(sc, E1000_1GSR) | PHY_READ(sc, E1000_1GSR);
- if (gsr & E1000_1GSR_MS_CONFIG_RES)
+ gsr = PHY_READ(sc, MII_100T2SR) | PHY_READ(sc, MII_100T2SR);
+ if (gsr & GTSR_MS_RES)
mii->mii_media_active |= IFM_ETH_MASTER;
}
}
Home |
Main Index |
Thread Index |
Old Index