[src/trunk]: src/sys/arch/mips/ingenic add SMBus registers

[macallan <macallan%NetBSD.org@localhost>]

details:   https://anonhg.NetBSD.org/src/rev/17d94a01a3ad
branches:  trunk
changeset: 336780:17d94a01a3ad
user:      macallan <macallan%NetBSD.org@localhost>
date:      Thu Mar 19 12:22:36 2015 +0000

description:
add SMBus registers

diffstat:

 sys/arch/mips/ingenic/ingenic_regs.h |  69 +++++++++++++++++++++++++++++++++++-
 1 files changed, 68 insertions(+), 1 deletions(-)

diffs (81 lines):

diff -r 2525e55dce28 -r 17d94a01a3ad sys/arch/mips/ingenic/ingenic_regs.h
--- a/sys/arch/mips/ingenic/ingenic_regs.h      Thu Mar 19 12:22:00 2015 +0000
+++ b/sys/arch/mips/ingenic/ingenic_regs.h      Thu Mar 19 12:22:36 2015 +0000
@@ -1,4 +1,4 @@
-/*     $NetBSD: ingenic_regs.h,v 1.10 2015/03/17 07:22:40 macallan Exp $ */
+/*     $NetBSD: ingenic_regs.h,v 1.11 2015/03/19 12:22:36 macallan Exp $ */
 
 /*-
  * Copyright (c) 2014 Michael Lorenz
@@ -380,4 +380,71 @@
 #define JZ_SMB3_BASE   0x10053000
 #define JZ_SMB4_BASE   0x10054000
 
+/* SMBus register offsets, per port */
+#define JZ_SMBCON      0x00 /* SMB control */
+       #define JZ_STPHLD       0x80 /* Stop Hold Enable bit */
+       #define JZ_SLVDIS       0x40 /* 1 - slave disabled */
+       #define JZ_REST         0x20 /* 1 - allow RESTART */
+       #define JZ_MATP         0x10 /* 1 - enable 10bit addr. for master */
+       #define JZ_SATP         0x08 /* 1 - enable 10bit addr. for slave */
+       #define JZ_SPD_M        0x06 /* bus speed control */
+       #define JZ_SPD_100KB    0x02 /* 100kBit/s mode */
+       #define JZ_SPD_400KB    0x04 /* 400kBit/s mode */
+       #define JZ_MD           0x01 /* enable master */
+#define JZ_SMBTAR      0x04 /* SMB target address */
+       #define JZ_SMATP        0x1000 /* enable 10bit master addr */
+       #define JZ_SPECIAL      0x0800 /* 1 - special command */
+       #define JZ_START        0x0400 /* 1 - send START */
+       #define JZ_SMBTAR_M     0x03ff /* target address */
+#define JZ_SMBSAR      0x08 /* SMB slave address */
+#define JZ_SMBDC       0x10 /* SMB data buffer and command */
+       #define JZ_CMD  0x100 /* 1 - read, 0 - write */
+       #define JZ_DATA 0x0ff
+#define JZ_SMBSHCNT    0x14 /* Standard speed SMB SCL high count */
+#define JZ_SMBSLCNT    0x18 /* Standard speed SMB SCL low count */
+#define JZ_SMBFHCNT    0x1C /* Fast speed SMB SCL high count */
+#define JZ_SMBFLCNT    0x20 /* Fast speed SMB SCL low count */
+#define JZ_SMBINTST    0x2C /* SMB Interrupt Status */
+       #define JZ_ISTT         0x400   /* START or RESTART occured */
+       #define JZ_ISTP         0x200   /* STOP occured */
+       #define JZ_TXABT        0x40    /* ABORT occured */
+       #define JZ_TXEMP        0x10    /* TX FIFO is low */
+       #define JZ_TXOF         0x08    /* TX FIFO is high */
+       #define JZ_RXFL         0x04    /* RX FIFO is low */
+       #define JZ_RXOF         0x02    /* RX FIFO is high */
+       #define JZ_RXUF         0x01    /* RX FIFO underflow */
+#define JZ_SMBINTM     0x30 /* SMB Interrupt Mask */
+#define JZ_SMBRXTL     0x38 /* SMB RxFIFO Threshold */
+#define JZ_SMBTXTL     0x3C /* SMB TxFIFO Threshold */
+#define JZ_SMBCINT     0x40 /* Clear Interrupts */
+       #define JZ_CLEARALL     0x01
+#define JZ_SMBCRXUF    0x44 /* Clear RXUF Interrupt */
+#define JZ_SMBCRXOF    0x48 /* Clear RX_OVER Interrupt */
+#define JZ_SMBCTXOF    0x4C /* Clear TX_OVER Interrupt */
+#define JZ_SMBCRXREQ   0x50 /* Clear RDREQ Interrupt */
+#define JZ_SMBCTXABT   0x54 /* Clear TX_ABRT Interrupt */
+#define JZ_SMBCRXDN    0x58 /* Clear RX_DONE Interrupt */
+#define JZ_SMBCACT     0x5c /* Clear ACTIVITY Interrupt */
+#define JZ_SMBCSTP     0x60 /* Clear STOP Interrupt */
+#define JZ_SMBCSTT     0x64 /* Clear START Interrupt */
+#define JZ_SMBCGC      0x68 /* Clear GEN_CALL Interrupt */
+#define JZ_SMBENB      0x6C /* SMB Enable */
+       #define JZ_ENABLE       0x01
+#define JZ_SMBST       0x70 /* SMB Status register */
+       #define JZ_SLVACT       0x40 /* slave is active */
+       #define JZ_MSTACT       0x20 /* master is active */
+       #define JZ_RFF          0x10 /* RX FIFO is full */
+       #define JZ_RFNE         0x08 /* RX FIFO not empty */
+       #define JZ_TFE          0x04 /* TX FIFO is empty */
+       #define JZ_TFNF         0x02 /* TX FIFO is not full */
+       #define JZ_ACT          0x01 /* JZ_SLVACT | JZ_MSTACT */
+#define JZ_SMBABTSRC   0x80 /* SMB Transmit Abort Status Register */
+#define JZ_SMBDMACR    0x88 /* DMA Control Register */
+#define JZ_SMBDMATDL   0x8c /* DMA Transmit Data Level */
+#define JZ_SMBDMARDL   0x90 /* DMA Receive Data Level */
+#define JZ_SMBSDASU    0x94 /* SMB SDA Setup Register */
+#define JZ_SMBACKGC    0x98 /* SMB ACK General Call Register */
+#define JZ_SMBENBST    0x9C /* SMB Enable Status Register */
+#define JZ_SMBSDAHD    0xD0 /* SMB SDA HolD time Register */
+
 #endif /* INGENIC_REGS_H */