On Sun, 19 Dec 1999, Wolfgang Rupprecht wrote:

> Castor Fu writes:
> > Make sure the pnpbios stuff is turned off.  This doesn't work with
> > my n505-ve.
> 
> Thanks, turning off pnpbios was the trick to keep it from crashing.
> 
> Now my problem is that no combination of pcic_isa_alloc_mask that I've
> tried will get me a functional ep0.
> A default gets me a complaint of a stray irq 4,7 at the point when the
> ep0 is enabled.  Masking 4 and 7 off gets rid of the stray interrupt
> complaint, but I see no packets sent out when watched via a tcpdump on
> another machine.
> 
>     option  PCIC_ISA_INTR_ALLOC_MASK=0xff6f
> 
> What was your irq mask?  Are you using the PCIBIOS_INTR_FIXUP stuff?

I used the defaults for the PCIBIOS stuff, and it seemed to work fine.
	#
	options PCIBIOS
	options PCIBIOSVERBOSE
	options PCIBIOS_INTR_FIXUP
	options PCIINTR_DEBUG
	options PCIBIOS_BUS_FIXUP
	#

And I've appended some dmesg output.  I hope this helps.

	-castor


BIOS32 rev. 0 found at 0xfd8a0
PCI BIOS rev. 2.1 found at 0xfd9be
pcibios: config mechanism [1][x], special cycles [x][x], last bus 0
PCI IRQ Routing Table rev. 1.0 found at 0xfdf60, size 128 bytes (6 entries)
PCI Interrupt Router at 000:07:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
PIR Entry 0:
	Bus: 0  Device: 7
		INTA: link 0x00 bitmap 0x0000
		INTB: link 0x00 bitmap 0x0000
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x63 bitmap 0x0200
PIR Entry 1:
	Bus: 0  Device: 10
		INTA: link 0x60 bitmap 0x0008
		INTB: link 0x61 bitmap 0x0200
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x00 bitmap 0x0000
PIR Entry 2:
	Bus: 0  Device: 8
		INTA: link 0x63 bitmap 0x0200
		INTB: link 0x00 bitmap 0x0000
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x00 bitmap 0x0000
PIR Entry 3:
	Bus: 0  Device: 9
		INTA: link 0x62 bitmap 0x0200
		INTB: link 0x00 bitmap 0x0000
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x00 bitmap 0x0000
PIR Entry 4:
	Bus: 0  Device: 11
		INTA: link 0x60 bitmap 0x0008
		INTB: link 0x00 bitmap 0x0000
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x00 bitmap 0x0000
PIR Entry 5:
	Bus: 0  Device: 12
		INTA: link 0x61 bitmap 0x0200
		INTB: link 0x00 bitmap 0x0000
		INTC: link 0x00 bitmap 0x0000
		INTD: link 0x00 bitmap 0x0000
pciintr_link_fixup: PIRQ 0 already connected to IRQ 3
pciintr_link_fixup: PIRQ 3 not connected, assigning IRQ 9
pciintr_link_fixup: PIRQ 1 not connected, assigning IRQ 9
pciintr_link_fixup: PIRQ 2 not connected, assigning IRQ 9
--------------------------------------------
  device vendor product pin PIRQ   IRQ stage
--------------------------------------------
000:07:2 0x8086 0x7112  D   0x03   09  1
000:08:0 0x104d 0x8039  A   0x03   09  1
000:09:0 0x1073 0x0010  A   0x02   09  1
000:10:0 0x10c8 0x0005  A   0x00   03  0
000:11:0 0x127a 0x2005  A   0x00   03  0
000:12:0 0x1180 0x0475  A   0x01   09  1
--------------------------------------------
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI bus #1 is the last bus
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0