=2D----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

My Sony laptop hangs during boot-up with a kernel built from this AMs sourc=
es.=20
The hang occurs right after:

sd1 at scsibus0 target 1 lun 0: <I0MEGA, Mini  64*IOM, 3.04> disk removable

A dmesg from a kernel built from yesterdays sources follows:

NetBSD 1.6Y (KERNEL) #31: Thu Sep  4 14:21:08 MDT 2003
       =20
root@laptop.mobile.johnrshannon.com:/usr/obj/sys/arch/i386/compile.i386/KER=
NEL
total memory =3D 511 MB
avail memory =3D 469 MB
using 6144 buffers containing 26268 KB of memory
BIOS32 rev. 0 found at 0xfd890
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium 4 (686-class), 1988.62 MHz, id 0xf27
cpu0: features bfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features bfebf9ff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebf9ff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64b/line 4-way
cpu0: L2 cache 512 KB 64b/line 8-way
cpu0: ITLB 4K/4M: 128 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: 16 page colors
acpi0 at mainbus0
acpi0: using Intel ACPI CA subsystem version 20030228
acpi0: X/RSDT: OemId <  SONY,      B1,20021203>, AslId <PTL ,00000000>
acpi0: SCI interrupting at int 9
    ACPI-0353: *** Error: Could not install PciConfig handler for PCI0,=20
AE_ALREADY_EXISTS
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C0D at acpi0 not configured
PNP0C0C at acpi0 not configured
PNP0A03 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0800 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0303 at acpi0 not configured
SNY9003 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
PNP0501 at acpi0 not configured
PNP0401 at acpi0 not configured
SNY5001 at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82845 Host (rev. 0x04)
pchb0: random number generator enabled
agp0 at pchb0: aperture at 0xec000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82845 AGP (rev. 0x04)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 0 function 0: ATI Technologies Radeon Mobility M7 LW (AGP)=
=20
(rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
uhci0 at pci0 dev 29 function 0: Intel 82801CA/CAM USB Controller (rev. 0x0=
2)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801CA/CAM USB Controller (rev. 0x0=
2)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801CA/CAM USB Controller (rev. 0x0=
2)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev. 0x42)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 5 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0xa8)
cbb1 at pci2 dev 5 function 1: Ricoh 5C476 PCI-CardBus bridge (rev. 0xa8)
Ricoh 5C552 PCI-CardBus bridge/Firewire (Firewire serial bus, interface 0x1=
0)=20
at pci2 dev 5 function 2 not configured
fxp0 at pci2 dev 8 function 0: Intel PRO/100 VE Network Controller, rev 66
fxp0: interrupting at irq 9
fxp0: Ethernet address 08:00:46:82:1d:e1
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: interrupting at irq 9
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 0 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 9
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 0 device 0
pcmcia1 at cardslot1
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801CAM LPC Interface (rev. 0x02)
pciide0 at pci0 dev 31 function 1: Intel 82801CA IDE Controller (ICH3) (rev=
=2E=20
0x02)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IC25N040ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA=
=20
data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <UJDA740 DVD/CDRW, , 1.00> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA=
=20
data transfers)
Intel 82801CA/CAM SMBus Controller (SMBus serial bus, revision 0x02) at pci=
0=20
dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801CA (ICH3) AC-97 Audio
auich0: interrupting at irq 9
auich0: Yamaha YMF753-S codec; 18 bit DAC, no 3D stereo
auich0: S/PDIF
audio0 at auich0: full duplex, independent
Intel 82801CA/CAM Modem (modem communications, revision 0x02) at pci0 dev 3=
1=20
function 6 not configured
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
uhidev0 at uhub1 port 2 configuration 1 interface 0umass0 at uhub0 port 1=20
configuration 1 interface 0
uhidev0: Agiler 3D USB Mouse, rev 1.00/5.00, addr 2, iclass 3/1

umass0: I0MEGA Minidrive  64, rev 2.00/2.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
ums0 at uhidev0: 5 buttons and Z dir.
wsmouse1 at ums0 mux 0
umass1 at uhub2 port 1 configuration 1 interface 0scsibus0: waiting 2 secon=
ds=20
for devices to settle...

umass1: Sony USB Memory Stick Slot, rev 1.10/1.40, addr 2
umass1: using UFI over CBI
atapibus1 at umass1 channel 0: 2 targets
sd0 at atapibus1 drive 0: <Sony, MSC-U03, 1.00> disk removable
sd0: drive offline
sd1 at scsibus0 target 1 lun 0: <I0MEGA, Mini  64*IOM, 3.04> disk removable
sd1: 63920 KB, 62 cyl, 64 head, 32 sec, 512 bytes/sect x 127840 sectors
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

=2D --=20

John R. Shannon
john@johnrshannon.com
=2D----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (NetBSD)

iEYEARECAAYFAj9YoEUACgkQOKbCxya4HYvzsgCgiqf/ISdwm1sYvrMw52+Tc8dW
NqMAoK2rVh3bc86KvJeWbGWqqtg4vObi
=3Doel3
=2D----END PGP SIGNATURE-----