On Tue, May 18, 2004 at 11:39:46AM -0700, Andrey Petrov wrote:
> Looks like interrupts are not delivered/processed correctly. I suspect
> interrupt vector number was not determined correctly. It would be
> interesting to look at firmware configuration (prtconf -pv) ...

I can neither find that command under NetBSD nor is it recognized by
the OBP. Are you talking about the Solaris command?

> ... and complete bootlog.

Here it is:

NetBSD 2.0E (SHERIDAN) #0: Tue May 18 19:30:36 CEST 2004
	tron@lyssa.zhadum.de:/src/sys/compile/SHERIDAN
total memory = 1024 MB
avail memory = 993 MB
bootpath: /pci@1f,4000/scsi@3,0/disk@0,0
mainbus0 (root): SUNW,Ultra-60: hostid 80a929ed
cpu0 at mainbus0: SUNW,UltraSPARC-II @ 450.016 MHz, version 0 FPU
cpu0: 32K instruction (32 b/l), 16K data (32 b/l), 4096K external (64 b/l)
psycho0 at mainbus0 addr 0xfffb4000
SUNW,psycho: impl 0, version 4: ign 7c0 bus range 0 to 0; PCI bus 0
DVMA map: fe000000 to ffffe000
IOTSB: 819ba000 to 819c2000
pci0 at psycho0
pci0: i/o space, memory space enabled
ebus0 at pci0 dev 1 function 0
ebus0: Sun Microsystems, Inc. PCIO Ebus2, revision 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-72f003
power at ebus0 addr 724000-724003 not configured
SUNW,pll at ebus0 addr 504000-504002 not configured
sc at ebus0 addr 500000-500007 not configured
sab0 at ebus0 addr 400000-40007f ipl 43: rev 3.2
sabtty0 at sab0 port 0: console i/o
sabtty1 at sab0 port 1
com0 at ebus0 addr 3083f8-3083ff ipl 41: ns16550a, working fifo
kbd0 at com0
com1 at ebus0 addr 3062f8-3062ff ipl 42: ns16550a, working fifo
ms0 at com1
lpt0 at ebus0 addr 3043bc-3043cb, 300398-300399, 700000-70000f ipl 34
fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 not configured
clock0 at ebus0 addr 0-1fff: mk48t59
flashprom at ebus0 addr 0-fffff not configured
audiocs0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 722000-722003 ipl 35 ipl 36: CS4231A
audio0 at audiocs0: full duplex
hme0 at pci0 dev 1 function 1: Sun Happy Meal Ethernet, rev. 1
hme0: interrupting at ivec 3021
hme0: Ethernet address 08:00:20:a9:29:ed
qsphy0 at hme0 phy 1: QS6612 10/100 media interface, rev. 1
qsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
esiop0 at pci0 dev 3 function 0: Symbios Logic 53c875 (ultra-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 20
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci0 dev 3 function 1: Symbios Logic 53c875 (ultra-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 26
scsibus1 at esiop1: 16 targets, 8 luns per target
psycho1 at mainbus0 addr 0xfffc6000
SUNW,psycho: impl 0, version 4: ign 7c0 bus range 128 to 128; PCI bus 128
pci1 at psycho1
pci1: i/o space, memory space enabled
bge0 at pci1 dev 1 function 0: Broadcom BCM5701 Gigabit Ethernet
bge0: interrupting at ivec 0
bge0: firmware handshake timed out, val = 4b657654
bge0: ASIC BCM5701 B5 (0x0105), Ethernet address 00:0a:5e:1e:97:d5
brgphy0 at bge0 phy 1: BCM5701 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
timer0 at mainbus0 addr 0xfff9fc00 irq vectors 7ec and 7ed
SUNW,afb at mainbus0 addr 0xfebc0000 not configured
pcons at mainbus0 not configured
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <FUJITSU, MAA3182SCX, 2411> disk fixed
sd0: 17482 MB, 9041 cyl, 19 head, 208 sec, 512 bytes/sect x 35803490 sectors
sd0: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <FUJITSU, MAA3182SC, 2411> disk fixed
sd1: 17267 MB, 9041 cyl, 19 head, 204 sec, 516 bytes/sect x 35090420 sectors
sd1: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
sd1: no disk label
root on sd0a dumps on sd0b
root file system type: ffs

	Kind regards

-- 
Matthias Scheler                                  http://scheler.de/~matthias/