Current-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: jmide regression on amd64/current
Manuel Bouyer wrote:
On Thu, Mar 27, 2008 at 06:21:38PM -0700, Scott Ellis wrote:
After noticing an issue with not being able to set the MTU on my msk(4)
(I think the arguments in ifioctl_common() are reversed, but that's
another story), I figured I'd update from Feb 11 -current amd64 to today
(March 27). Upon doing so, I find that the drive connected to jmide0 no
longer is attached correctly.
Using the Feb 11 kernel, I see:
[...]
jmide0 at pci5 dev 0 function 0: vendor 0x197b product 0x2363
jmide0: 1 PATA port, 2 SATA ports
jmide0: interrupting at ioapic0 pin 17 (irq 10)
ahcisata0 at jmide0
ahcisata0: AHCI revision 1.0, 2 ports, 32 command slots, features 0xc722e000
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
jmide1 at pci5 dev 0 function 1: vendor 0x197b product 0x2363
jmide1: 1 PATA port, 2 SATA ports
jmide1: interrupting at ioapic0 pin 18 (irq 0)
jmide1: PCI IDE interface used
jmide1: device disabled (at device)
[...]
wd0 at atabus1 drive 0: <WDC WD5000YS-01MPB0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6
(Ultra/133) (using DMA)
Updating to the March 27th kernel instead yields:
[...]
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
ahcisata0 port 1: device present, speed: 3.0Gb/s
wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
ahcisata0 port 1: device present, speed: 3.0Gb/s
[...]
This continues forever, which is less than satisfying. :-) Looking at
changes to jmide.c, I don't see anything immediately obvious, but I'm
not sure about the SATA DVD changes that went in. They look fine, but
that's where my eye is drawn.
Any ideas here? (The drive really is alive...booting back on the Feb 11
kernel makes it come alive and behave fine.)
Looks like an interrupt issue (the driver's interrupt handler may not be
called). Did the boot message about jmide* interrupts
change between the two kernels ?
Well, that sounds like a good theory, but aside from some differences in
the probe order, it doesn't look like there's much of a change between
the two.
In the "working" case (Feb 11th kernel, in "P5W_working2_dmesg.txt"
attachment), wd0 is detected fine. In the non-working case (-current as
of April 2nd, in "P5W_nojmide_dmesg.txt") wd0 is detected as a 64M ST506
drive (hah!), and then gives the timeout errors shown above.
Ideas on what files to try and revert, or if there's something in the
debugger I can look at to help figure this out?
ScottE
NetBSD 4.99.54 (INTREPID.P5W) #1: Mon Feb 11 16:36:24 PST 2008
scotte@intrepid:/nbu/source/netbsd/src/obj.amd64/nbu/source/netbsd/src/sys/arch/amd64/compile/INTREPID.P5W
total memory = 4095 MB
avail memory = 3954 MB
SMBIOS rev. 2.4 @ 0xf0690 (72 entries)
ASUSTEK COMPUTER INC P5W DH Deluxe (System Version)
mainbus0 (root)
cpu0 at mainbus0 apid 0: (boot processor)
cpu0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz, 2703.59 MHz
cpu1 at mainbus0 apid 1: (application processor)
cpu1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz, 2703.61 MHz
ioapic0 at mainbus0 apid 2
acpi0 at mainbus0: Advanced Configuration and Power Interface
ACPI-Fast 24-bit timer
CPU1 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU2 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU3 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU4 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
PCI0 (PNP0A08) at acpi0 not configured
MCH (PNP0C01) at acpi0 not configured
PIC (PNP0000) at acpi0 not configured
DMAD (PNP0200) at acpi0 not configured
attimer0 at acpi0 (TMR, PNP0100): AT Timer
attimer0: io 0x40-0x43 irq 0
RTC0 (PNP0B00) at acpi0 not configured
pcppi0 at acpi0 (SPKR, PNP0800)
pcppi0: io 0x61
sysbeep0 at pcppi0
COPR (PNP0C04) at acpi0 not configured
fdc0 at acpi0 (FDC, PNP0700)
fdc0: io 0x3f0-0x3f5,0x3f7 irq 6 drq 2
fdc0: expected BUFFER, got 4
SIOR (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
aiboost0 at acpi0 (ASOC, ATK0110-16843024)
aiboost0: ASUS AI Boost Hardware monitor
OMSC (PNP0C02) at acpi0 not configured
com0 at acpi0 (UAR1, PNP0501-1)
com0: io 0x3f8-0x3ff irq 4
com: ns16550a, working fifo
com0: console
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
LNKA (PNP0C0F) at acpi0 not configured
LNKB (PNP0C0F) at acpi0 not configured
LNKC (PNP0C0F) at acpi0 not configured
LNKD (PNP0C0F) at acpi0 not configured
LNKE (PNP0C0F) at acpi0 not configured
LNKF (PNP0C0F) at acpi0 not configured
LNKG (PNP0C0F) at acpi0 not configured
LNKH (PNP0C0F) at acpi0 not configured
pcppi0: attached to attimer0
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x277c (rev. 0xc0)
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x277d (rev. 0xc0)
pci1 at ppb0 bus 6
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 19 (irq 5)
azalia0: host: 0x8086/0x27d8 (rev. 1)
azalia0: host: High Definition Audio rev. 1.0
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
pci2 at ppb1 bus 5
ppb2 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x01)
pci3 at ppb2 bus 4
mskc0 at pci3 dev 0 function 0, Yukon-2 EC rev. A3 (0x2): ioapic0 pin 19 (irq 5)
msk0 at mskc0 port A: Ethernet address 00:1b:fc:03:ee:42
makphy0 at msk0 phy 0: Marvell 88E1111 Gigabit PHY, rev. 2
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x27e0 (rev. 0x01)
pci4 at ppb3 bus 3
mskc1 at pci4 dev 0 function 0, Yukon-2 EC rev. A3 (0x2): ioapic0 pin 16 (irq
11)
msk1 at mskc1 port A: Ethernet address 00:1b:fc:03:e3:60
makphy1 at msk1 phy 0: Marvell 88E1111 Gigabit PHY, rev. 2
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x27e2 (rev. 0x01)
pci5 at ppb4 bus 2
jmide0 at pci5 dev 0 function 0: vendor 0x197b product 0x2363
jmide0: 1 PATA port, 2 SATA ports
jmide0: interrupting at ioapic0 pin 17 (irq 10)
ahcisata0 at jmide0
ahcisata0: AHCI revision 1.0, 2 ports, 32 command slots, features 0xc722e000
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
jmide1 at pci5 dev 0 function 1: vendor 0x197b product 0x2363
jmide1: 1 PATA port, 2 SATA ports
jmide1: interrupting at ioapic0 pin 18 (irq 0)
jmide1: PCI IDE interface used
jmide1: device disabled (at device)
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 20 (irq 7)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 17 (irq 10)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
uhci2: interrupting at ioapic0 pin 18 (irq 10)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x01)
uhci3: interrupting at ioapic0 pin 19 (irq 5)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
ehci0: interrupting at ioapic0 pin 20 (irq 7)
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
pci6 at ppb5 bus 1
ex0 at pci6 dev 0 function 0: 3Com 3c905B-TX 10/100 Ethernet (rev. 0x30)
ex0: interrupting at ioapic0 pin 21 (irq 5)
ex0: MAC address 00:50:04:78:77:9c
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ex0: WARNING: powerhook_establish is deprecated
vendor 0x102b product 0x051b (VGA display) at pci6 dev 1 function 0 not
configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
ichlpcib0: 24-bit timer
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x01)
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus2 at piixide0 channel 0
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus3 at piixide0 channel 1
ahcisata1 at pci0 dev 31 function 2: vendor 0x8086 product 0x27c1
ahcisata1: interrupting at ioapic0 pin 23 (irq 11)
ahcisata1: AHCI revision 1.1, 4 ports, 32 command slots, features 0xc320e000
atabus4 at ahcisata1 channel 0
atabus5 at ahcisata1 channel 1
atabus6 at ahcisata1 channel 2
atabus7 at ahcisata1 channel 3
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
ichsmb0: interrupting at ioapic0 pin 23 (irq 0)
iic0 at ichsmb0: I2C bus
spdmem0 at iic0 addr 0x50
spdmem0: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz, PC2-6400
spdmem1 at iic0 addr 0x52
spdmem1: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz, PC2-6400
isa0 at ichlpcib0
ahcisata0 port 1: device present, speed: 3.0Gb/s
ahcisata1 port 0: device present, speed: 3.0Gb/s
ahcisata1 port 1: device present, speed: 3.0Gb/s
wd0 at atabus1 drive 0: <WDC WD5000YS-01MPB0>
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd1 at atabus4 drive 0: <WDC WD5000YS-01MPB1>
wd1: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd2 at atabus5 drive 0: <WDC WD5000YS-01MPB1>
wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uplcom0 at uhub2 port 1
uplcom0: vendor 0x067b product 0x2303, rev 1.10/2.02, addr 2
ucom0 at uplcom0
uhub5 at uhub4 port 7
uhub5: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/7.02, addr 2
uhub5: single transaction translator
uplcom1 at uhub2 port 2
uplcom1: vendor 0x067b product 0x2303, rev 1.10/2.02, addr 3
ucom1 at uplcom1
ugen0 at uhub5 port 3
ugen0: vendor 0x0bda RTL8187_Wireless, rev 2.00/1.00, addr 3
azalia0: codec[0]: Realtek ALC882 (rev. 1.1)
azalia0: codec[0]: High Definition Audio rev. 1.0
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
swwdog0: software watchdog initialized
NetBSD 4.99.58 (INTREPID.P5W) #3: Wed Apr 2 17:05:24 PDT 2008
scotte@intrepid:/nbu/source/netbsd/src/obj.amd64/nbu/source/netbsd/src/sys/arch/amd64/compile/INTREPID.P5W
total memory = 4095 MB
avail memory = 3954 MB
SMBIOS rev. 2.4 @ 0xf0690 (72 entries)
ASUSTEK COMPUTER INC P5W DH Deluxe (System Version)
mainbus0 (root)
cpu0 at mainbus0 apid 0: (boot processor)
cpu0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz, 2400.17 MHz
cpu1 at mainbus0 apid 1: (application processor)
cpu1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz, 2400.23 MHz
ioapic0 at mainbus0 apid 2
acpi0 at mainbus0: Advanced Configuration and Power Interface
ACPI-Fast 24-bit timer
CPU1 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU2 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU3 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU4 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
PCI0 (PNP0A08) at acpi0 not configured
MCH (PNP0C01) at acpi0 not configured
PIC (PNP0000) at acpi0 not configured
DMAD (PNP0200) at acpi0 not configured
attimer0 at acpi0 (TMR, PNP0100): AT Timer
attimer0: io 0x40-0x43 irq 0
RTC0 (PNP0B00) at acpi0 not configured
pcppi0 at acpi0 (SPKR, PNP0800)
pcppi0: io 0x61
sysbeep0 at pcppi0
COPR (PNP0C04) at acpi0 not configured
fdc0 at acpi0 (FDC, PNP0700)
fdc0: io 0x3f0-0x3f5,0x3f7 irq 6 drq 2
fdc0: expected BUFFER, got 4
SIOR (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
aiboost0 at acpi0 (ASOC, ATK0110-16843024)
aiboost0: ASUS AI Boost Hardware monitor
OMSC (PNP0C02) at acpi0 not configured
com0 at acpi0 (UAR1, PNP0501-1)
com0: io 0x3f8-0x3ff irq 4
com: ns16550a, working fifo
com0: console
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
LNKA (PNP0C0F) at acpi0 not configured
LNKB (PNP0C0F) at acpi0 not configured
LNKC (PNP0C0F) at acpi0 not configured
LNKD (PNP0C0F) at acpi0 not configured
LNKE (PNP0C0F) at acpi0 not configured
LNKF (PNP0C0F) at acpi0 not configured
LNKG (PNP0C0F) at acpi0 not configured
LNKH (PNP0C0F) at acpi0 not configured
attimer0: attached to pcppi0
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x277c (rev. 0xc0)
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x277d (rev. 0xc0)
pci1 at ppb0 bus 6
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 19 (irq 5)
azalia0: host: 0x8086/0x27d8 (rev. 1)
azalia0: host: High Definition Audio rev. 1.0
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
pci2 at ppb1 bus 5
ppb2 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x01)
pci3 at ppb2 bus 4
mskc0 at pci3 dev 0 function 0, Yukon-2 EC rev. A3 (0x2): ioapic0 pin 19 (irq 5)
msk0 at mskc0 port A: Ethernet address 00:1b:fc:03:ee:42
makphy0 at msk0 phy 0: Marvell 88E1111 Gigabit PHY, rev. 2
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x27e0 (rev. 0x01)
pci4 at ppb3 bus 3
mskc1 at pci4 dev 0 function 0, Yukon-2 EC rev. A3 (0x2): ioapic0 pin 16 (irq
11)
msk1 at mskc1 port A: Ethernet address 00:1b:fc:03:e3:60
makphy1 at msk1 phy 0: Marvell 88E1111 Gigabit PHY, rev. 2
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x27e2 (rev. 0x01)
pci5 at ppb4 bus 2
jmide0 at pci5 dev 0 function 0: vendor 0x197b product 0x2363
jmide0: 1 PATA port, 2 SATA ports
jmide0: interrupting at ioapic0 pin 17 (irq 10)
ahcisata0 at jmide0
ahcisata0: AHCI revision 1.0, 2 ports, 32 command slots, features 0xc722e000
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
jmide1 at pci5 dev 0 function 1: vendor 0x197b product 0x2363
jmide1: 1 PATA port, 2 SATA ports
jmide1: interrupting at ioapic0 pin 18 (irq 0)
jmide1: PCI IDE interface used
jmide1: device disabled (at device)
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 20 (irq 7)
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 17 (irq 10)
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
uhci2: interrupting at ioapic0 pin 18 (irq 10)
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x01)
uhci3: interrupting at ioapic0 pin 19 (irq 5)
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
ehci0: interrupting at ioapic0 pin 20 (irq 7)
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
pci6 at ppb5 bus 1
ex0 at pci6 dev 0 function 0: 3Com 3c905B-TX 10/100 Ethernet (rev. 0x30)
ex0: interrupting at ioapic0 pin 21 (irq 5)
ex0: MAC address 00:50:04:78:77:9c
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ex0: WARNING: powerhook_establish is deprecated
vendor 0x102b product 0x051b (VGA display) at pci6 dev 1 function 0 not
configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
ichlpcib0: 24-bit timer
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x01)
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus2 at piixide0 channel 0
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus3 at piixide0 channel 1
ahcisata1 at pci0 dev 31 function 2: vendor 0x8086 product 0x27c1
ahcisata1: interrupting at ioapic0 pin 23 (irq 11)
ahcisata1: AHCI revision 1.1, 4 ports, 32 command slots, features 0xc320e000
atabus4 at ahcisata1 channel 0
atabus5 at ahcisata1 channel 1
atabus6 at ahcisata1 channel 2
atabus7 at ahcisata1 channel 3
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
ichsmb0: interrupting at ioapic0 pin 23 (irq 0)
iic0 at ichsmb0: I2C bus
spdmem0 at iic0 addr 0x50
spdmem0: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz, PC2-6400
spdmem1 at iic0 addr 0x52
spdmem1: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz, PC2-6400
isa0 at ichlpcib0
azalia0: codec[0]: Realtek ALC882 (rev. 1.1)
azalia0: codec[0]: High Definition Audio rev. 1.0
audio0 at azalia0: full duplex, independent
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb1
uhub1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2 at usb2
uhub2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3 at usb3
uhub3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4 at usb4
uhub4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
ahcisata0 port 1: device present, speed: 3.0Gb/s
ahcisata1 port 0: device present, speed: 3.0Gb/s
ahcisata1 port 1: device present, speed: 3.0Gb/s
wd0 at atabus1 drive 0fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uplcom0 at uhub2 port 1
uplcom0: vendor 0x067b product 0x2303, rev 1.10/2.02, addr 2
ucom0 at uplcom0
uhub5 at uhub4 port 7
uhub5: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/7.02, addr 2
uhub5: single transaction translator
uplcom1 at uhub2 port 2
uplcom1: vendor 0x067b product 0x2303, rev 1.10/2.02, addr 3
ucom1 at uplcom1
ugen0 at uhub5 port 3
ugen0: vendor 0x0bda RTL8187_Wireless, rev 2.00/1.00, addr 3
: <ST506>
wd0: 69632 KB, 1024 cyl, 8 head, 17 sec, 512 bytes/sect x 139264 sectors
wd1 at atabus4 drive 0: <WDC WD5000YS-01MPB1>
wd1: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd2 at atabus5 drive 0: <WDC WD5000YS-01MPB1>
wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
Kernelized RAIDframe activated
swwdog0: software watchdog initialized
Home |
Main Index |
Thread Index |
Old Index