NetBSD on HP xw9400 - ACPI problem?

[Lars Nordlund <lars.nordlund%hem.utfors.se@localhost>]

Hi

I have NetBSD 5-stable amd64 on an HP xw 9400 workstation and it is
giving me some problems. The machine sometimes locks up. The hangs
seems to be related to disk work. When it happens it is usually while
doing 'cvs up' or some heavy pkgsrc build.

The machine is also not able to boot with ACPI enabled. It results in
timeouts on the sd0 device hanging on the SAS controller. This
behaviour has been the same since at least 5.0 was released and I
installed it on this machine.

See this dmesg from a failed boot on a recent current (with Joerg
Sonnenberger's acpi patch applied):

    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.22 (FOOBAR) #2: Wed Nov 11 15:06:52 CET 2009
        XXX@foobar:/home/XXX/tmp/current-obj_amd64/sys/arch/amd64/compile/FOOBAR
total memory = 4095 MB
avail memory = 3954 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP xw9400 Workstation ( )
mainbus0 (root)
ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 
0000000000000000/1 (20090730/tbfadt-655)
cpu0 at mainbus0 apid 0: AMD 686-class, 2400MHz, id 0x40f13
cpu1 at mainbus0 apid 1: AMD 686-class, 2400MHz, id 0x40f13
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 11, 24 pins
ioapic1 at mainbus0 apid 9: pa 0xfa400000, version 11, 24 pins
acpi0 at mainbus0: Intel ACPICA 20090730
acpi0: X/RSDT: OemId <HPQOEM,SLIC-WKS,20090421>, AslId <    ,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
pckbc1 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
pckbc2 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
COM1 (PNP0501) at acpi0 not configured
FDC0 (PNP0700) at acpi0 not configured
APIC (PNP0003) at acpi0 not configured
acpibut0 at acpi0 (PBTN, PNP0C0C): ACPI Power Button
acpiwmi0 at acpi0 (WMID, PNP0C14-0): ACPI WMI Interface
attimer1: attached to pcppi1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x0369 (RAM memory, revision 0xa2) at pci0 dev 0 function 
0 not configured
pcib0 at pci0 dev 1 function 0: vendor 0x10de product 0x0364 (rev. 0xa3)
nfsmbc0 at pci0 dev 1 function 1: vendor 0x10de product 0x0368 (rev. 0xa3)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x036c (rev. 0xa1)
ohci0: interrupting at ioapic0 pin 5
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 2 function 1: vendor 0x10de product 0x036d (rev. 0xa2)
ehci0: interrupting at ioapic0 pin 10
ehci0: EHCI version 1.0
ehci0: companion controller, 10 ports each: ohci0
usb1 at ehci0: USB revision 2.0
viaide0 at pci0 dev 4 function 0: NVIDIA MCP55 IDE Controller (rev. 0xa1)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel ignored (disabled)
viaide1 at pci0 dev 5 function 0: NVIDIA MCP55 Serial ATA Controller (rev. 0xa3)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
LSA0: Picked IRQ 16 with weight 0
viaide1: using ioapic0 pin 16 for native-PCI interrupt
atabus1 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus2 at viaide1 channel 1
viaide2 at pci0 dev 5 function 1: NVIDIA MCP55 Serial ATA Controller (rev. 0xa3)
viaide2: bus-master DMA support present
viaide2: primary channel wired to native-PCI mode
viaide2: using ioapic0 pin 5 for native-PCI interrupt
atabus3 at viaide2 channel 0
viaide2: secondary channel wired to native-PCI mode
atabus4 at viaide2 channel 1
viaide3 at pci0 dev 5 function 2: NVIDIA MCP55 Serial ATA Controller (rev. 0xa3)
viaide3: bus-master DMA support present
viaide3: primary channel wired to native-PCI mode
viaide3: using ioapic0 pin 10 for native-PCI interrupt
atabus5 at viaide3 channel 0
viaide3: secondary channel wired to native-PCI mode
atabus6 at viaide3 channel 1
ppb0 at pci0 dev 6 function 0: vendor 0x10de product 0x0370 (rev. 0xa2)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
fwohci0 at pci1 dev 5 function 0: vendor 0x104c product 0x8023 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 10
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:60:b0:00:00:24:68:5f
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
hdaudio0 at pci0 dev 6 function 1: HD Audio Controller
LAZA: Picked IRQ 17 with weight 0
hdaudio0: interrupting at ioapic0 pin 17
hdafg0 at hdaudio0 vendor 0x10EC product 0x0262 nid 0x01 (firmware 
configuration)
hdafg0: DAC0:02, Analog Speaker: Jack (Green, 15)
hdafg0: DAC0:02, Analog HP Out: Jack (Black, 1B)
hdafg0: ADC2:07, Analog Mic In: Jack (Pink, 18)
hdafg0: ADC2:07, Analog Mic In: Jack (Black, 19)
hdafg0: ADC2:07, Analog Line In: Jack (Blue, 1A)
hdafg0: ADC2:07, Analog CD: Fixed Function (Unknown, 1C)
hdafg0: ADC2:07, Analog AUX: Fixed Function (Unknown, 14)
hdafg0: DAC3:06, Digital SPDIF Out: Jack (Orange, 1E)
hdafg0: 2ch/2ch 44100Hz-192000Hz 16/16 20/32 24/32
audio0 at hdafg0: full duplex, playback, capture, independent
nfe0 at pci0 dev 8 function 0: vendor 0x10de product 0x0373 (rev. 0xa3)
nfe0: interrupting at ioapic0 pin 5
nfe0: Ethernet address 00:1c:c4:ad:c8:02
ukphy0 at nfe0 phy 0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
nfe1 at pci0 dev 9 function 0: vendor 0x10de product 0x0373 (rev. 0xa3)
nfe1: interrupting at ioapic0 pin 10
nfe1: Ethernet address 00:1c:c4:ad:c8:03
ukphy1 at nfe1 phy 1: OUI 0x000ac2, model 0x000b, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb1 at pci0 dev 13 function 0: vendor 0x10de product 0x0378 (rev. 0xa3)
pci2 at ppb1 bus 43
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci2 dev 0 function 0: vendor 0x1033 product 0x0125 (rev. 0x06)
pci3 at ppb2 bus 44
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci2 dev 0 function 1: vendor 0x1033 product 0x0125 (rev. 0x06)
ppb3: disabling notification events
pci4 at ppb3 bus 45
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 15 function 0: vendor 0x10de product 0x0377 (rev. 0xa3)
pci5 at ppb4 bus 24
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci5 dev 0 function 0: vendor 0x10de product 0x029e (rev. 0xa1)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
pchb0 at pci0 dev 24 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3: AMD CPU Temperature Sensors (K8: core rev 
JH-F3, socket F)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pci6 at mainbus0 bus 107
pci6: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
mpt0 at pci6 dev 0 function 0: vendor 0x1000 product 0x0058
mpt0: interrupting at ioapic1 pin 19
mpt0: Phy 0: Link Rate 3.0 Gbps
scsibus0 at mpt0: 112 targets, 8 luns per target
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
scsibus0: waiting 2 seconds for devices to settle...
uhub0 at usb0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 10 ports with 10 removable, self powered
uhub1 at usb1: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 10 ports with 10 removable, self powered
viaide1 port 0: device present, speed: 1.5Gb/s
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-ST DVD-RAM GSA-H60L, K1B7BL81125, R90A> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uhub2 at uhub1 port 8: vendor 0x0424 product 0x2504, class 9/0, rev 2.00/0.01, 
addr 2
uhub2: multiple transaction translators
uhub2: 4 ports with 4 removable, self powered
uhidev0 at uhub2 port 3 configuration 1 interface 0
uhidev0: vendor 0x0430 product 0x0100, rev 2.00/1.07, addr 3, iclass 3/1
ums0 at uhidev0: 3 buttons
wsmouse1 at ums0 mux 0
probe(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
probe(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
sd0 at scsibus0 target 0 lun 0: <FUJITSU, MBA3147RC, HPF1> disk fixed
sd0(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
sd0(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
sd0(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
sd0: 136 GB, 82594 cyl, 4 head, 867 sec, 512 bytes/sect x 286749488 sectors
sd0(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout
sd0(mpt0:0:0:0): command timeout
mpt0: recovered from command timeout


Any ideas?


Best regards,
        Lars Nordlund