PS2 Ports not working

[Shawn Novak <kernel86%gmail.com@localhost>]

I just installed the latest build (201112261820Z) from the nyftp to
use for some testing however the ps2 keyboard doesn't work.

I didn't note any messages about ps2 being configured or not, but
here's the dmesg output from the system after install.

dmesg:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.59 (GENERIC) #0: Tue Dec 27 01:19:11 UTC 2011
        
builds%b8.netbsd.org@localhost:/home/builds/ab/HEAD/i386/201112261820Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 3550 MB
avail memory = 3479 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
HP ProLiant DL145 G3 ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: Dual-Core AMD Opteron(tm) Processor 2214 HE, id 0x40f12
cpu0: SVM disabled by the BIOS
cpu1 at mainbus0 apid 1: Dual-Core AMD Opteron(tm) Processor 2214 HE, id 0x40f12
cpu2 at mainbus0 apid 2: Dual-Core AMD Opteron(tm) Processor 2214 HE, id 0x40f12
cpu3 at mainbus0 apid 3: Dual-Core AMD Opteron(tm) Processor 2214 HE, id 0x40f12
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0 apid 5: pa 0xfec01000, version 11, 16 pins
ioapic2 at mainbus0 apid 6: pa 0xfec02000, version 11, 16 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <PTLTD ,    XSDT  ,06040000>, AslId < LTP,00000000>
LNKU: ACPI: Found matching pin for 0.3.INTA at func 0: 10
LNKS: ACPI: Found matching pin for 1.14.INTA at func 0: 7
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
MCFG (PNP0C02) at acpi0 not configured
npx1 at acpi0 (FPU, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
SYSB (PNP0003) at acpi0 not configured
PCBR (PNP0C02) at acpi0 not configured
pckbc1 at acpi0 (Z000, PNP0303) (kbd port): io 0x60,0x64 irq 1
COMA (PNP0501) at acpi0 not configured
MI0 (IPI0001) at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ppb0 at pci0 dev 1 function 0: vendor 0x1166 product 0x0036 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci1 dev 13 function 0: vendor 0x1166 product 0x0104 (rev. 0xc0)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
svwsata0 at pci1 dev 14 function 0: ServerWorks HT-1000 SATA
Controller (rev. 0x00)
svwsata0: bus-master DMA support present
svwsata0: using ioapic0 pin 7 for native-PCI interrupt
svwsata0: primary channel wired to native-PCI mode
atabus0 at svwsata0 channel 0
svwsata0: secondary channel wired to native-PCI mode
atabus1 at svwsata0 channel 1
svwsata0: secondary channel wired to compatibility mode
atabus2 at svwsata0 channel 2
svwsata0: secondary channel configured to compatibility mode
atabus3 at svwsata0 channel 3
piixpm0 at pci0 dev 2 function 0
piixpm0: vendor 0x1166 product 0x0205 (rev. 0x00)
piixpm0: polling
iic0 at piixpm0: I2C bus
rccide0 at pci0 dev 2 function 1: ServerWorks HT-1000 IDE Controller (rev. 0x00)
rccide0: bus-master DMA support present
rccide0: primary channel configured to compatibility mode
rccide0: primary channel interrupting at ioapic0 pin 14
atabus4 at rccide0 channel 0
rccide0: secondary channel configured to compatibility mode
rccide0: secondary channel interrupting at ioapic0 pin 15
atabus5 at rccide0 channel 1
pcib0 at pci0 dev 2 function 2: vendor 0x1166 product 0x0234 (rev. 0x00)
ohci0 at pci0 dev 3 function 0: vendor 0x1166 product 0x0223 (rev. 0x01)
ohci0: interrupting at ioapic0 pin 10
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 3 function 1: vendor 0x1166 product 0x0223 (rev. 0x01)
ohci1: interrupting at ioapic0 pin 10
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 3 function 2: vendor 0x1166 product 0x0223 (rev. 0x01)
ehci0: interrupting at ioapic0 pin 10
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
vga1 at pci0 dev 4 function 0: vendor 0x102b product 0x0522 (rev. 0x02)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ppb2 at pci0 dev 6 function 0: vendor 0x1166 product 0x0140 (rev. 0xa2)
ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 7 function 0: vendor 0x1166 product 0x0142 (rev. 0xa2)
ppb3: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 8 function 0: vendor 0x1166 product 0x0144 (rev. 0xa2)
ppb4: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
ppb5 at pci0 dev 9 function 0: vendor 0x1166 product 0x0142 (rev. 0xa2)
ppb5: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
ppb6 at pci0 dev 10 function 0: vendor 0x1166 product 0x0144 (rev. 0xa2)
ppb6: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci7 at ppb6 bus 7
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
ppb7 at pci7 dev 0 function 0: vendor 0x1166 product 0x0103 (rev. 0xb5)
ppb7: PCI Express 1.0 <PCI-E to PCI/PCI-X Bridge>
pci8 at ppb7 bus 8
pci8: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci8 dev 4 function 0: Broadcom BCM5715 Gigabit Ethernet
bge0: interrupting at ioapic2 pin 4
bge0: ASIC BCM5715 A3 (0x9003), Ethernet address 00:18:71:86:f3:89
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5714 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge1 at pci8 dev 4 function 1: Broadcom BCM5715 Gigabit Ethernet
bge1: interrupting at ioapic2 pin 4
bge1: ASIC BCM5715 A3 (0x9003), Ethernet address 00:18:71:87:49:08
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 1: BCM5714 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
pchb0 at pci0 dev 24 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3: vendor 0x1022 product 0x1103 (rev. 0x00)
amdtemp0 at pchb3: AMD CPU Temperature Sensors (K8: core rev JH-F2, socket F)
pchb4 at pci0 dev 25 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb5 at pci0 dev 25 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb6 at pci0 dev 25 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb7 at pci0 dev 25 function 3: vendor 0x1022 product 0x1103 (rev. 0x00)
amdtemp1 at pchb7: AMD CPU Temperature Sensors (K8: core rev JH-F2, socket F)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: P0: FFH, lat 100 us, pow 100000 mW, 2200 MHz
acpicpu0: P1: FFH, lat 100 us, pow 83781 mW, 2000 MHz
acpicpu0: P2: FFH, lat 100 us, pow 75142 mW, 1800 MHz
acpicpu0: P3: FFH, lat 100 us, pow 38194 mW, 1000 MHz
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x1166 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1166 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1166 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
svwsata0 port 3: PHY offline
svwsata0 port 2: PHY offline
svwsata0 port 1: PHY offline
svwsata0 port 0: PHY offline
wd0 at atabus4 drive 0
wd0: <SILICONSYSTEMS INC 512MB-3625>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 497 MB, 1011 cyl, 16 head, 63 sec, 512 bytes/sect x 1019088 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
wd0(rccide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
uhub3 at uhub2 port 3: vendor 0x04cc product 0x1520, class 9/0, rev
2.00/2.00, addr 2
uhub3: single transaction translator
uhub3: 3 ports with 3 removable, self powered
umass0 at uhub3 port 1 configuration 1 interface 0
umass0: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
cd0 at scsibus0 target 0 lun 0: <HL-DT-ST, DVDRRW GSA-H20L, S742>
cdrom removable
uhidev0 at uhub3 port 2 configuration 1 interface 0
uhidev0: Logitech USB Receiver, rev 1.10/17.11, addr 4, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub3 port 2 configuration 1 interface 1
uhidev1: Logitech USB Receiver, rev 1.10/17.11, addr 4, iclass 3/1
uhidev1: 4 report ids
ums0 at uhidev1 reportid 1: 16 buttons and Z dir
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 4: input=3, output=0, feature=0
ehci0: handing over full speed device on port 4 to ohci1
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
urndis0 at uhub1 port 2 configuration 1 interface 0
urndis0: ServerEngines SE USB Device, rev 1.10/0.01, addr 2
urndis0: could not find data bulk in
urndis0: could not find data bulk out
urndis1 at uhub1 port 2 configuration 1 interface 1
urndis1: ServerEngines SE USB Device, rev 1.10/0.01, addr 2
urndis1: could not find data bulk in
urndis1: could not find data bulk out
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ipmi0: version 2.0 interface KCS iobase 0xca2/2 spacing 1
cd0: detached
scsibus0: detached
umass0: detached
umass0: at uhub3 port 1 (addr 3) disconnected

--Shawn Novak