Re: wm devices don't work under current amd64

[SAITOH Masanobu <msaitoh%execsw.org@localhost>]

Hi, Tom.

On 2016/03/10 4:12, Tom Ivar Helbekkmo wrote:
> SAITOH Masanobu <msaitoh%execsw.org@localhost> writes:
> 
>>  You mean your machine works with INTx but it doesn't work on MSI, right?
> 
> That is correct.
> 
>> If so, could you show the full dmesg of the machine?
> 
> Appended below.
> 
>>  And, did you test if your machine's problem does occur "without" vlan?
> 
> This is the laptop, which doesn't use vlans.  The other machine, the
> Poweredge 2650, is my main server, and does all its networking over a
> vlan trunk on its wm0 interface.  I suspect that its problem is
> different, since it works with a -current from October 10th, whereas the
> laptop doesn't.
> 
> dmesg output from the laptop after making its wm0 use INTx instead of MSI:

 Thank you for your quick reply. I had two ICH9 motherboard but I discarded
them because both of them were broken... Now I have no any ICH9 machine.
I have some ICH8s and one ICH10. All of them worked, so I had thought that
ICH9 worked.

 I'm sorry that I'm busy because AsiaBSDCon starts today and I'll be absent
the next one week from Tokyo. I would be happy if someone(TM) debug
and test with variety of ICH9 machines.

 Regards.


> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 7.99.26 (DEJAH) #5: Wed Mar  9 17:36:37 CET 2016
> 	root%barsoom.hamartun.priv.no@localhost:/usr/obj/sys/arch/amd64/compile.amd64/DEJAH
> total memory = 4083 MB
> avail memory = 3945 MB
> rnd: seeded with 128 bits
> timecounter: Timecounters tick every 10.000 msec
> Kernelized RAIDframe activated
> timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
> Dell Inc. Latitude E6400                  
> mainbus0 (root)
> cpu0 at mainbus0
> cpu0: Intel(R) Core(TM)2 Duo CPU     T9600  @ 2.80GHz, id 0x1067a
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
> pchb0 at pci0 dev 0 function 0: vendor 8086 product 2a40 (rev. 0x07)
> agp0 at pchb0: can't find internal VGA config space
> ppb0 at pci0 dev 1 function 0: vendor 8086 product 2a41 (rev. 0x07)
> ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x16 @ 2.5GT/s
> pci1 at ppb0 bus 1
> pci1: i/o space, memory space enabled, rd/line, wr/inv ok
> vga0 at pci1 dev 0 function 0: vendor 10de product 06eb (rev. 0xa1)
> wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
> wsmux1: connecting to wsdisplay0
> drm at vga0 not configured
> wm0 at pci0 dev 25 function 0: 82801I mobile (AMT) LAN Controller (rev. 0x03)
> wm0: interrupting at irq 11
> wm0: PCI-Express bus
> wm0: 2048 words FLASH
> wm0: Ethernet address 00:26:b9:cd:21:c2
> makphy0 at wm0 phy 2: Marvell 88E1149 Gigabit PHY, rev. 1
> makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> uhci0 at pci0 dev 26 function 0: vendor 8086 product 2937 (rev. 0x03)
> uhci0: interrupting at irq 10
> usb0 at uhci0: USB revision 1.0
> uhci1 at pci0 dev 26 function 1: vendor 8086 product 2938 (rev. 0x03)
> uhci1: interrupting at irq 3
> usb1 at uhci1: USB revision 1.0
> uhci2 at pci0 dev 26 function 2: vendor 8086 product 2939 (rev. 0x03)
> uhci2: interrupting at irq 11
> usb2 at uhci2: USB revision 1.0
> ehci0 at pci0 dev 26 function 7: vendor 8086 product 293c (rev. 0x03)
> ehci0: interrupting at irq 11
> ehci0: BIOS has given up ownership
> ehci0: EHCI version 1.0
> ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
> usb3 at ehci0: USB revision 2.0
> hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
> hdaudio0: interrupting at irq 3
> hdafg0 at hdaudio0: vendor 111d product 76b2
> hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
> hdafg0: DAC01 2ch: Speaker [Jack]
> hdafg0: DIG02 2ch: SPDIF Out [Jack]
> hdafg0: 2ch/0ch 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
> audio0 at hdafg0: full duplex, playback, capture, mmap, independent
> ppb1 at pci0 dev 28 function 0: vendor 8086 product 2940 (rev. 0x03)
> ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
> pci2 at ppb1 bus 11
> pci2: i/o space, memory space enabled, rd/line, wr/inv ok
> ppb2 at pci0 dev 28 function 1: vendor 8086 product 2942 (rev. 0x03)
> ppb2: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
> pci3 at ppb2 bus 12
> pci3: i/o space, memory space enabled, rd/line, wr/inv ok
> iwn0 at pci3 dev 0 function 0: vendor 8086 product 4235 (rev. 0x00)
> iwn0: interrupting at irq 10
> iwn0: MIMO 3T3R, MoW, address 00:21:6a:ba:79:e2
> iwn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
> iwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> iwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
> ppb3 at pci0 dev 28 function 2: vendor 8086 product 2944 (rev. 0x03)
> ppb3: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
> pci4 at ppb3 bus 13
> pci4: i/o space, memory space enabled, rd/line, wr/inv ok
> ppb4 at pci0 dev 28 function 3: vendor 8086 product 2946 (rev. 0x03)
> ppb4: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
> pci5 at ppb4 bus 14
> pci5: i/o space, memory space enabled, rd/line, wr/inv ok
> uhci3 at pci0 dev 29 function 0: vendor 8086 product 2934 (rev. 0x03)
> uhci3: interrupting at irq 10
> usb4 at uhci3: USB revision 1.0
> uhci4 at pci0 dev 29 function 1: vendor 8086 product 2935 (rev. 0x03)
> uhci4: interrupting at irq 3
> usb5 at uhci4: USB revision 1.0
> uhci5 at pci0 dev 29 function 2: vendor 8086 product 2936 (rev. 0x03)
> uhci5: interrupting at irq 11
> usb6 at uhci5: USB revision 1.0
> ehci1 at pci0 dev 29 function 7: vendor 8086 product 293a (rev. 0x03)
> ehci1: interrupting at irq 10
> ehci1: BIOS refuses to give up ownership, using force
> ehci1: EHCI version 1.0
> ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
> usb7 at ehci1: USB revision 2.0
> ppb5 at pci0 dev 30 function 0: vendor 8086 product 2448 (rev. 0x93)
> pci6 at ppb5 bus 3
> pci6: i/o space, memory space enabled
> fwohci0 at pci6 dev 1 function 0: vendor 1180 product 0832 (rev. 0x04)
> fwohci0: interrupting at irq 10
> fwohci0: OHCI version 1.10 (ROM=0)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 37:4f:c0:00:34:ae:d8:90
> fwohci0: Phy 1394a available S400, 1 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> ieee1394if0 at fwohci0: IEEE1394 bus
> fwip0 at ieee1394if0: IP over IEEE1394
> fwohci0: Initiate bus reset
> sdhc0 at pci6 dev 1 function 1: vendor 1180 product 0822 (rev. 0x21)
> sdhc0: interrupting at irq 11
> sdhc0: SDHC 1.0, rev 4, SDMA, 33000 kHz, HS 3.3V, 512 byte blocks
> sdmmc0 at sdhc0 slot 0
> sdhc1 at pci6 dev 1 function 2: vendor 1180 product 0843 (rev. 0x11)
> sdhc1: interrupting at irq 11
> sdhc1: SDHC 2.0, rev 4, PIOsdhc1: unknown base clock frequency
> sdhc1: couldn't initialize host (0x10)
> ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 2917 (rev. 0x03)
> timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
> ichlpcib0: 24-bit timer
> tco0 at ichlpcib0: TCO (watchdog) timer configured.
> tco0: Min/Max interval 1/367 seconds
> gpio0 at ichlpcib0: 64 pins
> ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 282a (rev. 0x03)
> ahcisata0: interrupting at irq 10
> ahcisata0: 64-bit DMA
> ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP 0xef22ffe3<SXS,EMS,CCCS,PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
> atabus0 at ahcisata0 channel 0
> atabus1 at ahcisata0 channel 1
> atabus2 at ahcisata0 channel 4
> atabus3 at ahcisata0 channel 5
> ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 2930 (rev. 0x03)
> ichsmb0: interrupting at irq 10
> iic0 at ichsmb0: I2C bus
> isa0 at ichlpcib0
> tpm0 at isa0 iomem 0xfed40000-0xfed44fff irq 7: device 0x200114e4 rev 0x30
> com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
> intr_establish_xname: pic pic0 pin 3: can't share type 3 with 2
> pckbc0 at isa0 port 0x60-0x64
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pms0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> attimer0 at isa0 port 0x40-0x43
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: PC speaker
> sysbeep0 at pcppi0
> attimer0: attached to pcppi0
> est0 at cpu0: Enhanced SpeedStep
> coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
> fwohci0: BUS reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
> ieee1394if0: bus manager 0
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
> IPsec: Initialized Security Association Processing.
> uhub0 at usb0: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub1 at usb1: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhub2 at usb2: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhub3 at usb3: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub3: 6 ports with 6 removable, self powered
> uhub4 at usb4: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub4: 2 ports with 2 removable, self powered
> uhub5 at usb5: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub5: 2 ports with 2 removable, self powered
> uhub6 at usb6: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub6: 2 ports with 2 removable, self powered
> uhub7 at usb7: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub7: 6 ports with 6 removable, self powered
> ahcisata0 port 0: device present, speed: 3.0Gb/s
> ahcisata0 port 1: device present, speed: 1.5Gb/s
> ehci0: handing over full speed device on port 5 to uhci2
> wd0 at atabus0 drive 0
> wd0: <ST9250410ASG>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
> wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
> atapibus0 at atabus1: 1 targets
> cd0 at atapibus0 drive 0: <PLDS DVD+/-RW DU-8A3S, 911100494545, KD01> cdrom removable
> cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
> pad0: outputs: 44100Hz, 16-bit, stereo
> audio1 at pad0: half duplex, playback, capture
> boot device: wd0
> root on wd0a dumps on wd0b
> root file system type: ffs
> kern.module.path=/stand/amd64/7.99.26/modules
> cd0(ahcisata0:1:0):  DEFERRED ERROR, key = 0x2
> ugen0 at uhub2 port 1
> ugen0: Broadcom Corp 5880, rev 1.10/1.01, addr 2
> iwn0: scan request(1) while scanning(0) ignored
> wsdisplay0: screen 1 added (80x25, vt100 emulation)
> wsdisplay0: screen 2 added (80x25, vt100 emulation)
> wsdisplay0: screen 3 added (80x25, vt100 emulation)
> wsdisplay0: screen 4 added (80x25, vt100 emulation)
> 
> -tih
> 


-- 
-----------------------------------------------
                SAITOH Masanobu (msaitoh%execsw.org@localhost
                                 msaitoh%netbsd.org@localhost)