Booting HP pavilion dv2000 laptop

To: current-users%NetBSD.org@localhost
Subject: Booting HP pavilion dv2000 laptop
From: "John D. Baker" <jdbaker%mylinuxisp.com@localhost>
Date: Sun, 30 Oct 2016 00:07:52 -0500 (CDT)
I have access to an HP pavilion dv2000 laptop.  It is AMD Turion (64-bit)
with mostly NVIDIA accessories.  It has Linux Mint 17.3 on the local disk
which works quite well (and doesn't use 'systemd'--yay!).

This being the first machine I encountered with NVIDIA video, I was curious
about how well NetBSD-current (7.99.41) would work on it.

The answer is:  not very well at all.

Booting GENERIC hangs when attaching "acpi0".

Booting GENERIC with "-2" to disable ACPI hangs while probing built-in
IDE/ATA/SATA devices (cd0 and wd0).  Touching the POWER button briefly
allows it to continue.  The kernel then panics complaining about
"cnopen: no console".

Booting GENERIC with "-2c" to disable ACPI and drop into userconf
permits disabling the "nouveau*" driver after which the process continues
as above (hangs probing cd0 and wd0 until power button is pressed).
Booting then completes.

To be more specific, when the kernel hangs probing "cd0" pressing any
key on the keyboard will allow it to continue.  When it then hangs while
probing "wd0" only touching the power button will unwedge it.  If one
touches the power button when it hangs probing "cd0", it will not hang
when probing "wd0" and complete booting.

Below is "dmesg.boot" following booting GENERIC with "-2c", disabling
"nouveau*" and coaxing it through the IDE device probes with the power
button:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.41 (GENERIC) #34: Sat Oct 29 19:42:45 CDT 2016
	sysop%yggdrasil.technoskunk.fur@localhost:/r0/build/current/obj/amd64/sys/arch/amd64/compile/GENERIC
total memory = 1982 MB
avail memory = 1904 MB
WARNING: module error: module `nfs' pushed by boot loader already exists
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
userconf: configure system autoconfiguration:
uc> disable nouveau
[340] nouveau* disabled
uc> exit
Continuing...
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP Pavilion dv2000 (GA536UA#ABA) (F.34)
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (nVIDIA   C51-MCP51   )
cpu0 at mainbus0 apid 0
cpu0: AMD Turion(tm) 64 X2 , id 0x40f82
cpu1 at mainbus0 apid 1
cpu1: AMD Turion(tm) 64 X2 , id 0x40f82
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 5 is type PCI   
mpbios: bus 6 is type ISA   
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
NVIDIA C51 Host Bridge (0x02f0) (RAM memory, revision 0xa2) at pci0 dev 0 function 0 not configured
NVIDIA C51 Memory Controller 0 (RAM memory, revision 0xa2) at pci0 dev 0 function 1 not configured
NVIDIA C51 Memory Controller 1 (RAM memory, revision 0xa2) at pci0 dev 0 function 2 not configured
NVIDIA C51 Memory Controller 5 (RAM memory, revision 0xa2) at pci0 dev 0 function 3 not configured
NVIDIA C51 Memory Controller 4 (RAM memory, revision 0xa2) at pci0 dev 0 function 4 not configured
Skipping broken PCI header on 0:0:5
Skipping broken PCI header on 0:0:5
NVIDIA C51 Host Bridge (0x02ff) (RAM memory, revision 0xa2) at pci0 dev 0 function 5 not configured
NVIDIA C51 Memory Controller 3 (RAM memory, revision 0xa2) at pci0 dev 0 function 6 not configured
NVIDIA C51 Memory Controller 2 (RAM memory, revision 0xa2) at pci0 dev 0 function 7 not configured
ppb0 at pci0 dev 2 function 0: NVIDIA C51 PCI Express Bridge (0x02fc) (rev. 0xa1)
ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
bwi0 at pci1 dev 0 function 0: Broadcom Wireless
bwi0: interrupting at ioapic0 pin 11
bwi0: BBP id 0x4311, BBP rev 0x2, BBP pkg 0
bwi0: MAC rev 13 is not supported
bwi0: no MAC was found
ppb1 at pci0 dev 3 function 0: NVIDIA C51 PCI Express Bridge (0x02fd) (rev. 0xa1)
ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci2 at ppb1 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci0 dev 5 function 0: NVIDIA product 0244 (rev. 0xa2)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
NVIDIA nForce430 Host Bridge (RAM memory, revision 0xa2) at pci0 dev 9 function 0 not configured
pcib0 at pci0 dev 10 function 0: NVIDIA nForce430 PCI-ISA Bridge (rev. 0xa3)
nfsmbc0 at pci0 dev 10 function 1: NVIDIA nForce430 SMBus Controller (rev. 0xa3)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
NVIDIA product 0271 (Co-processor processor, revision 0xa3) at pci0 dev 10 function 3 not configured
ohci0 at pci0 dev 11 function 0: NVIDIA nForce430 USB Controller (rev. 0xa3)
ohci0: interrupting at ioapic0 pin 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 11 function 1: NVIDIA nForce430 USB2 Controller (rev. 0xa3)
ehci0: interrupting at ioapic0 pin 7
ehci0: BIOS refuses to give up ownership, using force
ehci0: EHCI version 1.0
ehci0: companion controller, 8 ports each: ohci0
usb1 at ehci0: USB revision 2.0
viaide0 at pci0 dev 13 function 0: NVIDIA nForce430 IDE Controller (rev. 0xf1)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 14 function 0: NVIDIA nForce430 Serial ATA Controller (rev. 0xf1)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
viaide1: using ioapic0 pin 5 for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
ppb2 at pci0 dev 16 function 0: NVIDIA nForce430 PCI-PCI Bridge (rev. 0xa2)
pci3 at ppb2 bus 5
pci3: i/o space, memory space enabled
fwohci0 at pci3 dev 9 function 0: Ricoh 5C832 PCI-SD/MMC/MMC+/MS/xD/Firewire (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 10
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 xx:xx:xx:xx:xx:xx:xx:xx
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
sdhc0 at pci3 dev 9 function 1: Ricoh 5C822 PCI-CardBus Bridge/MS/SD/MMC/SC (rev. 0x19)
sdhc0: interrupting at ioapic0 pin 10
sdhc0: SDHC 1.0, rev 2, SDMA, 33000 kHz, 3.3V, 512 byte blocks
sdmmc0 at sdhc0 slot 0
Ricoh 5C843 PCI-CardBus Bridge/SD/MMC/MMC+/MS/xD/Firewire (miscellaneous system, revision 0x01) at pci3 dev 9 function 2 not configured
Ricoh 5C592 PCI-CardBus Bridge/MS/SD/Firewire (miscellaneous system, revision 0x0a) at pci3 dev 9 function 3 not configured
Ricoh xD-Picture Card Controller (miscellaneous system, revision 0x05) at pci3 dev 9 function 4 not configured
hdaudio0 at pci0 dev 16 function 1: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 10
hdafg0 at hdaudio0: vendor 14f1 product 5045
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: DIG01 2ch: SPDIF Out [Jack]
hdafg0: ADC02 2ch: Mic In [Built-In]
hdafg0: 2ch/2ch 48000Hz 96000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdvsmfg at hdaudio0 not configured
nfe0 at pci0 dev 20 function 0: NVIDIA nForce430 Gigabit Ethernet Controller (rev. 0xa3)
nfe0: interrupting at ioapic0 pin 11
nfe0: Ethernet address xx:xx:xx:xx:xx:xx
ukphy0 at nfe0 phy 1: Marvell 88E1118 Gigabit PHY (OUI 0x000ac2, model 0x0022), rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pchb0 at pci0 dev 24 function 0: AMD K8 AMD64 HyperTransport Configuration (rev. 0x00)
pchb1 at pci0 dev 24 function 1: AMD K8 AMD64 Address Map Configuration (rev. 0x00)
pchb2 at pci0 dev 24 function 2: AMD K8 AMD64 DRAM Configuration (rev. 0x00)
amdnb_misc0 at pci0 dev 24 function 3: AMD NB Misc Configuration
amdtemp0 at amdnb_misc0: AMD CPU Temperature Sensors (K8: core rev BH-F2, socket S1)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Palm detect, Two button click pad, Multi-finger
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer0: attached to pcppi0
powernow0 at cpu0: failed to initialize (err 6)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
atapibus0 at atabus1: 2 targets
IPsec: Initialized Security Association Processing.
uhub0 at usb1: NVIDIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
uhub1 at usb0: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T20L, KYC76KA5521, NC08> cdrom removable
[hangs here until key/power-button pressed]
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
viaide1 port 0: device present, speed: 1.5Gb/s
wd0 at atabus2 drive 0
wd0: <FUJITSU MHV2080BH>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[hangs here if key other than power-button pressed for "cd0", requires power
button press to continue]
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uvideo0 at uhub0 port 8 configuration 1 interface 0: Sonix Technology Co., Ltd. USB 2.0 Camera, rev 2.00/2.10, addr 2
video0 at uvideo0: Sonix Technology Co., Ltd. USB 2.0 Camera, rev 2.00/2.10, addr 2
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
WARNING: 2 errors while detecting hardware; check system log.
boot device: nfe0
root on nfe0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: q.r.s.t
nfs_boot: my_name=dpe2850e
nfs_boot: my_domain=technoskunk.fur
nfs_boot: my_addr=a.b.c.d
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=l.m.n.o
root on q.r.s.t:/r0/diskless/dpe2850e
root file system type: nfs
kern.module.path=/stand/amd64/7.99.41/modules
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

-- 
|/"\ John D. Baker, KN5UKS               NetBSD     Darwin/MacOS X
|\ / jdbaker[snail]mylinuxisp[flyspeck]com    OpenBSD            FreeBSD
| X  No HTML/proprietary data in email.   BSD just sits there and works!
|/ \ GPGkeyID:  D703 4A7E 479F 63F8 D3F4  BD99 9572 8F23 E4AD 1645
Follow-Ups:
- Re: Booting HP pavilion dv2000 laptop
  - From: John D. Baker
- Re: Booting HP pavilion dv2000 laptop
  - From: Michael van Elst
Prev by Date: daily CVS update output
Next by Date: Re: ffs_newvnode: inode has non zero blocks
Previous by Thread: ffs_newvnode: inode has non zero blocks
Next by Thread: Re: Booting HP pavilion dv2000 laptop
Indexes:
Home | Main Index | Thread Index | Old Index