Subject: kern/13198: FlexPort 8S hangs NetBSD
To: None <gnats-bugs@gnats.netbsd.org>
From: None <nigel@nelgin.nu>
List: netbsd-bugs
Date: 06/14/2001 00:21:59
>Number: 13198
>Category: kern
>Synopsis: FlexPort 8S hangs NetBSD
>Confidential: no
>Severity: critical
>Priority: high
>Responsible: kern-bug-people
>State: open
>Class: sw-bug
>Submitter-Id: net
>Arrival-Date: Wed Jun 13 17:25:00 PDT 2001
>Closed-Date:
>Last-Modified:
>Originator: Nigel Reed
>Release: 1.5.1_ALPHA, 1.5.1_BETA2, NetBSD 1.5V
>Organization:
>Environment:
System: NetBSD c643704-b 1.5V NetBSD 1.5V (WIBBLE) #3: Sat May 19 18:51:49 CDT 2001 nigel@c643704-b:/usr/current/src/sys/arch/i386/compile/WIBBLE i386
>Description:
This was originally reported in port-i386 but they seem incapable of fixing
it.
port-i386/12860
I installed an ISA FlexPort 8S into a system (Celeron 533 with 128megs).
The device is set to irq 5, nothing else uses irq 5. The IO port is left
at factory settings (jumper is open). dmesg reports the device is found and
allocates the com devices, however when I "echo hello > /dev/tty03" the
system locks solid. Telnet sessions are dropped, the console hangs.
I also tried this on 1.5.1_ALPHA with the same results.
NetBSD 1.5.1_BETA (WIBBLE) #2: Sun May 6 20:04:40 CDT 2001
nigel@c643704-b:/usr/src/sys/arch/i386/compile/WIBBLE
cpu0: Intel Celeron (Mendocino) (686-class), 534.59 MHz
total memory = 127 MB
avail memory = 115 MB
using 1659 buffers containing 6636 KB of memory
BIOS32 rev. 0 found at 0xfaff0
PCI BIOS rev. 2.1 found at 0xfb020
PCI IRQ Routing Table rev. 1.0 found at 0xfdae0, size 144 bytes (7 entries)
PCI Interrupt Router at 000:07:0 (vendor 0x1106 product 0x0596)
PCI Exclusive IRQs: 10 11
mainbus0 (root)
pnpbios0 at mainbus0: nodes 13, max len 74
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1106 product 0x0691 (rev. 0xc4)
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0x8598 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x1106 product 0x0686 (rev. 0x22)
pciide0 at pci0 dev 7 function 1: VIA Tech VT82C586A IDE Controller (rev. 0x10)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 1: <QUANTUM FIREBALLP AS30.0>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 28629 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 58633344 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: secondary channel configured to compatibility mode
pciide0: disabling secondary channel (no drives)
uhci0 at pci0 dev 7 function 2: vendor 0x1106 product 0x3038 (rev. 0x10)
pci_intr_map: no mapping for pin D
uhci0: couldn't map interrupt
uhci1 at pci0 dev 7 function 3: vendor 0x1106 product 0x3038 (rev. 0x10)
pci_intr_map: no mapping for pin D
uhci1: couldn't map interrupt
pchb1 at pci0 dev 7 function 4
pchb1: vendor 0x1106 product 0x3057 (rev. 0x30)
vga0 at pci0 dev 8 function 0: vendor 0x102b product 0x0519 (rev. 0x01)
wsdisplay0 at vga0: console (80x25, vt100 emulation)
wsdisplay0: screen 1-4 added (80x25, vt100 emulation)
de0 at pci0 dev 10 function 0
de0: interrupting at irq 10
de0: DEC DE500-XA 21140 [10-100Mb/s] pass 1.2
de0: address 00:00:f8:02:8d:54
siop0 at pci0 dev 11 function 0: Symbios Logic 53c825 (fast wide scsi)
siop0: interrupting at irq 11
scsibus0 at siop0: 16 targets, 8 luns per target
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
addcom0 at isa0 port 0x108-0x147 irq 5
com2 at addcom0 slave 0: ns16550a, working fifo
com3 at addcom0 slave 1: ns16550a, working fifo
com4 at addcom0 slave 2: ns16550a, working fifo
com5 at addcom0 slave 3: ns16550a, working fifo
com6 at addcom0 slave 4: ns16550a, working fifo
com7 at addcom0 slave 5: ns16550a, working fifo
com8 at addcom0 slave 6: ns16550a, working fifo
com9 at addcom0 slave 7: ns16550a, working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask fb5d netmask ff5d ttymask ffdf
scsibus0: waiting 2 seconds for devices to settle...
cd0 at scsibus0 target 0 lun 0: <NEC, CD-ROM DRIVE:500, 1.0> SCSI2 5/cdrom removable
de0: enabling 10baseT port
siop0: target 6 using tagged queuing
st0 at scsibus0 target 6 lun 0: <EXABYTE, EXB-8200, 2618> SCSI1 1/sequential removable
st0: siop0: target 6 using 8bit transfers
siop0: target 6 asynchronous
drive empty
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
IP Filter: v3.4.9 initialized. Default = pass all, Logging = enabled
wsmux1: connecting to wsdisplay0
# $NetBSD: GENERIC,v 1.354.2.9 2000/12/12 21:28:24 he Exp $
#
# GENERIC -- everything that's currently supported
#
include "arch/i386/conf/std.i386"
#ident "GENERIC-$Revision: 1.354.2.9 $"
maxusers 32 # estimated number of users
# CPU support. At least one is REQUIRED.
#options I386_CPU
#options I486_CPU
#options I586_CPU
options I686_CPU
# CPU-related options.
options MATH_EMULATE # floating point emulation
options VM86 # virtual 8086 emulation
options USER_LDT # user-settable LDT; used by WINE
# eliminate delay no-ops in I/O; recommended on all but very old machines
options DUMMY_NOPS
# delay between "rebooting ..." message and hardware reset, in milliseconds
#options CPURESET_DELAY=2000
# This option allows you to force a serial console at the specified
# I/O address. see console(4) for details.
#options "CONSDEVNAME=\"com\"",CONADDR=0x2f8,CONSPEED=57600
# you don't want the option below ON iff you are using the
# serial console option of the new boot strap code.
#options CONS_OVERRIDE # Always use above! independent of boot info
# The following options override the memory sizes passed in from the boot
# block. Use them *only* if the boot block is unable to determine the correct
# values. Note that the BIOS may *correctly* report less than 640k of base
# memory if the extended BIOS data area is located at the top of base memory
# (as is the case on most recent systems).
#options REALBASEMEM=639 # size of base memory (in KB)
#options REALEXTMEM=15360 # size of extended memory (in KB)
# Standard system options
options UCONSOLE # users can use TIOCCONS (for xconsole)
options INSECURE # disable kernel security levels
options RTC_OFFSET=360 # hardware clock is this many mins. west of GMT
options NTP # NTP phase/frequency locked loop
options KTRACE # system call tracing via ktrace(1)
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
options SYSVSHM # System V-like memory sharing
#options SHMMAXPGS=1024 # 1024 pages is the default
options LKM # loadable kernel modules
# Diagnostic/debugging support options
options DIAGNOSTIC # cheap kernel consistency checks
#options DEBUG # expensive debugging checks/support
options KMEMSTATS # kernel memory statistics (vmstat -m)
options DDB # in-kernel debugger
options DDB_HISTORY_SIZE=512 # enable history editing in DDB
#options KGDB # remote debugger
#options "KGDB_DEVNAME=\"com\"",KGDBADDR=0x3f8,KGDBRATE=9600
makeoptions DEBUG="-g" # compile full symbol table
# Compatibility options
#options COMPAT_NOMID # compatibility with 386BSD, BSDI, NetBSD 0.8,
#options COMPAT_09 # NetBSD 0.9,
#options COMPAT_10 # NetBSD 1.0,
#options COMPAT_11 # NetBSD 1.1,
#options COMPAT_12 # NetBSD 1.2,
#options COMPAT_13 # NetBSD 1.3,
#options COMPAT_14 # NetBSD 1.4,
#options COMPAT_43 # and 4.3BSD
#options COMPAT_386BSD_MBRPART # recognize old partition ID
options COMPAT_SVR4 # binary compatibility with SVR4
options COMPAT_IBCS2 # binary compatibility with SCO and ISC
options COMPAT_LINUX # binary compatibility with Linux
options COMPAT_FREEBSD # binary compatibility with FreeBSD
options COMPAT_PECOFF # kernel support to run Win32 apps
# File systems
file-system FFS # UFS
#file-system EXT2FS # second extended file system (linux)
#file-system LFS # log-structured file system
#file-system MFS # memory file system
file-system NFS # Network File System client
#file-system NTFS # Windows/NT file system (experimental)
file-system CD9660 # ISO 9660 + Rock Ridge file system
#file-system MSDOSFS # MS-DOS file system
file-system FDESC # /dev/fd
file-system KERNFS # /kern
#file-system NULLFS # loopback file system
#file-system OVERLAY # overlay file system
#file-system PORTAL # portal filesystem (still experimental)
file-system PROCFS # /proc
#file-system UMAPFS # NULLFS + uid and gid remapping
#file-system UNION # union file system
#file-system CODA # Coda File System; also needs vcoda (below)
# File system options
#options QUOTA # UFS quotas
#options FFS_EI # FFS Endian Independent support
#options SOFTDEP # FFS soft updates support.
options NFSSERVER # Network File System server
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
# immutable) behave as system flags.
# Networking options
#options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPV6
#options IPSEC # IP security
#options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
#options IPSEC_DEBUG # debug for IP security
#options MROUTING # IP multicast routing
#options NS # XNS
#options NSIP # XNS tunneling over IP
#options ISO,TPIP # OSI
#options EON # OSI tunneling over IP
#options CCITT,LLC,HDLC # X.25
#options NETATALK # AppleTalk networking protocols
#options PPP_BSDCOMP # BSD-Compress compression support for PPP
#options PPP_DEFLATE # Deflate compression support for PPP
#options PPP_FILTER # Active filter support for PPP (requires bpf)
options PFIL_HOOKS # pfil(9) packet filter hooks
options IPFILTER_LOG # ipmon(8) log support
# Compatibility with 4.2BSD implementation of TCP/IP. Not recommended.
#options TCP_COMPAT_42
# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
#options EISAVERBOSE # verbose EISA device autoconfig messages
#options MIIVERBOSE # verbose PHY autoconfig messages
#options PCIVERBOSE # verbose PCI device autoconfig messages
#options PCI_CONFIG_DUMP # verbosely dump PCI config space
##options PCMCIAVERBOSE # verbose PCMCIA configuration messages
#options SCSIVERBOSE # human readable SCSI error messages
#options USBVERBOSE # verbose USB device autoconfig messages
#options PNPBIOSVERBOSE # verbose PnP BIOS messages
#options PNPBIOSDEBUG # more fullsome Pnp BIOS debugging messages
#options NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM
#
# wscons options
#
# builtin terminal emulations
#options WSEMUL_SUN # sun terminal emulation
options WSEMUL_VT100 # VT100 / VT220 emulation
# different kernel output - see dev/wscons/wsdisplayvar.h
options WS_KERNEL_FG=WSCOL_GREEN
#options WS_KERNEL_BG=WSCOL_BLACK
# compatibility to other console drivers
options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
options WSDISPLAY_COMPAT_USL # VT handling
options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
# see dev/pckbc/wskbdmap_mfii.c for implemented layouts
#options PCKBD_LAYOUT="(KB_DE | KB_NODEAD)"
# allocate a number of virtual screens at autoconfiguration time
options WSDISPLAY_DEFAULTSCREENS=5
# use a large software cursor that doesn't blink
options PCDISPLAY_SOFTCURSOR
# Kernel root file system and dump configuration.
config netbsd root on ? type ?
#config netbsd root on sd0a type ffs
#config netbsd root on ? type nfs
#
# Device configuration
#
mainbus0 at root
#apm0 at mainbus0 # Advanced power management
# Tuning for power management, see apm(4) for more details.
#options APM_NO_IDLE # Don't call BIOS CPU idle function
#options APM_V10_ONLY # Use only the APM 1.0 calls
#options APM_NO_POWEROFF # Don't power off on halt(8)
#options APM_POWER_PRINT # Print stats on the console
#options APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts
# Basic Bus Support
# Plug-and-Play BIOS and attached devices
pnpbios* at mainbus?
# mainboard audio chips
#ess* at pnpbios? index ? # ESS AudioDrive
#sb* at pnpbios? index ? # NeoMagic 256AV in sb mode
#wss* at pnpbios? index ? # NeoMagic 256AV in wss mode
#ym* at pnpbios? index ? # OPL3-SA3
# com port
# If enabled, consider changing "com0", "com1", and "com2" under "ISA Serial
# Interfaces" to "com*", otherwise com2 will attach at pnpbios? and there
# will be no com0. A side effect is pcmcia (and other) com? previously
# starting at com3 may attach as com1 or com2.
#com* at pnpbios? index ? # serial ports
# parallel port
# The above "com*" comments apply, cf. "lpt0" under "ISA parallel
# "printer interfaces".
#lpt* at pnpbios? index ? # parallel ports
#pckbc* at pnpbios? index ? # PC keyboard/mouse controller
#fdc* at pnpbios? index ? # floppy controller
# IDE controller on Toshiba Portege 3000 series (crippled PCI device)
#pciide* at pnpbios? index ?
# PCI bus support
pci* at mainbus? bus ?
pci* at pchb? bus ?
pci* at ppb? bus ?
# Configure PCI using BIOS information
options PCIBIOS # PCI BIOS support
#options PCIBIOSVERBOSE # PCI BIOS verbose info
#options PCIBIOS_ADDR_FIXUP # fixup PCI I/O addresses
#options PCIBIOS_BUS_FIXUP # fixup PCI bus numbering
#options PCIBIOS_INTR_FIXUP # fixup PCI interrupt routing
#options PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or 11
#options PCIBIOS_INTR_GUESS # see pcibios(4)
#options PCIINTR_DEBUG # super-verbose PCI interrupt fixup
# PCI bridges
pchb* at pci? dev ? function ? # PCI-Host bridges
#pceb* at pci? dev ? function ? # PCI-EISA bridges
pcib* at pci? dev ? function ? # PCI-ISA bridges
ppb* at pci? dev ? function ? # PCI-PCI bridges
# XXX 'puc's aren't really bridges, but there's no better place for them here
#puc* at pci? dev ? function ? # PCI "universal" comm. cards
# EISA bus support
#eisa* at mainbus?
#eisa* at pceb?
# ISA bus support
#isa* at mainbus?
#isa* at pceb?
isa* at pcib?
# PCMCIA bus support
#pcmcia* at pcic? controller ? socket ?
#pcmcia* at tcic? controller ? socket ?
# ISA PCMCIA controllers
#pcic0 at isa? port 0x3e0 iomem 0xd0000 iosiz 0x10000
#pcic1 at isa? port 0x3e2 iomem 0xe0000 iosiz 0x4000
#tcic0 at isa? port 0x240 iomem 0xd0000 iosiz 0x10000
# PCI PCMCIA controllers
#pcic0 at pci? dev? function ?
# ISA Plug-and-Play bus support
isapnp0 at isa?
# ISA Plug-and-Play PCMCIA controllers
#pcic* at isapnp?
# CardBus bridge support
#cbb* at pci? dev ? function ?
#cardslot* at cbb?
# CardBus bus support
#cardbus* at cardslot?
#pcmcia* at cardslot?
# Coprocessor Support
# Math Coprocessor support
npx0 at isa? port 0xf0 irq 13 # x86 math coprocessor
# Console Devices
# ISA console
#pc0 at isa? port 0x60 irq 1 # pccons generic PC console driver
# Keyboard layout configuration for pccons
#options FRENCH_KBD
#options FINNISH_KBD
#options GERMAN_KBD
#options NORWEGIAN_KBD
# pccons-specific options:
#options XSERVER_DDB # PF12 gets you into DDB when X is running
#options XSERVER # X server support
# wscons
pckbc0 at isa? # pc keyboard controller
pckbd* at pckbc? # PC keyboard
# "opms" should not be enabled together with "pms" or "pmsi"
#pms* at pckbc? # PS/2 mouse for wsmouse
pmsi* at pckbc? # PS/2 "Intelli"mouse for wsmouse
#opms* at pckbc? # backwards compatible PS/2 mouse
#vga0 at isa?
vga* at pci? dev ? function ?
#pcdisplay0 at isa? # CGA, MDA, EGA, HGA
wsdisplay* at vga? console ?
#wsdisplay* at pcdisplay? console ?
wskbd* at pckbd? console ?
#wsmouse* at pms? mux 0
wsmouse* at pmsi? mux 0
pcppi0 at isa?
sysbeep0 at pcppi?
# Serial Devices
# PCI serial interfaces
#com* at puc? port ? # 16x50s on "universal" comm boards
#cy* at pci? dev ? function ? # Cyclades Cyclom-Y serial boards
#cz* at pci? dev ? function ? # Cyclades-Z multi-port serial boards
# ISA Plug-and-Play serial interfaces
com* at isapnp? # Modems and serial boards
# PCMCIA serial interfaces
#com* at pcmcia? function ? # Modems and serial cards
#pcmcom* at pcmcia? function ? # PCMCIA multi-port serial cards
#com* at pcmcom? slave ? # ...and the slave devices
# CardBus serial interfaces
#com* at cardbus? function ? # Modems and serial cards
# ISA serial interfaces
#options COM_HAYESP # adds Hayes ESP serial board support
com0 at isa? port 0x3f8 irq 4 # Standard PC serial ports
com1 at isa? port 0x2f8 irq 3
#com2 at isa? port 0x3e8 irq 5
#com3 at isa? port 0x2e8 irq 9
#ast0 at isa? port 0x1a0 irq 5 # AST 4-port serial cards
#com* at ast? slave ?
#boca0 at isa? port 0x100 irq 5 # BOCA 8-port serial cards
#boca0 at isa? port 0x100 irq 5 # BOCA 16-port serial cards (BB2016)
#boca1 at isa? port 0x140 irq 5 # this line is also needed for BB2016
#com* at boca? slave ?
#tcom0 at isa? port 0x100 irq 7 # TC-800 8-port serial cards
#com* at tcom? slave ?
#rtfps0 at isa? port 0x1230 irq 10 # RT 4-port serial cards
#com* at rtfps? slave ?
#cy0 at isa? iomem 0xd4000 irq 12 # Cyclades serial cards
addcom0 at isa? port 0x108 irq 5 # Addonics FlexPort 8S
com* at addcom? slave ?
# Parallel Printer Interfaces
# PCI parallel printer interfaces
#lpt* at puc? port ? # || ports on "universal" comm boards
# ISA parallel printer interfaces
lpt0 at isa? port 0x378 irq 7 # standard PC parallel ports
#lpt1 at isa? port 0x278
#lpt2 at isa? port 0x3bc
# LM7[89] and compatible hardware monitors
#lm0 at isa? port 0x290 # other common ports: 0x280, 0x310
# VIA VT82C686A hardware monitor
#viapm* at pci? dev ? function ?
#viaenv* at viapm?
# SCSI Controllers and Devices
# PCI SCSI controllers
#adv* at pci? dev ? function ? # AdvanSys 1200[A,B], 9xx[U,UA] SCSI
#adw* at pci? dev ? function ? # AdvanSys 9x0UW[D], 3940U[2,3]W SCSI
#ahc* at pci? dev ? function ? # Adaptec [23]94x, aic78x0 SCSI
#bha* at pci? dev ? function ? # BusLogic 9xx SCSI
#dpt* at pci? dev ? function ? # DPT SmartCache/SmartRAID
#isp* at pci? dev ? function ? # Qlogic ISP [12]0x0 SCSI/FibreChannel
#ncr* at pci? dev ? function ? # NCR 53c8xx SCSI (old driver)
siop* at pci? dev ? function ? # Symbios 53c8xx SCSI
#pcscp* at pci? dev ? function ? # AMD 53c974 PCscsi-PCI SCSI
# EISA SCSI controllers
#ahb* at eisa? slot ? # Adaptec 174[02] SCSI
#ahc* at eisa? slot ? # Adaptec 274x, aic7770 SCSI
#bha* at eisa? slot ? # BusLogic 7xx SCSI
#dpt* at eisa? slot ? # DPT EATA SCSI
#uha* at eisa? slot ? # UltraStor 24f SCSI
# PCMCIA SCSI controllers
#aic* at pcmcia? function ? # Adaptec APA-1460 SCSI
#esp* at pcmcia? function ? # Qlogic ESP406/FAS408 SCSI
# ISA Plug-and-Play SCSI controllers
#aha* at isapnp? # Adaptec AHA-154[02
#aic* at isapnp? # Adaptec AHA-1520B
# ISA SCSI controllers
#adv0 at isa? port ? irq ? drq ? # AdvanSys APB-514[02]
#aha0 at isa? port 0x330 irq ? drq ? # Adaptec 154[02] SCSI
#aha1 at isa? port 0x334 irq ? drq ?
#ahc0 at isa? port ? irq ? # Adaptec 284x SCSI
#aic0 at isa? port 0x340 irq 11 # Adaptec 152[02] SCSI
#bha0 at isa? port 0x330 irq ? drq ? # BusLogic [457]4X SCSI
#bha1 at isa? port 0x334 irq ? drq ?
## The "nca" and "dpt" probes might give false hits or hang your machine.
#dpt0 at isa? port 0x170 irq ? drq ? # DPT SmartCache/SmartRAID
#nca0 at isa? port 0x360 irq 15 # Port-mapped NCR 53C80 contoller
#nca1 at isa? iomem 0xd8000 irq 5 # Memory-mapped controller (T128, etc.)
#sea0 at isa? iomem 0xc8000 irq 5 # Seagate/Future Domain SCSI
#uha0 at isa? port 0x330 irq ? drq ? # UltraStor [13]4f SCSI
#uha1 at isa? port 0x340 irq ? drq ?
#wds0 at isa? port 0x350 irq 15 drq 6 # WD7000 and TMC-7000 controllers
#wds1 at isa? port 0x358 irq 11 drq 5
# CardBus SCSI cards
#ahc* at cardbus? dev ? function ? # Adaptec ADP-1480
# SCSI bus support
#scsibus* at adv?
#scsibus* at adw?
#scsibus* at aha?
#scsibus* at ahb?
#scsibus* at ahc?
#scsibus* at aic?
#scsibus* at bha?
#scsibus* at dpt?
#scsibus* at esp?
#scsibus* at isp?
##scsibus* at nca?
##scsibus* at ncr?
#scsibus* at pcscp?
#scsibus* at sea?
scsibus* at siop?
#scsibus* at uha?
#scsibus* at wds?
#
# SCSI devices
#sd* at scsibus? target ? lun ? # SCSI disk drives
st* at scsibus? target ? lun ? # SCSI tape drives
cd* at scsibus? target ? lun ? # SCSI CD-ROM drives
#ch* at scsibus? target ? lun ? # SCSI autochangers
#ses* at scsibus? target ? lun ? # SCSI Enclosure Services devices
#ss* at scsibus? target ? lun ? # SCSI scanners
#uk* at scsibus? target ? lun ? # SCSI unknown
# RAID controllers and devices
#cac* at pci? dev ? function ? # Compaq array controller
#ca* at cac? unit ? # Compaq array disk device
# IDE and related devices
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
pciide* at pci? dev ? function ? flags 0x0000
# ISA Plug-and-Play IDE controllers
wdc* at isapnp?
# PCMCIA IDE controllers
#wdc* at pcmcia? function ?
# ISA ST506, ESDI, and IDE controllers
# Use flags 0x01 if you want to try to use 32bits data I/O (the driver will
# fall back to 16bits I/O if 32bits I/O are not functional).
# Some controllers pass the initial 32bit test, but will fail later.
#wdc0 at isa? port 0x1f0 irq 14 flags 0x00
#wdc1 at isa? port 0x170 irq 15 flags 0x00
# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
#wd* at wdc? channel ? drive ? flags 0x0000
wd* at pciide? channel ? drive ? flags 0x0000
# ATAPI bus support
#atapibus* at wdc? channel ?
#atapibus* at pciide? channel ?
# ATAPI devices
# flags have the same meaning as for IDE drives.
#cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
#sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
#uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
# Miscellaneous mass storage devices
# ISA floppy
fdc0 at isa? port 0x3f0 irq 6 drq 2 # standard PC floppy controllers
#fdc1 at isa? port 0x370 irq ? drq ?
fd* at fdc? drive ? # the drives themselves
# some machines need you to do this instead of fd*
#fd0 at fdc0 drive 0
# ISA CD-ROM devices
#mcd0 at isa? port 0x300 irq 10 # Mitsumi CD-ROM drives
# ISA tape devices
# note: the wt driver conflicts unpleasantly with SMC boards at the
# same I/O address. The probe reprograms their EEPROMs. Don't
# uncomment it unless you are actually using it.
#wt0 at isa? port 0x308 irq 5 drq 1 # Archive and Wangtek QIC tape drives
# Network Interfaces
# PCI network interfaces
de* at pci? dev ? function ? # DEC 21x4x-based Ethernet
#en* at pci? dev ? function ? # ENI/Adaptec ATM
#ep* at pci? dev ? function ? # 3Com 3c59x
#ex* at pci? dev ? function ? # 3Com 90x[B]
#epic* at pci? dev ? function ? # SMC EPIC/100 Ethernet
#esh* at pci? dev ? function ? # Essential HIPPI card
#fpa* at pci? dev ? function ? # DEC DEFPA FDDI
#fxp* at pci? dev ? function ? # Intel EtherExpress PRO 10+/100B
#le* at pci? dev ? function ? # PCnet-PCI Ethernet
#lmc* at pci? dev ? function ? # Lan Media Corp SSI/HSSI/DS3
#ne* at pci? dev ? function ? # NE2000-compatible Ethernet
#ntwoc* at pci? dev ? function ? # Riscom/N2 PCI Sync Serial
#rtk* at pci? dev ? function ? # Realtek 8129/8139
#sip* at pci? dev ? function ? # SiS 900 Ethernet
#ti* at pci? dev ? function ? # Alteon ACEnic gigabit Ethernet
#tl* at pci? dev ? function ? # ThunderLAN-based Ethernet
#tlp* at pci? dev ? function ? # DECchip 21x4x (and clones) Ethernet
#options TLP_MATCH_21040
#options TLP_MATCH_21041
#options TLP_MATCH_21140
#options TLP_MATCH_21142
#vr* at pci? dev ? function ? # VIA Rhine Fast Ethernet
# EISA network interfaces
#ep* at eisa? slot ? # 3Com 3c579 Ethernet
#fea* at eisa? slot ? # DEC DEFEA FDDI
#tlp* at eisa? slot ? # DEC DE-425 Ethernet
# ISA Plug-and-Play network interfaces
#ep* at isapnp? # 3Com 3c509 Ethernet
#ne* at isapnp? # NE2000-compatible Ethernet
#tr* at isapnp? # IBM/3COM TROPIC Token-Ring
# PCMCIA network interfaces
#an* at pcmcia? function ? # Aironet PC4500/PC4800 (802.11)
#awi* at pcmcia? function ? # BayStack 650/660 (802.11FH/DS)
#cnw* at pcmcia? function ? # Xircom/Netwave AirSurfer
#ep* at pcmcia? function ? # 3Com 3c589 and 3c562 Ethernet
#mbe* at pcmcia? function ? # MB8696x based Ethernet
#ne* at pcmcia? function ? # NE2000-compatible Ethernet
#ray* at pcmcia? function ? # Raytheon Raylink (802.11)
#sm* at pcmcia? function ? # Megahertz Ethernet
#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11)
#xi* at pcmcia? function ? # Xircom CreditCard Ethernet
#mhzc* at pcmcia? function ? # Megahertz Ethernet/Modem combo cards
#com* at mhzc?
#sm* at mhzc?
# ISA network interfaces
#ate0 at isa? port 0x2a0 irq ? # AT1700
#cs0 at isa? port 0x300 iomem ? irq ? drq ? # CS8900 Ethernet
#ec0 at isa? port 0x250 iomem 0xd8000 irq 9 # 3Com 3c503 Ethernet
#eg0 at isa? port 0x280 irq 9 # 3C505 ethernet cards
#el0 at isa? port 0x300 irq 9 # 3C501 ethernet cards
#ep* at isa? port ? irq ? # 3C509 ethernet cards
#ef0 at isa? port 0x360 iomem 0xd0000 irq 7 # 3C507
#ai0 at isa? port 0x360 iomem 0xd0000 irq 7 # StarLAN
#fmv0 at isa? port 0x2a0 irq ? # FMV-180 series
#ix0 at isa? port 0x300 irq 10 # EtherExpress/16
#iy0 at isa? port 0x360 irq ? # EtherExpress PRO 10 ISA
#lc0 at isa? port 0x320 iomem ? irq ? # DEC EtherWORKS III (LEMAC)
#depca0 at isa? port 0x300 iomem 0xc8000 iosiz 0x8000 irq 5 # DEPCA
#le* at depca?
#nele0 at isa? port 0x320 irq 9 drq 7 # NE2100
#le* at nele?
#ntwoc0 at isa? port 0x300 irq 5 iomem 0xc8000 flags 1 # Riscom/N2 sync serial
#bicc0 at isa? port 0x320 irq 10 drq 7 # BICC IsoLan
#le* at bicc?
#ne0 at isa? port 0x280 irq 9 # NE[12]000 ethernet cards
#ne1 at isa? port 0x300 irq 10
#sm0 at isa? port 0x300 irq 10 # SMC91C9x Ethernet
#tr0 at isa? port 0xa20 iomem 0xd8000 irq ? # IBM TROPIC based Token-Ring
#tr1 at isa? port 0xa24 iomem 0xd0000 irq ? # IBM TROPIC based Token-Ring
#tr* at isa? port ? irq ? # 3COM TROPIC based Token-Ring
#we0 at isa? port 0x280 iomem 0xd0000 irq 9 # WD/SMC Ethernet
#we1 at isa? port 0x300 iomem 0xcc000 irq 10
# CardBus network cards
#ex* at cardbus? dev ? function ? # 3Com 3C575TX
#fxp* at cardbus? dev ? function ? # Intel i8255x
#rtk* at cardbus? dev ? function ? # Realtek 8129/8139
#tlp* at cardbus? dev ? function ? # DECchip 21143
# MII/PHY support
#dmphy* at mii? phy ? # Davicom DM9101 PHYs
#exphy* at mii? phy ? # 3Com internal PHYs
#icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890
#inphy* at mii? phy ? # Intel 82555 PHYs
#iophy* at mii? phy ? # Intel 82553 PHYs
#lxtphy* at mii? phy ? # Level One LXT-970 PHYs
#nsphy* at mii? phy ? # NS83840 PHYs
#nsphyter* at mii? phy ? # NS83843 PHYs
#qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs
#sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
#tlphy* at mii? phy ? # ThunderLAN PHYs
#tqphy* at mii? phy ? # TDK Semiconductor PHYs
#ukphy* at mii? phy ? # generic unknown PHYs
#
# USB Controller and Devices
# PCI USB controllers
#ohci* at pci? dev ? function ? # Open Host Controller
uhci* at pci? dev ? function ? # Universal Host Controller (Intel)
# CardBus USB controllers
#ohci* at cardbus? dev ? function ? # Open Host Controller
# USB bus support
#usb* at ohci?
usb* at uhci?
# USB Hubs
uhub* at usb?
#uhub* at uhub? port ? configuration ? interface ?
# USB Mice
#ums* at uhub? port ? configuration ? interface ?
#wsmouse* at ums? mux 0
# USB Keyboards
#ukbd* at uhub? port ? configuration ? interface ?
#wskbd* at ukbd? console ? mux 1
# USB Generic HID devices
#uhid* at uhub? port ? configuration ? interface ?
# USB Printer
#ulpt* at uhub? port ? configuration ? interface ?
# USB Modem
#umodem* at uhub? port ? configuration ?
#ucom* at umodem?
# USB Mass Storage
#umass* at uhub? port ? configuration ? interface ?
#atapibus* at umass? channel ?
#scsibus* at umass? channel ?
# USB audio
#uaudio* at uhub? port ? configuration ?
# USB Ethernet adapters
#aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters
#cue* at uhub? port ? # CATC USB-EL1201A based adapters
#kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters
# Prolofic PL2301/PL2302 host-to-host adapter
#upl* at uhub? port ?
# Serial adapters
# FTDI FT8U100AX serial adapter
#uftdi* at uhub? port ?
#ucom* at uftdi? portno ?
# Diamond Multimedia Rio 500
#urio* at uhub? port ?
# USB Handspring Visor
#uvisor* at uhub? port ?
#ucom* at uvisor?
# USB Generic driver
#ugen* at uhub? port ?
# Audio Devices
# PCI audio devices
auvia* at pci? dev ? function ? # VIA VT82C686A integrated AC'97 Audio
#clcs* at pci? dev ? function ? # Cirrus Logic CS4280
#cmpci* at pci? dev ? function ? # C-Media CMI8338/8738
#eap* at pci? dev ? function ? # Ensoniq AudioPCI
#eso* at pci? dev ? function ? # ESS Solo-1 PCI AudioDrive
#fms* at pci? dev ? function ? # Forte Media FM801
#sv* at pci? dev ? function ? # S3 SonicVibes
# ISA Plug-and-Play audio devices
#ess* at isapnp? # ESS Tech ES1887, ES1888, ES888 audio
#guspnp* at isapnp? # Gravis Ultra Sound PnP audio
#sb* at isapnp? # SoundBlaster-compatible audio
#wss* at isapnp? # Windows Sound System
#ym* at isapnp? # Yamaha OPL3-SA3 audio
# ISA audio devices
# the "aria" probe might give false hits
#aria0 at isa? port 0x290 irq 10 # Aria
#ess0 at isa? port 0x220 irq 5 drq 1 drq2 5 # ESS 18XX
#gus0 at isa? port 0x220 irq 7 drq 1 drq2 6 # Gravis Ultra Sound
#pas0 at isa? port 0x220 irq 7 drq 1 # ProAudio Spectrum
#pss0 at isa? port 0x220 irq 7 drq 6 # Personal Sound System
#sp0 at pss0 port 0x530 irq 10 drq 0 # sound port driver
#sb0 at isa? port 0x220 irq 5 drq 1 drq2 5 # SoundBlaster
#wss0 at isa? port 0x530 irq 10 drq 0 drq2 1 # Windows Sound System
#cms0 at isa? port 0x220 # Creative Music System
# OPL[23] FM synthesizers
opl0 at isa? port 0x388 # use only if not attached to sound card
#opl* at eso?
#opl* at ess?
#opl* at fms?
#opl* at sb?
#opl* at sv?
#opl* at wss?
#opl* at ym?
# Audio support
#audio* at aria?
audio* at auvia?
#audio* at clcs?
#audio* at cmpci?
#audio* at eap?
#audio* at eso?
#audio* at ess?
#audio* at fms?
#audio* at gus?
#audio* at guspnp?
#audio* at pas?
#audio* at sb?
#audio* at sp?
#audio* at sv?
#audio* at uaudio?
#audio* at wss?
#audio* at ym?
# MPU 401 UARTs
mpu* at isa? port 0x330 irq 9 # MPU401 or compatible card
#mpu* at eso?
#mpu* at fms?
#mpu* at sb?
#mpu* at ym?
# MIDI support
#midi* at clcs? # Cirrus Logic CS4280 MIDI port
#midi* at cms? # Creative Music System
#midi* at eap? # 137[01] MIDI port
midi* at mpu? # MPU 401
midi* at opl? # OPL FM synth
#midi* at pcppi? # MIDI interface to the PC speaker
#midi* at sb? # SB1 MIDI port
# The spkr driver provides a simple tone interface to the built in speaker.
#spkr0 at pcppi? # PC speaker
# TV cards
# Brooktree 848/849/878/879 based TV cards
#bktr* at pci? dev ? function ?
# Mice
# ISA busmice
#lms0 at isa? port 0x23c irq 5 # Logitech bus mouse
#lms1 at isa? port 0x238 irq 5
#mms0 at isa? port 0x23c irq 5 # Microsoft InPort mouse
#mms1 at isa? port 0x238 irq 5
#wsmouse* at lms? mux 0
#wsmouse* at mms? mux 0
# backwards compatible versions
#olms0 at isa? port 0x23c irq 5 # Logitech bus mouse
#olms1 at isa? port 0x238 irq 5
#omms0 at isa? port 0x23c irq 5 # Microsoft InPort mouse
#omms1 at isa? port 0x238 irq 5
#opms0 at pc? irq 12 # PS/2 auxiliary port mouse
# Joysticks
# ISA Plug-and-Play joysticks
#joy* at isapnp? # Game ports (usually on audio cards)
# PCI joysticks
#joy* at pci? # Game ports (usually on audio cards)
# ISA joysticks. Probe is a little strange; add only if you have one.
#joy0 at isa? port 0x201
# Miscellaneous Devices
# Planetconnect Satellite receiver driver.
#satlink0 at isa? port 0x300 drq 1
# Pull in optional local configuration
include "arch/i386/conf/GENERIC.local"
# Pseudo-Devices
# disk/mass storage pseudo-devices
#pseudo-device ccd 4 # concatenated/striped disk devices
#pseudo-device raid 4 # RAIDframe disk driver
#options RAID_AUTOCONFIG # auto-configuration of RAID components
#pseudo-device md 1 # memory disk device (ramdisk)
pseudo-device vnd 4 # disk-like interface to files
# network pseudo-devices
pseudo-device bpfilter 8 # Berkeley packet filter
pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
#pseudo-device ppp 2 # Point-to-Point Protocol
#pseudo-device sl 2 # Serial Line IP
#pseudo-device strip 2 # Starmode Radio IP (Metricom)
pseudo-device tun 2 # network tunneling over tty
#pseudo-device gre 2 # generic L3 over IP tunnel
#pseudo-device ipip 2 # IP Encapsulation within IP (RFC 2003)
pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933)
#pseudo-device faith 1 # IPv[46] tcp relay translation i/f
pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation
# miscellaneous pseudo-devices
pseudo-device pty 64 # pseudo-terminals
#pseudo-device tb 1 # tablet line discipline
pseudo-device sequencer 1 # MIDI sequencer
# rnd works; RND_COM does not on port i386 yet.
pseudo-device rnd # /dev/random and in-kernel generator
#options RND_COM # use "com" randomness as well (BROKEN)
# a pseudo device needed for Coda # also needs CODA (above)
#pseudo-device vcoda 4 # coda minicache <-> venus comm.
# mouse & keyboard multiplexor pseudo-devices
pseudo-device wsmux 2
>From the Audit trail
From: Manuel Bouyer <bouyer@antioche.lip6.fr>
To: nigel@nelgin.nu
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Wed, 9 May 2001 18:04:02 +0200
On Mon, May 07, 2001 at 01:54:40PM -0000, nigel@nelgin.nu wrote:
> >Environment:
> System: NetBSD c643704-b 1.5.1_BETA NetBSD 1.5.1_BETA (WIBBLE) #2: Sun May 6 20:04:40 CDT 2001 nigel@c643704-b:/usr/src/sys/arch/i386/compile/WIBBLE i386
>
>
> >Description:
> I installed an ISA FlexPort 8S into a system (Celeron 533 with 128megs).
> The device is set to irq 5, nothing else uses irq 5. The IO port is left
> at factory settings (jumper is open). dmesg reports the device is found and
> allocates the com devices, however when I "echo hello > /dev/tty03" the
> system locks solid. Telnet sessions are dropped, the console hangs.
> I also tried this on 1.5.1_ALPHA with the same results.
Are you running X when doing this ?
If yes, please repeat in text mode.
If not, please try to enter DDB (ctrl-alt-esc) and get a stack trace ('tr)'.
--
Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
--
From: Nigel Reed <nigel@nelgin.nu>
To: Manuel Bouyer <bouyer@antioche.lip6.fr>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Wed, 9 May 2001 13:36:10 -0500
It happens with or without X running.
The system totally hangs cannot get into DDB. Of course, I made sure
that I could get into DDB before I made the machine lock.
I'm going to build a system with an old 486 cpu/mb combo I have to make
sure it's not the via chipset causing the problems here.
Regards
Nigel
On Wed, May 09, 2001 at 06:04:02PM +0200, Manuel Bouyer wrote:
> On Mon, May 07, 2001 at 01:54:40PM -0000, nigel@nelgin.nu wrote:
> > >Environment:
> > System: NetBSD c643704-b 1.5.1_BETA NetBSD 1.5.1_BETA (WIBBLE) #2: Sun May 6 20:04:40 CDT 2001 nigel@c643704-b:/usr/src/sys/arch/i386/compile/WIBBLE i386
> >
> >
> > >Description:
> > I installed an ISA FlexPort 8S into a system (Celeron 533 with 128megs).
> > The device is set to irq 5, nothing else uses irq 5. The IO port is left
> > at factory settings (jumper is open). dmesg reports the device is found and
> > allocates the com devices, however when I "echo hello > /dev/tty03" the
> > system locks solid. Telnet sessions are dropped, the console hangs.
> > I also tried this on 1.5.1_ALPHA with the same results.
>
> Are you running X when doing this ?
> If yes, please repeat in text mode.
> If not, please try to enter DDB (ctrl-alt-esc) and get a stack trace ('tr)'.
>
> --
> Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
> --
--
From: Nigel Reed <nigel@nelgin.nu>
To: Manuel Bouyer <bouyer@antioche.lip6.fr>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Wed, 9 May 2001 21:02:29 -0500
OK, I tried this on a P166MMX with an Intel motherboard with the same
result, total lockup.
It's either a bad card, or bad NetBSD.
Regards
Nigel
On Wed, May 09, 2001 at 06:04:02PM +0200, Manuel Bouyer wrote:
> On Mon, May 07, 2001 at 01:54:40PM -0000, nigel@nelgin.nu wrote:
> > >Environment:
> > System: NetBSD c643704-b 1.5.1_BETA NetBSD 1.5.1_BETA (WIBBLE) #2: Sun May 6 20:04:40 CDT 2001 nigel@c643704-b:/usr/src/sys/arch/i386/compile/WIBBLE i386
> >
> >
> > >Description:
> > I installed an ISA FlexPort 8S into a system (Celeron 533 with 128megs).
> > The device is set to irq 5, nothing else uses irq 5. The IO port is left
> > at factory settings (jumper is open). dmesg reports the device is found and
> > allocates the com devices, however when I "echo hello > /dev/tty03" the
> > system locks solid. Telnet sessions are dropped, the console hangs.
> > I also tried this on 1.5.1_ALPHA with the same results.
>
> Are you running X when doing this ?
> If yes, please repeat in text mode.
> If not, please try to enter DDB (ctrl-alt-esc) and get a stack trace ('tr)'.
>
> --
> Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
> --
--
From: Manuel Bouyer <bouyer@antioche.lip6.fr>
To: Nigel Reed <nigel@nelgin.nu>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Thu, 10 May 2001 12:04:31 +0200
On Wed, May 09, 2001 at 09:02:29PM -0500, Nigel Reed wrote:
> OK, I tried this on a P166MMX with an Intel motherboard with the same
> result, total lockup.
>
> It's either a bad card, or bad NetBSD.
Hum, I didn't use FlexPort but I had a boca 16 port which should be about the
same: isa board, with 16 16550, shared IRQ. No problems ...
--
Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
--
From: Nigel Reed <nigel@nelgin.nu>
To: Manuel Bouyer <bouyer@antioche.lip6.fr>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Thu, 10 May 2001 07:41:22 -0500
I'm reading the small manual which comes with this device, and this
is saying it has two 16C654 UARTS. addcom_isa.c says that
" * This code was written and tested with the Addonics FlexPort 8S.
* It has 8 ports, using 16650-compatible chips, sharing a single
* interrupt."
I'm assuming that the 16C654 UART is compatibe with the 16650. I'm sure
Michael Graff would be able to tell us exactly what device he used to
test the driver. He hasn't responded to my last email on the subject.
To add a little more to this, I did try to ktrace echo hello > /dev/tty03
but again the system locked up without even writing a ktrace.out file.
Regards
Nigel
From: Manuel Bouyer <bouyer@antioche.lip6.fr>
To: Nigel Reed <nigel@nelgin.nu>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Thu, 10 May 2001 16:16:54 +0200
On Thu, May 10, 2001 at 07:41:22AM -0500, Nigel Reed wrote:
> I'm reading the small manual which comes with this device, and this
> is saying it has two 16C654 UARTS. addcom_isa.c says that
>
> " * This code was written and tested with the Addonics FlexPort 8S.
> * It has 8 ports, using 16650-compatible chips, sharing a single
> * interrupt."
>
> I'm assuming that the 16C654 UART is compatibe with the 16650. I'm sure
> Michael Graff would be able to tell us exactly what device he used to
> test the driver. He hasn't responded to my last email on the subject.
>
> To add a little more to this, I did try to ktrace echo hello > /dev/tty03
> but again the system locked up without even writing a ktrace.out file.
Yes, because it's the shell which will open /dev/tty03 , before starting
the command.
I'm sorry I can't help you much more here.
The complete lock up make me suspect a hardware problem, like I/O port
conflict
--
Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
--
From: Nigel Reed <nigel@nelgin.nu>
To: Manuel Bouyer <bouyer@antioche.lip6.fr>
Cc: gnats-bugs@gnats.netbsd.org
Subject: Re: port-i386/12860: FlexPort 8S hangs NetBSD
Date: Thu, 10 May 2001 09:51:06 -0500
On Thu, May 10, 2001 at 04:16:54PM +0200, Manuel Bouyer wrote:
>
> Yes, because it's the shell which will open /dev/tty03 , before starting
> the command.
> I'm sorry I can't help you much more here.
> The complete lock up make me suspect a hardware problem, like I/O port
> conflict
I've tried using two different IO port ranges. Both of them, as far as I
can tell, were not used by NetBSD for anything else according to dmesg.
Also, I put it into a different machine with different hardware with the
same result. I will try it in a windows machine and see if it locks that
up. If so then I'll assume a bad card. If it does work in the windows
system then I can only assume that the driver or some other part of NetBSD
is at fault. Thanks for looking into it anyway, I'd like to keep the
send-pr open until this is resolved tho.
Regards
Nigel
>How-To-Repeat:
Install FlexPort 8S and repeat.
>Fix:
>Release-Note:
>Audit-Trail:
>Unformatted: