>Number:         35301
>Category:       port-i386
>Synopsis:       ThinkPad X31 ath0 device not working (it worked perfectly before)
>Confidential:   no
>Severity:       serious
>Priority:       medium
>Responsible:    port-i386-maintainer
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Wed Dec 20 22:20:00 +0000 2006
>Originator:     Jun-ichiro itojun Hagino
>Release:        NetBSD 4.99.6
>Organization:
	itojun.org
>Environment:
System: NetBSD starfruit.itojun.org 4.99.6 NetBSD 4.99.6 (STARFRUIT) #0: Wed Dec 20 16:37:21 JST 2006 itojun@starfruit.itojun.org:/home/itojun/NetBSD/src/sys/arch/i386/compile/STARFRUIT i386
Architecture: i386
Machine: i386
>Description:

	ath0 on thinkpad X31 does not work at all.  even if I set SSID (and WEP
	key in some cases) it fials to get hooked up to the network.  (ifconfig
	ath0 will show "no network").  i got multiple 11a/b/g basestations
	but ath0 fails to associate with all of them.

	i haven't upgraded NetBSD on thinkpad X31 since May 2005 (due to my
	sickness).  in May 2005 ath0 worked perfectly.

	there are worrysome message from ath0 at the end of dmesg.  they showed
	up when "ifconfig ath0 up" or change of SSID happened.

--- dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.6 (STARFRUIT) #0: Wed Dec 20 16:37:21 JST 2006
	itojun@starfruit.itojun.org:/home/itojun/NetBSD/src/sys/arch/i386/compile/STARFRUIT
total memory = 1022 MB
avail memory = 995 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd750
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Banias) (686-class), 1398.86 MHz, id 0x695
cpu0: features a7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
cpu0: features a7e9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features a7e9f9bf<FXSR,SSE,SSE2,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1400MHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep (1484 mV) 1400 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1400 1200 1000 800 600
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855PM MCH Host Controller (rev. 0x03)
agp0 at pchb0: aperture at 0xd0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: Intel 82855PM Host-AGP Bridge (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Radeon Mobility M6 LY (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
ehci0: interrupting at irq 11
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 0 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0xaa)
cbb1 at pci2 dev 0 function 1: Ricoh 5C476 PCI-CardBus bridge (rev. 0xaa)
fwohci0 at pci2 dev 0 function 2: Ricoh 5C552 PCI-CardBus bridge/Firewire (rev. 0x02)
fwohci0: interrupting at irq 11
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:06:1b:03:10:00:b0:49
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
wm0 at pci2 dev 1 function 0: Intel i82540EP 1000BASE-T Ethernet, rev. 3
wm0: interrupting at irq 11
wm0: 32-bit 33MHz PCI bus
wm0: 64 word (6 address bits) MicroWire EEPROM
wm0: Ethernet address 00:09:6b:fa:6f:49
makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 4
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ath0 at pci2 dev 2 function 0
ath0: interrupting at irq 11
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 5.9 phy 4.3 radio 3.6
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 6
pcmcia1 at cardslot1
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel 82801DB SMBus Controller (SMBus serial bus, revision 0x01) at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
Intel 82801DB AC97 Modem Controller (modem communications, revision 0x01) at pci0 dev 31 function 6 not configured
isa0 at pcib0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
apm0 at mainbus0: Advanced Power Management BIOS: Power Management spec V1.2
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 38709 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
IPsec: Initialized Security Association Processing.
wd0 at atabus0 drive 0: <IC25N040ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ath0: ath_chan_set: unable to reset channel 7 (2442 MHz, flags 0x3e0 hal flags 0x140)
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ath0: unable to reset hardware; hal status 12
ath0: unable to reset hardware; hal status 0
ath0: unable to reset hardware; hal status 0
ath0: unable to reset hardware; hal status 0
ath0: unable to reset hardware; hal status 0
ath0: unable to reset hardware; hal status 0
>How-To-Repeat:
>Fix: