>Number:         36559
>Category:       install
>Synopsis:       sysinst does not allow selection of SCSI disk to upgrade if IDE disk is available
>Confidential:   no
>Severity:       serious
>Priority:       high
>Responsible:    install-manager
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Tue Jun 26 08:30:00 +0000 2007
>Originator:     Chavdar Ivanov
>Release:        4.99.21
>Organization:
Delcam UK
>Environment:
NetBSD loan8 4.99.20 NetBSD 4.99.20 (GENERIC.MPDRM-8) #1: Fri Jun 15 11:20:28 BST 2007  root@loan8:/f/obj/sys/arch/i386/compile/GENERIC.MPDRM-8 i386
>Description:
HP Kayak XU/800 configured with one SCSI disk sd0 to boot and three IDE data disk. Performing upgrade from 4.99.20, selecting sd0 as the destination disk, results in a message saying that /dev/rwd0a could not be fsck'd - device not configured. This is a second build.sh release, destination and temp directories erased, cvs update from 25/06/2007 ~17:00 GMT. This configuration has been working fine before.

The upgrade was successful on two other systems with only IDE disks attached. 

Dmesg follows:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.20 (GENERIC.MPDRM-8) #1: Fri Jun 15 11:20:28 BST 2007
	root@loan8:/f/obj/sys/arch/i386/compile/GENERIC.MPDRM-8
total memory = 511 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 491 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfdb70
mainbus0 (root)
WARNING: can't reserve area for BIOS PROM.
cpu0 at mainbus0 apid 0: (boot processor)
cpu0: Intel Pentium III (686-class), 797.52 MHz, id 0x683
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 132 MHz
cpu0: 8 page colors
cpu1 at mainbus0 apid 1: (application processor)
cpu1: Intel Pentium III (686-class), 797.48 MHz, id 0x683
cpu1: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 383fbff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu1: features 383fbff<FXSR,SSE>
cpu1: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu1: L2 cache 256 KB 32B/line 8-way
cpu1: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu1: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
ioapic0 at mainbus0 apid 2
ioapic0: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <IBIS  ,HP_KAYAK,19990831>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (PNP0F03): aux port
pckbc1: irq 12
pckbc2 at acpi0 (PNP0303): kbd port
pckbc2: io 0x60,0x64 irq 1
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0700 [PC standard floppy disk controller] at acpi0 not configured
INT0800 [Intel FWH Random Number Generator] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
pcppi1: attached to attimer1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82840 Host (rev. 0x01)
pchb0: random number generator enabled
agp0 at pchb0: aperture at 0xe0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: Intel 82840 AGP (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Radeon 9800SE AH (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
radeondrm0 at vga1
info: [drm] ATI Radeon AH 9800 SE (unit 0)
info: [drm] AGP at 0xe0000000 256MB
info: [drm] Initialized radeon 1.25.0 20060524
ATI Technologies product 0x4168 (miscellaneous display) at pci1 dev 0 function 1 not configured
ppb1 at pci0 dev 2 function 0: Intel 82840 PCI (rev. 0x01)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
ppb2 at pci2 dev 31 function 0: Intel product 0x1360 (rev. 0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
Intel 82806AA PCI64 Hub Advanced Programmable Interrupt Controller (interrupt system, interface 0x20, revision 0x01) at pci3 dev 0 function 0 not configured
ahc1 at pci3 dev 9 function 0: Adaptec aic7892 Ultra160 SCSI adapter
ahc1: interrupting at ioapic0 pin 18 (irq 10)
ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ppb3 at pci0 dev 30 function 0: Intel 82801AA Hub-PCI Bridge (rev. 0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
fxp0 at pci4 dev 8 function 0: Intel i82557 Ethernet, rev 1
fxp0: interrupting at ioapic0 pin 16 (irq 11)
fxp0: May need receiver lock-up workaround
fxp0: Ethernet address 08:00:09:dc:f8:9c
nsphy0 at fxp0 phy 1: DP83840 10/100 media interface, rev. 0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb4 at pci4 dev 11 function 0: HiNT HB1 PCI-PCI Bridge (rev. 0x11)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
fwohci0 at pci5 dev 8 function 0: NEC product 0x00e7 (rev. 0x01)
fwohci0: interrupting at ioapic0 pin 19 (irq 5)
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:01:07:00:0e:bf
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ohci0 at pci5 dev 9 function 0: NEC USB Host Controller (rev. 0x43)
ohci0: interrupting at ioapic0 pin 16 (irq 11)
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1 at pci5 dev 9 function 1: NEC USB Host Controller (rev. 0x43)
ohci1: interrupting at ioapic0 pin 17 (irq 9)
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci5 dev 9 function 2: NEC USB Host Controller (rev. 0x04)
ehci0: interrupting at ioapic0 pin 18 (irq 10)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801AA LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801AA IDE Controller (ICH) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at piixide0 channel 1
Intel 82801AA SMBus Controller (SMBus serial bus, revision 0x02) at pci0 dev 31 function 3 not configured
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <IC35L060AVER07-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus0 drive 1: <WDC WD400BB-23JHA1>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 38162 MB, 77536 cyl, 16 head, 63 sec, 512 bytes/sect x 78156288 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
wd1(piixide0:0:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 1: <Hewlett-Packard DVD Writer 200, CN23S4590J, 1.36> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd2 at atabus1 drive 0: <IC35L060AVER07-0>
wd2: drive supports 16-sector PIO transfers, LBA addressing
wd2: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd2(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
cd0(piixide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
sd0 at scsibus0 target 0 lun 0: <FUJITSU, MAN3184MP, 5507> disk fixed
sd0: 17366 MB, 29694 cyl, 2 head, 598 sec, 512 bytes/sect x 35566478 sectors
sd0: sync (12.50ns offset 127), 16-bit (160.000MB/s) transfers, tagged queueing
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

>How-To-Repeat:
Try to upgrade a system with both SCSI and IDE disks, boooting from the SCSI one. 
>Fix:
N/A, apart from manual upgrade.