>Number:         36838
>Category:       kern
>Synopsis:       pci bus is disabled on ACPI kernel on Fujitsu FMV LOOX P70WN.
>Confidential:   no
>Severity:       serious
>Priority:       high
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sat Aug 25 17:15:00 +0000 2007
>Originator:     ryo@rf7.so-net.ne.jp
>Release:        NetBSD 4.99.30
>Organization:
	
>Environment:
	
	
System: NetBSD chocolate.sweets.tetera.org 4.99.30 NetBSD 4.99.30 (GENERIC) #0: Sat Aug 25 21:50:33 JST 2007 root@chocolate.sweets.tetera.org:/usr/obj/sys/arch/i386/compile/GENERIC i386
Architecture: i386
Machine: i386
>Description:
I cannot enable pci2 on GENERIC kernel.
And on GENERIC.NOACPI kerenl, pci2 is enabled.

I'll show 2 outputs of dmesg (GENERIC and GENERIC.NOACPI).

*** dmesg of GENERIC kernel***

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.30 (GENERIC) #0: Sat Aug 25 21:50:33 JST 2007
	root@chocolate.sweets.tetera.org:/usr/obj/sys/arch/i386/compile/GENERIC
total memory = 1013 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 985 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfdc04
mainbus0 (root)
cpu0 at mainbus0 apid 0: (boot processor)
cpu0: Intel Pentium M (Yonah) (686-class), 1197.10 MHz, id 0x6ec
cpu0: features afe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features afe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9fbff<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR,PDCM>
cpu0: "Intel(R) Core(TM) Solo CPU     U1400  @ 1.20GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: ITLB 128 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 128 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (1052 mV) 1200 MHz
cpu0: unknown Enhanced SpeedStep CPU.
cpu0: Enhanced SpeedStep frequencies available (MHz): 1200 1067 933 800
cpu0: calibrating local timer
cpu0: apic clock running at 133 MHz
cpu0: 64 page colors
ioapic0 at mainbus0 apid 1
ioapic0: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <FUJ   ,PC      ,01130000>, AslId <FUJ ,00000100>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
CPU0 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
CPU1 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
MCFG (PNP0C02) [Plug and Play motherboard register resources] at acpi0 not configured
PCI0 (PNP0A08) [PCI Express/PCI-X Mode-2 Host Bridge] at acpi0 not configured
MBIO (PNP0C02) [Plug and Play motherboard register resources] at acpi0 not configured
com3 at acpi0 (DIGI, FUJ02E6)
com3: io 0x220-0x227 irq 4
com3: ns16550a, working fifo
BTNS (FUJ02BF) at acpi0 not configured
FJEX (FUJ02B1) at acpi0 not configured
CMBT (FUJ02E1) at acpi0 not configured
acpiec0 at acpi0 (EC, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
DMAC (PNP0200) [AT DMA Controller] at acpi0 not configured
attimer1 at acpi0 (TIME, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PIC (PNP0000) [AT Interrupt Controller] at acpi0 not configured
RTC (PNP0B00) [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (MATH, PNP0C04)
npx1: io 0xf0-0xfe irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (KBC, PNP0320): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13): aux port
pckbc2: irq 12
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
hpet0: Found 64-bits HPET, will only use lowest 32-bits
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
LNKA (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKB (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKC (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKD (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKE (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKG (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKH (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
FEXT (FUJ02E3) at acpi0 not configured
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpiacad0 at acpi0 (AC, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (CMB1, PNP0C0A-1): ACPI Battery (Control Method)
acpitz0 at acpi0 (TZ00): ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 100.0C passive 26.8C
acpitz1 at acpi0 (TZ01): ACPI Thermal Zone
acpitz1: unable to get polling interval; using default of 30.0s
acpitz1: critical 100.0C passive 26.8C
apm0 at acpi0: Power Management spec V1.2
acpiacad0: AC adapter online.
acpibat0: battery info: Fujitsu, LION, CP240502 1
pcppi1: attached to attimer1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82945GM/PM/GMS Host Bridge (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xe0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: Intel 82945GM/PM/GMS Integrated Graphics Device (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
direct rendering for vga1 unsupported
Intel 82945GM/PM/GMS Integrated Graphics Device (miscellaneous display, revision 0x03) at pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17 (irq 11)
azalia0: host: Intel 82801GB/GR High Definition Audio Controller (rev. 2)
azalia0: host: High Definition Audio rev. 1.0
ppb0 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 (rev. 0x02)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
mskc0 at pci1 dev 0 function 0mskc0: interrupt moderation is 0 us
, Yukon-2 EC Ultra rev. A1 (0x2): ioapic0 pin 16 (irq 11)
msk0 at mskc0 port A: Ethernet address 00:17:42:3d:72:02
ukphy0 at msk0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3 (rev. 0x02)
pci2 at ppb1 bus 5
pci2: no spaces enabled!
uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci0: interrupting at ioapic0 pin 23 (irq 11)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci1: interrupting at ioapic0 pin 20 (irq 11)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci2: interrupting at ioapic0 pin 18 (irq 11)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci3: interrupting at ioapic0 pin 16 (irq 11)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller (rev. 0x02)
ehci0: interrupting at ioapic0 pin 23 (irq 11)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb2 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe2)
pci3 at ppb2 bus 8
pci3: i/o space, memory space enabled
cbb0 at pci3 dev 3 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0x8d)
Ricoh product 0x0822 (SD Host Controller system, revision 0x13) at pci3 dev 3 function 1 not configured
cbb0: interrupting at ioapic0 pin 16 (irq 11)
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 9
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
ichsmb0 at pci0 dev 31 function 3: Intel 82801GB/GR SMBus Controller (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 19 (irq 11)
iic0 at ichsmb0: I2C bus
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: 0x8384/0x7616 (rev. 2.1)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=2, encodings=1<PCM>
azalia0: playback: PCM formats=e07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1kHz>
azalia0: recording: max channels=2, encodings=1<PCM>
azalia0: recording: PCM formats=e07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1kHz>
azalia0: codec[1]: 0x11c1/0x1040 (rev. 2.0)
azalia0: codec[1]: High Definition Audio rev. 1.0
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
ugen0 at uhub2 port 1
ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.21, addr 2
wd0 at atabus0 drive 0: <TOSHIBA MK6006GAH>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ubt0 at uhub2 port 2
ubt0: vendor 0x0c24 product 0x000f, rev 2.00/19.15, addr 3
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
mskc0: interrupt moderation is 1000 us

*** dmesg of GENERIC.NOACPI ***

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.30 (GENERIC.NOACPI) #0: Sun Aug 26 10:08:28 JST 2007
	root@chocolate.sweets.tetera.org:/usr/obj/sys/arch/i386/compile/GENERIC.NOACPI
total memory = 1013 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 986 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfdc04
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Yonah) (686-class), 1197.08 MHz, id 0x6ec
cpu0: features afe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features afe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9fbff<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR,PDCM>
cpu0: "Intel(R) Core(TM) Solo CPU     U1400  @ 1.20GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: ITLB 128 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 128 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (1052 mV) 1200 MHz
cpu0: unknown Enhanced SpeedStep CPU.
cpu0: Enhanced SpeedStep frequencies available (MHz): 1200 1067 933 800
cpu0: 64 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82945GM/PM/GMS Host Bridge (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xe0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: Intel 82945GM/PM/GMS Integrated Graphics Device (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
direct rendering for vga1 unsupported
Intel 82945GM/PM/GMS Integrated Graphics Device (miscellaneous display, revision 0x03) at pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at irq 11
azalia0: host: Intel 82801GB/GR High Definition Audio Controller (rev. 2)
azalia0: host: High Definition Audio rev. 1.0
ppb0 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 (rev. 0x02)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
mskc0 at pci1 dev 0 function 0mskc0: interrupt moderation is 0 us
, Yukon-2 EC Ultra rev. A1 (0x2): irq 11
msk0 at mskc0 port A: Ethernet address 00:17:42:3d:72:02
ukphy0 at msk0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3 (rev. 0x02)
pci2 at ppb1 bus 5
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci2 dev 0 function 0: Intel PRO/Wireless LAN 3945ABG Mini-PCI Adapter (rev. 0x02)
wpi0: interrupting at irq 11
, JPN, address 00:1b:77:0c:6f:4a
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci3: interrupting at irq 11
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller (rev. 0x02)
ehci0: interrupting at irq 11
ehci0: BIOS refuses to give up ownership, using force
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb2 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe2)
pci3 at ppb2 bus 8
pci3: i/o space, memory space enabled
cbb0 at pci3 dev 3 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0x8d)
Ricoh product 0x0822 (SD Host Controller system, revision 0x13) at pci3 dev 3 function 1 not configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 9
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
ichsmb0 at pci0 dev 31 function 3: Intel 82801GB/GR SMBus Controller (rev. 0x02)
ichsmb0: interrupting at irq 11
iic0 at ichsmb0: I2C bus
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: 0x8384/0x7616 (rev. 2.1)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=2, encodings=1<PCM>
azalia0: playback: PCM formats=e07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1kHz>
azalia0: recording: max channels=2, encodings=1<PCM>
azalia0: recording: PCM formats=e07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1kHz>
azalia0: codec[1]: 0x11c1/0x1040 (rev. 2.0)
azalia0: codec[1]: High Definition Audio rev. 1.0
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
ugen0 at uhub2 port 1
ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.21, addr 2
wd0 at atabus0 drive 0: <TOSHIBA MK6006GAH>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ubt0 at uhub2 port 2
ubt0: vendor 0x0c24 product 0x000f, rev 2.00/19.15, addr 3
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

>How-To-Repeat:
boot with GENERIC kernel on Fujitsu FMV-BIBLO LOOX P70WN (FMVLP70WN).
>Fix:
I have no idea.

>Unformatted: