>Number:         37001
>Category:       port-i386
>Synopsis:       acpi enabled kernel locks up bringing up fxp0 NIC
>Confidential:   no
>Severity:       serious
>Priority:       low
>Responsible:    port-i386-maintainer
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Mon Sep 17 21:10:00 +0000 2007
>Originator:     Mathias De Belder
>Release:        NetBSD 4.0_RC1
>Organization:
>Environment:
System: NetBSD merean.lan 4.0_RC1 NetBSD 4.0_RC1 (GENERIC.NOACPI) #0: Sat Sep 1 15:59:45 PDT 2007 builds@wb42:/home/builds/ab/netbsd-4-0-RC1/i386/200709011431Z-obj/home/builds/ab/netbsd-4-0-RC1/src/sys/arch/i386/compile/GENERIC.NOACPI i386
Architecture: i386
Machine: i386
>Description:

NetBSD 4.0_RC1's kernel locks up completely when bringing up
fxp0 when acpi is enabled.  On a kernel with acpi disabled, bringing up
the network works, and the NIC works fine (at least it can transfer a
couple of gigabytes over NFS near wire speed).

Dell Latitude D505, i855m chipset, Intel PRO/100 VE (MOB) NIC, dothan CPU.
It's a bog standard, 3 year old centrino laptop which has never exhibted
problems under any linux kernel or on freebsd (only 6 series tested). I
have never seen acpi related problems, nor did I ever had a problem getting
the NIC to work in other operating systems.

>How-To-Repeat:

Use any kernel with acpi enabled (GENERIC, GENERIC_LAPTOP). Boot and then
try 'ifconfig fxp0 192.168.1.100 up'. The kernel hangs hard, no response
to keyboard input.

However, the INSTALL and GENERIC.NOACPI kernels work fine.
(Ironically, the system was installed over a pxe netboot 
 and network install.)

>Fix:

Use NOACPI kernel.  Default install with a GENERIC kernel will not work.

Two dmesg's are attached, one with and one without acpi (I know that the
acpi version is a custom kernel, but the results are the same with the 
standard kernels).  

Note how the IRQ assignment to fxp0 differs.


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_RC1 (MEREAN) #0: Mon Sep 17 20:22:30 CEST 2007
	root@:/usr/src/sys/arch/i386/compile/MEREAN
total memory = 1022 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 998 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xffe90
PCI BIOS rev. 2.1 found at 0xfc96e
pcibios: config mechanism [1][x], special cycles [x][x], last bus 1
PCI IRQ Routing Table rev. 1.0 found at 0xfc590, size 176 bytes (9 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371MX (MPIIX) Mobile PCI I/O IDE Xcelerator compatible)
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:02:0 0x8086 0x3582   A  0x00  11  0    already assigned
000:29:0 0x8086 0x24c2   A  0x00  11  0    already assigned
000:29:1 0x8086 0x24c4   B  0x03  11  0    already assigned
000:29:2 0x8086 0x24c7   C  0x02  11  0    already assigned
000:29:7 0x8086 0x24cd   D  0x07  11  0    already assigned
000:31:1 0x8086 0x24ca   A  0x02  11  0    fixed up
000:31:5 0x8086 0x24c5   B  0x01  11  0    already assigned
001:01:0 0x104c 0xac44   A  0x00  11  0    already assigned
001:01:1 0x104c 0x8029   B  0x03  11  0    already assigned
001:08:0 0x8086 0x103d   A  0x04  11  0    already assigned
------------------------------------------
mainbus0 (root)
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x3ff00000
pci_addr_fixup: 001:01:0 0x104c 0xac44 new address 0x3ff01000
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Dothan) (686-class), 599.52 MHz, id 0x6d6
cpu0: features afe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
cpu0: features afe9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9f9bf<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1.70GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep (988 mV) 600 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1700 1400 1200 1000 800 600
cpu0: 64 page colors
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <DELL  , CPi R  ,27d40903>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
mpacpi: could not get bus number, assuming bus 0
LNKA: ACPI: Found matching pin for 0.31.INTA at func 1: 11
LNKB: ACPI: Found matching pin for 0.31.INTB at func 5: 11
LNKB: BIOS IRQ 11 for 0.31.INTB is invalid
LNKA: ACPI: Found matching pin for 0.29.INTA at func 0: 11
LNKD: ACPI: Found matching pin for 0.29.INTB at func 1: 11
LNKC: ACPI: Found matching pin for 0.29.INTC at func 2: 11
LNKH: ACPI: Found matching pin for 0.29.INTD at func 7: 11
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKA: ACPI: Found matching pin for 1.1.INTA at func 0: 255
LNKD: ACPI: Found matching pin for 1.1.INTB at func 1: 11
LNKE: ACPI: Found matching pin for 1.8.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 1.8.INTA at func 0: 11
LNKB: BIOS IRQ 11 for 1.8.INTA is invalid
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
acpibut1 at acpi0 (PNP0C0E): ACPI Sleep Button
PNP0C01 at acpi0 not configured
PNP0A03 at acpi0 not configured
PNP0C01 at acpi0 not configured
PNP0C01 at acpi0 not configured
PNP0F13 at acpi0 not configured
PNP0303 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0800 at acpi0 not configured
PNP0C01 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C01 at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 101.0C
apm0 at acpi0: Power Management spec V1.2
acpiacad0: AC adapter online.
acpibat0: battery info: Sony, LION, DELL C26034, 12846
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-Hub Controller (rev. 0x02)
agp0 at pchb0: detected 892k stolen memory
agp0: aperture at 0xf0000000, size 0x8000000
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
ehci0: interrupting at irq 11
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
cbb0 at pci1 dev 1 function 0: Texas Instruments PCI4510 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x02)
Texas Instruments PCI4510 IEEE 1394 Host Controller w/ PCI-CardBus Bridge (Firewire serial bus, interface 0x10) at pci1 dev 1 function 1 not configured
fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE (MOB) Network Controller, rev 129
LNKB: Picked IRQ 9 with weight 0
fxp0: interrupting at irq 9
fxp0: Ethernet address 00:0f:1f:c3:3d:0b
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 9
auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC, SigmaTel 3D
auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
WARNING: Callback scheduled before sysmon task queue thread present.
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 48002 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse1 at ums0 mux 0
uhidev1 at uhub1 port 1 configuration 1 interface 0
uhidev1: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/1
ukbd0 at uhidev1
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev2 at uhub1 port 1 configuration 1 interface 1
uhidev2: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/0
uhidev2: 3 report ids
uhid0 at uhidev2 reportid 1: input=7, output=0, feature=0
uhid1 at uhidev2 reportid 3: input=1, output=0, feature=0
wd0 at atabus0 drive 0: <WDC WD800VE-00HDT0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <QSI CD-RW/DVD-ROM SBW242U, , UD25> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


noacpi:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_RC1 (GENERIC.NOACPI) #0: Sat Sep  1 15:59:45 PDT 2007
	builds@wb42:/home/builds/ab/netbsd-4-0-RC1/i386/200709011431Z-obj/home/builds/ab/netbsd-4-0-RC1/src/sys/arch/i386/compile/GENERIC.NOACPI
total memory = 1022 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 994 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xffe90
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Dothan) (686-class), 599.52 MHz, id 0x6d6
cpu0: features afe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
cpu0: features afe9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9f9bf<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1.70GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep (988 mV) 600 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1700 1400 1200 1000 800 600
cpu0: 64 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-Hub Controller (rev. 0x02)
agp0 at pchb0: detected 892k stolen memory
agp0: aperture at 0xf0000000, size 0x8000000
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
ehci0: interrupting at irq 11
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
cbb0 at pci1 dev 1 function 0: Texas Instruments PCI4510 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x02)
fwohci0 at pci1 dev 1 function 1: Texas Instruments PCI4510 IEEE 1394 Host Controller w/ PCI-CardBus Bridge (rev. 0x00)
fwohci0: interrupting at irq 11
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 47:4f:c0:00:2a:c1:24:30
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE (MOB) Network Controller, rev 129
fxp0: interrupting at irq 11
fxp0: Ethernet address 00:0f:1f:c3:3d:0b
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: interrupting at irq 11
cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
cardslot0 at cbb0 slot 0 flags 0
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC, SigmaTel 3D
auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 40682 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse1 at ums0 mux 0
uhidev1 at uhub1 port 1 configuration 1 interface 0
uhidev1: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/1
ukbd0 at uhidev1
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev2 at uhub1 port 1 configuration 1 interface 1
uhidev2: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/0
uhidev2: 3 report ids
uhid0 at uhidev2 reportid 1: input=7, output=0, feature=0
uhid1 at uhidev2 reportid 3: input=1, output=0, feature=0
wd0 at atabus0 drive 0: <WDC WD800VE-00HDT0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <QSI CD-RW/DVD-ROM SBW242U, , UD25> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


Working ifconfig output:

$ ifconfig -a
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        address: 47:4f:c0:00:2a:c1:24:30
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	address: 00:0f:1f:c3:3d:0b
	media: Ethernet autoselect (100baseTX full-duplex,flowcontrol,rxpause,txpause)
	status: active
	inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
	inet6 fe80::20f:1fff:fec3:3d0b%fxp0 prefixlen 64 scopeid 0x2
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33192
	inet 127.0.0.1 netmask 0xff000000
	inet6 ::1 prefixlen 128
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3


fwip0 is *not* present on the acpi enabled kernel with ifconfig -a.