The following reply was made to PR port-i386/37001; it has been noted by GNATS.

From: Mathias De Belder <mathias@woei.be>
To: gnats-bugs@NetBSD.org
Cc: 
Subject: Re: port-i386/37001 (acpi enabled kernel locks up bringing up fxp0
	NIC)
Date: Thu, 1 Nov 2007 00:36:55 +0100

 >  On Wed, Oct 31, 2007 at 09:50:02PM +0000, Mathias De Belder wrote:
 >  >  Unfortunately, the problem still persists.  The machine locks up right
 >  >  after bringing up fxp0.  If you have any more ideas or patches to try
 >  >  out, I'll be happy to test them out.
 >  
 >  Does the dmesg still show the same interrupt routing as before?
 
 It does.
 
 I've attached the new dmesg output below of a kernel with your
 previously posted patch applied:
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
     2006, 2007
     The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.
 
 NetBSD 4.0_RC3 (GENERIC) #0: Wed Oct 31 19:16:26 CET 2007
 	mathias@merean.lan:/usr/obj/sys/arch/i386/compile/GENERIC
 total memory = 1022 MB
 rbus: rbus_min_start set to 0x40000000
 avail memory = 994 MB
 timecounter: Timecounters tick every 10.000 msec
 timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
 BIOS32 rev. 0 found at 0xffe90
 mainbus0 (root)
 cpu0 at mainbus0: (uniprocessor)
 cpu0: Intel Pentium M (Dothan) (686-class), 599.51 MHz, id 0x6d6
 cpu0: features afe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
 cpu0: features afe9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
 cpu0: features afe9f9bf<FXSR,SSE,SSE2,SS,TM,SBF>
 cpu0: features2 180<EST,TM2>
 cpu0: "Intel(R) Pentium(R) M processor 1.70GHz"
 cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
 cpu0: L2 cache 2 MB 64B/line 8-way
 cpu0: using thermal monitor 2
 cpu0: Enhanced SpeedStep (988 mV) 600 MHz
 cpu0: Enhanced SpeedStep frequencies available (MHz): 1700 1400 1200 1000 800 600
 cpu0: 64 page colors
 acpi0 at mainbus0: Advanced Configuration and Power Interface
 acpi0: using Intel ACPI CA subsystem version 20060217
 acpi0: X/RSDT: OemId <DELL  , CPi R  ,27d40903>, AslId <ASL ,00000061>
 acpi0: SCI interrupting at int 9
 timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
 ACPI-Fast 24-bit timer
 mpacpi: could not get bus number, assuming bus 0
 LNKA: ACPI: Found matching pin for 0.31.INTA at func 1: 0
 LNKB: ACPI: Found matching pin for 0.31.INTB at func 5: 11
 LNKB: BIOS IRQ 11 for 0.31.INTB is invalid
 LNKA: ACPI: Found matching pin for 0.29.INTA at func 0: 11
 LNKD: ACPI: Found matching pin for 0.29.INTB at func 1: 11
 LNKC: ACPI: Found matching pin for 0.29.INTC at func 2: 11
 LNKH: ACPI: Found matching pin for 0.29.INTD at func 7: 11
 LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
 LNKA: ACPI: Found matching pin for 1.1.INTA at func 0: 255
 LNKD: ACPI: Found matching pin for 1.1.INTB at func 1: 11
 LNKE: ACPI: Found matching pin for 1.8.INTA at func 0: 11
 LNKB: ACPI: Found matching pin for 1.8.INTA at func 0: 11
 LNKB: BIOS IRQ 11 for 1.8.INTA is invalid
 ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
 acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
 acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
 acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
 acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
 acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
 acpibut1 at acpi0 (PNP0C0E): ACPI Sleep Button
 PNP0C01 [System Board] at acpi0 not configured
 PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
 PNP0C01 [System Board] at acpi0 not configured
 PNP0C01 [System Board] at acpi0 not configured
 pckbc1 at acpi0 (PNP0F13): aux port
 pckbc1: irq 12
 pckbc2 at acpi0 (PNP0303): kbd port
 pckbc2: io 0x60,0x64 irq 1
 PNP0B00 [AT Real-Time Clock] at acpi0 not configured
 attimer1 at acpi0 (PNP0100): AT Timer
 attimer1: io 0x40-0x43,0x50-0x53 irq 0
 pcppi1 at acpi0 (PNP0800)
 pcppi1: io 0x61,0x63,0x65,0x67
 pcppi1: children must have an explicit unit
 midi0 at pcppi1: PC speaker (CPU-intensive output)
 sysbeep0 at pcppi1
 PNP0C01 [System Board] at acpi0 not configured
 PNP0000 [AT Interrupt Controller] at acpi0 not configured
 PNP0200 [AT DMA Controller] at acpi0 not configured
 npx1 at acpi0 (PNP0C04)
 npx1: io 0xf0-0xff irq 13
 npx1: reported by CPUID; using exception 16
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C0F [PCI interrupt link device] at acpi0 not configured
 PNP0C01 [System Board] at acpi0 not configured
 acpitz0 at acpi0: ACPI Thermal Zone
 acpitz0: unable to get polling interval; using default of 30.0s
 acpitz0: passive cooling mode only
 acpitz0: critical 101.0C
 pckbd0 at pckbc2 (kbd slot)
 pckbc2: using irq 1 for kbd slot
 wskbd0 at pckbd0: console keyboard
 pms0 at pckbc2 (aux slot)
 pckbc2: using irq 12 for aux slot
 wsmouse0 at pms0 mux 0
 pcppi1: attached to attimer1
 pci0 at mainbus0 bus 0: configuration mode 1
 pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 pchb0 at pci0 dev 0 function 0
 pchb0: Intel 82855GM Host-Hub Controller (rev. 0x02)
 agp0 at pchb0: detected 892k stolen memory
 agp0: aperture at 0xf0000000, size 0x8000000
 Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
 Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
 vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
 wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
 wsmux1: connecting to wsdisplay0
 Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
 uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci0: interrupting at irq 11
 usb0 at uhci0: USB revision 1.0
 uhub0 at usb0
 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered
 uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci1: interrupting at irq 11
 usb1 at uhci1: USB revision 1.0
 uhub1 at usb1
 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 2 ports with 2 removable, self powered
 uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci2: interrupting at irq 11
 usb2 at uhci2: USB revision 1.0
 uhub2 at usb2
 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub2: 2 ports with 2 removable, self powered
 ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
 ehci0: interrupting at irq 11
 ehci0: BIOS has given up ownership
 ehci0: EHCI version 1.0
 ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
 usb3 at ehci0: USB revision 2.0
 uhub3 at usb3
 uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 uhub3: 6 ports with 6 removable, self powered
 ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
 pci1 at ppb0 bus 1
 pci1: i/o space, memory space enabled
 cbb0 at pci1 dev 1 function 0: Texas Instruments PCI4510 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x02)
 fwohci0 at pci1 dev 1 function 1: Texas Instruments PCI4510 IEEE 1394 Host Controller w/ PCI-CardBus Bridge (rev. 0x00)
 fwohci0: interrupting at irq 11
 fwohci0: OHCI version 1.10 (ROM=0)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 47:4f:c0:00:2a:c1:24:30
 fwohci0: Phy 1394a available S400, 2 ports.
 fwohci0: Link S400, max_rec 2048 bytes.
 ieee1394if0 at fwohci0: IEEE1394 bus
 fwip0 at ieee1394if0: IP over IEEE1394
 fwohci0: Initiate bus reset
 fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE (MOB) Network Controller, rev 129
 LNKB: Picked IRQ 9 with weight 0
 fxp0: interrupting at irq 9
 fxp0: Ethernet address 00:0f:1f:c3:3d:0b
 inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 cbb0: interrupting at irq 11
 cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
 cardslot0 at cbb0 slot 0 flags 0
 pcmcia0 at cardslot0
 pcib0 at pci0 dev 31 function 0
 pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
 piixide0 at pci0 dev 31 function 1
 piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
 piixide0: bus-master DMA support present
 piixide0: primary channel configured to compatibility mode
 piixide0: primary channel interrupting at irq 14
 atabus0 at piixide0 channel 0
 piixide0: secondary channel configured to compatibility mode
 piixide0: secondary channel interrupting at irq 15
 atabus1 at piixide0 channel 1
 auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
 auich0: interrupting at irq 9
 auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC, SigmaTel 3D
 auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
 isa0 at pcib0
 isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
 isapnp0: no ISA Plug 'n Play devices found
 WARNING: Callback scheduled before sysmon task queue thread present.
 fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
 ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
 ieee1394if0: bus manager 0 (me)
 timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
 auich0: measured ac97 link rate at 48002 Hz, will use 48000 Hz
 audio0 at auich0: full duplex, mmap, independent
 Kernelized RAIDframe activated
 uhidev0 at uhub0 port 1 configuration 1 interface 0
 uhidev0: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/1
 ukbd0 at uhidev0
 wskbd1 at ukbd0 mux 1
 wskbd1: connecting to wsdisplay0
 uhidev1 at uhub0 port 1 configuration 1 interface 1
 uhidev1: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/0
 uhidev1: 3 report ids
 uhid0 at uhidev1 reportid 1: input=7, output=0, feature=0
 uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
 uhidev2 at uhub1 port 1 configuration 1 interface 0
 uhidev2: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
 ums0 at uhidev2: 8 buttons and Z dir.
 wsmouse1 at ums0 mux 0
 wd0 at atabus0 drive 0: <WDC WD800VE-00HDT0>
 wd0: drive supports 16-sector PIO transfers, LBA addressing
 wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
 wd0: 32-bit data port
 wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
 wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
 atapibus0 at atabus1: 2 targets
 cd0 at atapibus0 drive 0: <QSI CD-RW/DVD-ROM SBW242U, , UD25> cdrom removable
 cd0: 32-bit data port
 cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
 cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
 boot device: wd0
 root on wd0a dumps on wd0b
 root file system type: ffs
 wsdisplay0: screen 1 added (80x25, vt100 emulation)
 wsdisplay0: screen 2 added (80x25, vt100 emulation)
 wsdisplay0: screen 3 added (80x25, vt100 emulation)
 wsdisplay0: screen 4 added (80x25, vt100 emulation)
 
 
 
 As a reference, here is the dmesg output again of the original kernel
 without your attached patch:
 
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
     The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.
 
 NetBSD 4.0_RC1 (MEREAN) #0: Mon Sep 17 20:22:30 CEST 2007
 	root@:/usr/src/sys/arch/i386/compile/MEREAN
 total memory = 1022 MB
 rbus: rbus_min_start set to 0x40000000
 avail memory = 998 MB
 timecounter: Timecounters tick every 10.000 msec
 timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
 BIOS32 rev. 0 found at 0xffe90
 PCI BIOS rev. 2.1 found at 0xfc96e
 pcibios: config mechanism [1][x], special cycles [x][x], last bus 1
 PCI IRQ Routing Table rev. 1.0 found at 0xfc590, size 176 bytes (9 entries)
 PCI Interrupt Router at 000:31:0 (Intel 82371MX (MPIIX) Mobile PCI I/O IDE Xcelerator compatible)
 ------------------------------------------
   device vendor product pin PIRQ IRQ stage
 ------------------------------------------
 000:02:0 0x8086 0x3582   A  0x00  11  0    already assigned
 000:29:0 0x8086 0x24c2   A  0x00  11  0    already assigned
 000:29:1 0x8086 0x24c4   B  0x03  11  0    already assigned
 000:29:2 0x8086 0x24c7   C  0x02  11  0    already assigned
 000:29:7 0x8086 0x24cd   D  0x07  11  0    already assigned
 000:31:1 0x8086 0x24ca   A  0x02  11  0    fixed up
 000:31:5 0x8086 0x24c5   B  0x01  11  0    already assigned
 001:01:0 0x104c 0xac44   A  0x00  11  0    already assigned
 001:01:1 0x104c 0x8029   B  0x03  11  0    already assigned
 001:08:0 0x8086 0x103d   A  0x04  11  0    already assigned
 ------------------------------------------
 mainbus0 (root)
 pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x3ff00000
 pci_addr_fixup: 001:01:0 0x104c 0xac44 new address 0x3ff01000
 cpu0 at mainbus0: (uniprocessor)
 cpu0: Intel Pentium M (Dothan) (686-class), 599.52 MHz, id 0x6d6
 cpu0: features afe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
 cpu0: features afe9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
 cpu0: features afe9f9bf<FXSR,SSE,SSE2,SS,TM,SBF>
 cpu0: features2 180<EST,TM2>
 cpu0: "Intel(R) Pentium(R) M processor 1.70GHz"
 cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
 cpu0: L2 cache 2 MB 64B/line 8-way
 cpu0: using thermal monitor 2
 cpu0: Enhanced SpeedStep (988 mV) 600 MHz
 cpu0: Enhanced SpeedStep frequencies available (MHz): 1700 1400 1200 1000 800 600
 cpu0: 64 page colors
 acpi0 at mainbus0: Advanced Configuration and Power Interface
 acpi0: using Intel ACPI CA subsystem version 20060217
 acpi0: X/RSDT: OemId <DELL  , CPi R  ,27d40903>, AslId <ASL ,00000061>
 acpi0: SCI interrupting at int 9
 timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
 ACPI-Fast 24-bit timer
 mpacpi: could not get bus number, assuming bus 0
 LNKA: ACPI: Found matching pin for 0.31.INTA at func 1: 11
 LNKB: ACPI: Found matching pin for 0.31.INTB at func 5: 11
 LNKB: BIOS IRQ 11 for 0.31.INTB is invalid
 LNKA: ACPI: Found matching pin for 0.29.INTA at func 0: 11
 LNKD: ACPI: Found matching pin for 0.29.INTB at func 1: 11
 LNKC: ACPI: Found matching pin for 0.29.INTC at func 2: 11
 LNKH: ACPI: Found matching pin for 0.29.INTD at func 7: 11
 LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
 LNKA: ACPI: Found matching pin for 1.1.INTA at func 0: 255
 LNKD: ACPI: Found matching pin for 1.1.INTB at func 1: 11
 LNKE: ACPI: Found matching pin for 1.8.INTA at func 0: 11
 LNKB: ACPI: Found matching pin for 1.8.INTA at func 0: 11
 LNKB: BIOS IRQ 11 for 1.8.INTA is invalid
 ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
 acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
 acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
 acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
 acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
 acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
 acpibut1 at acpi0 (PNP0C0E): ACPI Sleep Button
 PNP0C01 at acpi0 not configured
 PNP0A03 at acpi0 not configured
 PNP0C01 at acpi0 not configured
 PNP0C01 at acpi0 not configured
 PNP0F13 at acpi0 not configured
 PNP0303 at acpi0 not configured
 PNP0B00 at acpi0 not configured
 PNP0100 at acpi0 not configured
 PNP0800 at acpi0 not configured
 PNP0C01 at acpi0 not configured
 PNP0000 at acpi0 not configured
 PNP0200 at acpi0 not configured
 PNP0C04 at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C0F at acpi0 not configured
 PNP0C01 at acpi0 not configured
 acpitz0 at acpi0: ACPI Thermal Zone
 acpitz0: unable to get polling interval; using default of 30.0s
 acpitz0: passive cooling mode only
 acpitz0: critical 101.0C
 apm0 at acpi0: Power Management spec V1.2
 acpiacad0: AC adapter online.
 acpibat0: battery info: Sony, LION, DELL C26034, 12846
 pci0 at mainbus0 bus 0: configuration mode 1
 pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 pchb0 at pci0 dev 0 function 0
 pchb0: Intel 82855GM Host-Hub Controller (rev. 0x02)
 agp0 at pchb0: detected 892k stolen memory
 agp0: aperture at 0xf0000000, size 0x8000000
 Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
 Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
 vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
 wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
 wsmux1: connecting to wsdisplay0
 Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
 uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci0: interrupting at irq 11
 usb0 at uhci0: USB revision 1.0
 uhub0 at usb0
 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered
 uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci1: interrupting at irq 11
 usb1 at uhci1: USB revision 1.0
 uhub1 at usb1
 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 2 ports with 2 removable, self powered
 uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
 uhci2: interrupting at irq 11
 usb2 at uhci2: USB revision 1.0
 uhub2 at usb2
 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub2: 2 ports with 2 removable, self powered
 ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
 ehci0: interrupting at irq 11
 ehci0: BIOS has given up ownership
 ehci0: EHCI version 1.0
 ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
 usb3 at ehci0: USB revision 2.0
 uhub3 at usb3
 uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 uhub3: 6 ports with 6 removable, self powered
 ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
 pci1 at ppb0 bus 1
 pci1: i/o space, memory space enabled
 cbb0 at pci1 dev 1 function 0: Texas Instruments PCI4510 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x02)
 Texas Instruments PCI4510 IEEE 1394 Host Controller w/ PCI-CardBus Bridge (Firewire serial bus, interface 0x10) at pci1 dev 1 function 1 not configured
 fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE (MOB) Network Controller, rev 129
 LNKB: Picked IRQ 9 with weight 0
 fxp0: interrupting at irq 9
 fxp0: Ethernet address 00:0f:1f:c3:3d:0b
 inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 cbb0: interrupting at irq 11
 cardslot0 at cbb0 slot 0 flags 0
 cardbus0 at cardslot0: bus 2
 pcmcia0 at cardslot0
 pcib0 at pci0 dev 31 function 0
 pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
 piixide0 at pci0 dev 31 function 1
 piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
 piixide0: bus-master DMA support present
 piixide0: primary channel configured to compatibility mode
 piixide0: primary channel interrupting at irq 14
 atabus0 at piixide0 channel 0
 piixide0: secondary channel configured to compatibility mode
 piixide0: secondary channel interrupting at irq 15
 atabus1 at piixide0 channel 1
 auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
 auich0: interrupting at irq 9
 auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC, SigmaTel 3D
 auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
 isa0 at pcib0
 pckbc0 at isa0 port 0x60-0x64
 pckbd0 at pckbc0 (kbd slot)
 pckbc0: using irq 1 for kbd slot
 wskbd0 at pckbd0: console keyboard, using wsdisplay0
 pms0 at pckbc0 (aux slot)
 pckbc0: using irq 12 for aux slot
 wsmouse0 at pms0 mux 0
 attimer0 at isa0 port 0x40-0x43: AT Timer
 pcppi0 at isa0 port 0x61
 pcppi0: children must have an explicit unit
 midi0 at pcppi0: PC speaker (CPU-intensive output)
 sysbeep0 at pcppi0
 isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
 npx0 at isa0 port 0xf0-0xff
 npx0: reported by CPUID; using exception 16
 pcppi0: attached to attimer0
 isapnp0: no ISA Plug 'n Play devices found
 WARNING: Callback scheduled before sysmon task queue thread present.
 timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
 auich0: measured ac97 link rate at 48002 Hz, will use 48000 Hz
 audio0 at auich0: full duplex, mmap, independent
 Kernelized RAIDframe activated
 uhidev0 at uhub0 port 1 configuration 1 interface 0
 uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
 ums0 at uhidev0: 8 buttons and Z dir.
 wsmouse1 at ums0 mux 0
 uhidev1 at uhub1 port 1 configuration 1 interface 0
 uhidev1: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/1
 ukbd0 at uhidev1
 wskbd1 at ukbd0 mux 1
 wskbd1: connecting to wsdisplay0
 uhidev2 at uhub1 port 1 configuration 1 interface 1
 uhidev2: Microsoft MicrosoftM-BM-. Digital Media Pro Keyboard, rev 2.00/1.10, addr 2, iclass 3/0
 uhidev2: 3 report ids
 uhid0 at uhidev2 reportid 1: input=7, output=0, feature=0
 uhid1 at uhidev2 reportid 3: input=1, output=0, feature=0
 wd0 at atabus0 drive 0: <WDC WD800VE-00HDT0>
 wd0: drive supports 16-sector PIO transfers, LBA addressing
 wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
 wd0: 32-bit data port
 wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
 wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
 atapibus0 at atabus1: 2 targets
 cd0 at atapibus0 drive 0: <QSI CD-RW/DVD-ROM SBW242U, , UD25> cdrom removable
 cd0: 32-bit data port
 cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
 cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
 boot device: wd0
 root on wd0a dumps on wd0b
 root file system type: ffs
 wsdisplay0: screen 1 added (80x25, vt100 emulation)
 wsdisplay0: screen 2 added (80x25, vt100 emulation)
 wsdisplay0: screen 3 added (80x25, vt100 emulation)
 wsdisplay0: screen 4 added (80x25, vt100 emulation)
 
 
 Mathias