Re: port-i386/26074 - Boot failure on shuttle ST61G4, plus ACPI problems

[David Brownlee <abs%NetBSD.org@localhost>]

The following reply was made to PR port-i386/26074; it has been noted by GNATS.

From: David Brownlee <abs%NetBSD.org@localhost>
To: gnats-bugs%NetBSD.org@localhost
Cc: 
Subject: Re: port-i386/26074 - Boot failure on shuttle ST61G4, plus ACPI
 problems
Date: Sat, 5 Jan 2008 10:52:16 +0000 (GMT)

        Matters are improved with NetBSD 4.0. An ACPI kernel boots, but
        the PC keyboard is non responsive. A USB keyboard works, but
        obviously only after autoconfig has completed.
 
        updated dmesg:
 
        Note: the onboard bce0 fails when the machine has 2G of memory, which
        is another issue :)
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
      2006, 2007
      The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
      The Regents of the University of California.  All rights reserved.
 
 NetBSD 4.0_STABLE (_ACPI_) #1: Mon Dec 17 14:59:17 GMT 2007
        
root%iris.absd.org@localhost:/var/obj/i386/home/netbsd/4/sys/arch/i386/compile/_ACPI_
 total memory = 2037 MB
 rbus: rbus_min_start set to 0x80000000
 avail memory = 1992 MB
 timecounter: Timecounters tick every 0.976 msec
 timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
 BIOS32 rev. 0 found at 0xfb420
 SMBIOS rev. 2.2 @ 0xf0000 (47 entries)
 mainbus0 (root)
 pci_addr_fixup: 000:20:1 0x1002 0x4349 new address 0x00005800
 pci_addr_fixup: 000:20:1 0x1002 0x4349 new address 0x00005808
 pci_addr_fixup: 000:20:1 0x1002 0x4349 new address 0x00005810
 pci_addr_fixup: 000:20:1 0x1002 0x4349 new address 0x0000580c
 cpu0 at mainbus0: apid 0 (boot processor)
 cpu0: Intel Celeron (686-class), 2394.48 MHz, id 0xf29
 cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
 cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
 cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
 cpu0: features2 4400<CID,xTPR>
 cpu0: "Intel(R) Celeron(R) CPU 2.40GHz"
 cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64B/line 4-way
 cpu0: ITLB 4K/4M: 128 entries
 cpu0: DTLB 4K/4M: 64 entries
 cpu0: enabling thermal monitor 1 ... enabled.
 cpu0: calibrating local timer
 cpu0: apic clock running at 99 MHz
 ioapic0 at mainbus0 apid 2 (I/O APIC)
 ioapic0: pa 0xfec00000, version 11, 24 pins
 vesabios0 at mainbus0: version 2.0, ATI Technologies Inc. RS3 
 vesafb0 at vesabios0: VESA frame buffer
 vesafb0: fb 1024x768x8 @0xe0000000
 vesafb0: VBE/PM 1.0 [standby] [suspend] [off]
 wsdisplay0 at vesafb0 kbdmux 1: console (fb, vt100 emulation)
 wsmux1: connecting to wsdisplay0
 acpi0 at mainbus0: Advanced Configuration and Power Interface
 acpi0: using Intel ACPI CA subsystem version 20060217
 acpi0: X/RSDT: OemId <XPC   ,AWRDACPI,42302e31>, AslId <AWRD,00000000>
 acpi0: SCI interrupting at int 9
 acpi0: fixed-feature power button present
 timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
 ACPI-Fast 32-bit timer
 mpacpi: could not get bus number, assuming bus 0
 ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
 ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
 acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
 PNP0C01 [System Board] at acpi0 not configured
 PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
 PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
 PNP0000 [AT Interrupt Controller] at acpi0 not configured
 PNP0200 [AT DMA Controller] at acpi0 not configured
 attimer1 at acpi0 (PNP0100): AT Timer
 attimer1: io 0x40-0x43 irq 0
 PNP0B00 [AT Real-Time Clock] at acpi0 not configured
 pcppi1 at acpi0 (PNP0800)
 pcppi1: io 0x61
 spkr0 at pcppi1
 sysbeep0 at pcppi1
 npx0 at acpi0 (PNP0C04)
 npx0: io 0xf0-0xff irq 13
 npx0: reported by CPUID; using exception 16
 PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
 com0 at acpi0 (PNP0501-1)
 com0: io 0x3f8-0x3ff irq 4
 com0: ns16550a, working fifo
 pckbc0 at acpi0 (PNP0F13): aux port
 pckbc0: irq 12
 pckbc1 at acpi0 (PNP0303): kbd port
 pckbc1: io 0x60,0x64 irq 1
 PNP0C0B [ACPI Fan] at acpi0 not configured
 acpitz0 at acpi0: ACPI Thermal Zone
 acpitz0: unable to get polling interval; using default of 30.0s
 acpitz0: active cooling level 0: 50.0C
 acpitz0: critical 60.0C passive -273.-3C
 apm0 at acpi0: Power Management spec V1.2
 pcppi1: attached to attimer1
 pckbd0 at pckbc1 (kbd slot)
 pckbc1: using irq 1 for kbd slot
 wskbd0 at pckbd0: console keyboard, using wsdisplay0
 pci0 at mainbus0 bus 0: configuration mode 1
 pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 pchb0 at pci0 dev 0 function 0
 pchb0: ATI Technologies RS300 Host Bridge (rev. 0x02)
 agp at pchb0 not configured
 ppb0 at pci0 dev 1 function 0: ATI Technologies RS300 AGP Interface (rev. 0x00)
 pci1 at ppb0 bus 1
 pci1: i/o space, memory space enabled
 ATI Technologies Radeon 9100 IGP (A4) (VGA display) at pci1 dev 5 function 0 
not configured
 ohci0 at pci0 dev 19 function 0: ATI Technologies SB200 USB Host Controller 
(rev. 0x01)
 ohci0: interrupting at ioapic0 pin 19 (irq 10)
 ohci0: OHCI version 1.0, legacy support
 usb0 at ohci0: USB revision 1.0
 uhub0 at usb0
 uhub0: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 3 ports with 3 removable, self powered
 ohci1 at pci0 dev 19 function 1: ATI Technologies SB200 USB Host Controller 
(rev. 0x01)
 ohci1: interrupting at ioapic0 pin 19 (irq 10)
 ohci1: OHCI version 1.0, legacy support
 usb1 at ohci1: USB revision 1.0
 uhub1 at usb1
 uhub1: ATI Technologie OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 3 ports with 3 removable, self powered
 ehci0 at pci0 dev 19 function 2: ATI Technologies SB200 USB2 Host Controller 
(rev. 0x01)
 ehci0: interrupting at ioapic0 pin 19 (irq 10)
 ehci0: BIOS has given up ownership
 ehci0: EHCI version 1.0
 ehci0: companion controllers, 3 ports each: ohci0 ohci1
 usb2 at ehci0: USB revision 2.0
 uhub2 at usb2
 uhub2: ATI Technologies EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 uhub2: 6 ports with 6 removable, self powered
 piixpm0 at pci0 dev 20 function 0: Power Management Controller
 piixpm0: interrupting at SMI
 iic0 at piixpm0: I2C bus
 ixpide0 at pci0 dev 20 function 1
 ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
 ixpide0: bus-master DMA support present
 ixpide0: primary channel configured to compatibility mode
 ixpide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
 atabus0 at ixpide0 channel 0
 ixpide0: secondary channel configured to compatibility mode
 ixpide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
 atabus1 at ixpide0 channel 1
 pcib0 at pci0 dev 20 function 3
 pcib0: ATI Technologies SB200 PCI-ISA Bridge (rev. 0x00)
 ppb1 at pci0 dev 20 function 4: ATI Technologies SB200 PCI-PCI Bridge (rev. 
0x00)
 pci2 at ppb1 bus 2
 pci2: i/o space, memory space enabled
 satalink0 at pci2 dev 5 function 0
 satalink0: Silicon Image SATALink 3512 (rev. 0x01)
 satalink0: SATALink BA5 register space disabled
 satalink0: bus-master DMA support present
 satalink0: primary channel wired to native-PCI mode
 satalink0: using ioapic0 pin 17 (irq 11) for native-PCI interrupt
 atabus2 at satalink0 channel 0
 satalink0: secondary channel wired to native-PCI mode
 atabus3 at satalink0 channel 1
 bce0 at pci2 dev 6 function 0: Broadcom BCM4401 10/100 Ethernet
 bce0: interrupting at ioapic0 pin 18 (irq 5)
 bmtphy0 at bce0 phy 1: BCM4401 10/100 media interface, rev. 0
 bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 bce0: Ethernet address 00:30:1b:b1:99:0e
 tlp0 at pci2 dev 7 function 0: DECchip 21140A Ethernet, pass 2.2
 tlp0: interrupting at ioapic0 pin 19 (irq 10)
 tlp0: Ethernet address 00:80:c8:27:f0:48
 lxtphy0 at tlp0 phy 0: LXT970 10/100 media interface, rev. 1
 lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 fwohci0 at pci2 dev 11 function 0: VIA Technologies VT6306 IEEE 1394 Host 
Controller (rev. 0x80)
 fwohci0: interrupting at ioapic0 pin 19 (irq 10)
 fwohci0: OHCI version 1.0 (ROM=1)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 00:30:1b:b1:00:00:99:72
 fwohci0: Phy 1394a available S400, 2 ports.
 fwohci0: Link S400, max_rec 2048 bytes.
 ieee1394if0 at fwohci0: IEEE1394 bus
 fwip0 at ieee1394if0: IP over IEEE1394
 fwohci0: Initiate bus reset
 auixp0 at pci0 dev 20 function 5: ATI Technologies IXP AC'97 Audio Controller 
(rev. 0x00)
 auixp0: interrupting at ioapic0 pin 17 (irq 5)
 auixp0: soft resetting aclink
 isa0 at pcib0
 ioapic0: enabling
 fwohci0: node_id=0xc800ffc1, gen=1, CYCLEMASTER mode
 ieee1394if0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
 ieee1394if0: bus manager 1 (me)
 timecounter: Timecounter "clockinterrupt" frequency 1024 Hz quality 0
 auixp0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
 auixp0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
 audio0 at auixp0: full duplex, mmap, independent
 auixp0: codec spdif support detected but disabled for now
 Kernelized RAIDframe activated
 ieee1394if0: New S400 device ID:00d04b4406070e56
 sbp0 at ieee1394if0: SBP-2/SCSI over IEEE1394
 scsibus0 at sbp0: 1 target, 0 luns per target
 sd0 at scsibus0 target 0 lun 0: <LaCie, LaCie Hard Drive, 0138> simplified 
direct fixed
 sd0: 76319 MB, 76319 cyl, 64 head, 32 sec, 512 bytes/sect x 156301488 sectors
 wd0 at atabus0 drive 0: <HDS728080PLAT20>
 wd0: drive supports 16-sector PIO transfers, LBA48 addressing
 wd0: 78533 MB, 159560 cyl, 16 head, 63 sec, 512 bytes/sect x 160836480 sectors
 wd0: 32-bit data port
 wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
 wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
 atapibus0 at atabus1: 2 targets
 cd0 at atapibus0 drive 0: <LITE-ON DVD SHD-16P1S, , GS02> cdrom removable
 cd0: 32-bit data port
 cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
 cd0(ixpide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
 raid3: RAID Level 1
 raid3: Components: /dev/sd0a component1[**FAILED**]
 raid3: Total Sectors: 156301312 (76319 MB)
 boot device: raid3
 root on raid3a dumps on raid3b
 root file system type: ffs
 wsdisplay0: screen 1 added (fb, vt100 emulation)
 wsdisplay0: screen 2 added (fb, vt100 emulation)
 wsdisplay0: screen 3 added (fb, vt100 emulation)
 wsdisplay0: screen 4 added (fb, vt100 emulation)
 raid3: Error re-writing parityd1
 tlp0: transmit underrun; new threshold: 96/256 bytes