port-i386/41584: NetBSD 5.0 (Jibbed liveCD) won't boot on Compaq Presario laptop unless ACPI + SMP both disabled

[rugxulo%gmail.com@localhost]

>Number:         41584
>Category:       port-i386
>Synopsis:       NetBSD 5.0 (Jibbed liveCD) won't boot on Compaq Presario 
>laptop unless ACPI + SMP both disabled
>Confidential:   no
>Severity:       non-critical
>Priority:       low
>Responsible:    port-i386-maintainer
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sat Jun 13 02:40:00 +0000 2009
>Originator:     Anthony Williams
>Release:        5.0 (Jibbed liveCD i386)
>Organization:
>Environment:
Don't know exactly (see below for dmesg output), but it's something like 
"NetBSD 5.0-RELEASE i386". My cpu is a Compaq Presario F572US (AMD64x2 1.7 Ghz, 
TK-53, 1 GB RAM, circa 2007).
>Description:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0_STABLE (JIBBED5) #0: Sat May  9 15:52:15 CEST 2009
        root%pembe.aydogan.net@localhost:/root/livecd/work/JIBBED5
total memory = 958 MB
avail memory = 931 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard Presario F500 (GF596UA#ABA)        (Rev 1)
mainbus0 (root)
cpu0 at mainbus0: AMD 686-class, 1707MHz, id 0x60f81
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x02f3 (RAM memory, revision 0xa2) at pci0 dev 0 function 
0 not configured
vendor 0x10de product 0x02fa (RAM memory, revision 0xa2) at pci0 dev 0 function 
1 not configured
vendor 0x10de product 0x02fe (RAM memory, revision 0xa2) at pci0 dev 0 function 
2 not configured
vendor 0x10de product 0x02f8 (RAM memory, revision 0xa2) at pci0 dev 0 function 
3 not configured
vendor 0x10de product 0x02f9 (RAM memory, revision 0xa2) at pci0 dev 0 function 
4 not configured
vendor 0x10de product 0x02ff (RAM memory, revision 0xa2) at pci0 dev 0 function 
5 not configured
Skipping broken PCI header on 0:0:5
vendor 0x10de product 0x027f (RAM memory, revision 0xa2) at pci0 dev 0 function 
6 not configured
vendor 0x10de product 0x027e (RAM memory, revision 0xa2) at pci0 dev 0 function 
7 not configured
ppb0 at pci0 dev 2 function 0: vendor 0x10de product 0x02fc (rev. 0xa1)
ppb0: disabling notification events
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 3 function 0: vendor 0x10de product 0x02fd (rev. 0xa1)
ppb1: disabling notification events
pci2 at ppb1 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x14e4 product 0x4311 (miscellaneous network, revision 0x02) at pci2 dev 
0 function 0 not configured
vga1 at pci0 dev 5 function 0: vendor 0x10de product 0x0247 (rev. 0xa2)
vga1: WARNING: ignoring 64-bit BAR @ 0x14
vga1: WARNING: ignoring 64-bit BAR @ 0x1c
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x10de product 0x0270 (RAM memory, revision 0xa2) at pci0 dev 9 function 
0 not configured
pcib0 at pci0 dev 10 function 0
pcib0: vendor 0x10de product 0x0260 (rev. 0xa3)
nfsmbc0 at pci0 dev 10 function 1: vendor 0x10de product 0x0264 (rev. 0xa3)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
spdmem0 at iic0 addr 0x50
spdmem0: DDR2 SDRAM memory, no parity or ECC, 512MB, 667MHz (PC2-5300)
spdmem0: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 3.00ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-5-5-15
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x51
spdmem1: DDR2 SDRAM memory, no parity or ECC, 512MB, 667MHz (PC2-5300)
spdmem1: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 3.00ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 5-5-5-15
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
vendor 0x10de product 0x0271 (Co-processor processor, revision 0xa3) at pci0 
dev 10 function 3 not configured
ohci0 at pci0 dev 11 function 0: vendor 0x10de product 0x026d (rev. 0xa3)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 11 function 1: vendor 0x10de product 0x026e (rev. 0xa3)
ehci0: interrupting at irq 7
ehci0: BIOS refuses to give up ownership, using force
ehci0: EHCI version 1.0
ehci0: companion controller, 8 ports each: ohci0
usb1 at ehci0: USB revision 2.0
viaide0 at pci0 dev 13 function 0
viaide0: NVIDIA nForce430 IDE Controller (rev. 0xf1)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel ignored (disabled)
viaide1 at pci0 dev 14 function 0
viaide1: NVIDIA nForce430 Serial ATA Controller (rev. 0xf1)
viaide1: bus-master DMA support present
viaide1: couldn't map sata regs
ppb2 at pci0 dev 16 function 0: vendor 0x10de product 0x026f (rev. 0xa2)
pci3 at ppb2 bus 7
pci3: i/o space, memory space enabled
azalia0 at pci0 dev 16 function 1: Generic High Definition Audio Controller
azalia0: interrupting at irq 11
azalia0: host: 0x10de/0x026c (rev. 162), HDA rev. 1.0
nfe0 at pci0 dev 20 function 0: vendor 0x10de product 0x0269 (rev. 0xa3)
nfe0: interrupting at irq 10
nfe0: Ethernet address 00:1b:24:4f:1f:4b
rlphy0 at nfe0 phy 1: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3
pchb3: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pms0: Synaptics touchpad version 6.3
pms0: Palm detect, Multi-finger
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: 0x14f1/0x5045 (rev. 1.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
atapibus0 at atabus0: 2 targets
uhub0 at usb0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
uhub1 at usb1: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
IPsec: Initialized Security Association Processing.
cd0 at atapibus0 drive 0: <Slimtype DVD A  DS8A1P, , CH63> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
boot device: cd0
root on cd0a
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: Sony USB Floppy Drive, rev 2.00/7.03, addr 2
umass0: using UFI over CBI with CCI
atapibus1 at umass0: 2 targets
atapibus1 drive 0: <SONY, USB-FDU, 7.03> disk removable not configured
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)

>How-To-Repeat:
Grab the 5.0 i386 liveCD from http://www.jibbed.org and try booting. It only 
boots if both ACPI *and* SMP are disabled, avoiding only one or the other 
doesn't work, it just hangs before reaching prompt.
>Fix:
No fix, but the workaround is to disable ACPI and SMP, e.g. use boot option #4 
(I think), then everything seems to work fine (besides the obvious lack of a 
second core, heh).