Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL status 3)

To: port-i386-maintainer%netbsd.org@localhost,gnats-admin%netbsd.org@localhost,netbsd-bugs%netbsd.org@localhost,dalibor.gudzic%gmail.com@localhost
Subject: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL status 3)
From: David Holland <dholland-bugs%netbsd.org@localhost>
Date: Sun, 13 Nov 2011 18:00:17 +0000 (UTC)
The following reply was made to PR port-i386/40507; it has been noted by GNATS.

From: David Holland <dholland-bugs%netbsd.org@localhost>
To: gnats-bugs%netbsd.org@localhost
Cc: 
Subject: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL
 status 3)
Date: Sun, 13 Nov 2011 17:59:58 +0000

 not sent to gnats (all bug database traffic should be sent to
 gnats-bugs; it remails from there)
 
    ------
 
 From: Dalibor Gudzic <dalibor.gudzic%gmail.com@localhost>
 To: port-i386-maintainer%netbsd.org@localhost, 
gnats-admin%netbsd.org@localhost,
        netbsd-bugs%netbsd.org@localhost
 Subject: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL
        status 3)
 Date: Thu, 10 Nov 2011 23:15:01 +0100
 
 On Sat, Oct 22, 2011 at 7:05 PM, Dalibor Gudzic
 <dalibor.gudzic%gmail.com@localhost> wrote:
 > The following reply was made to PR port-i386/40507; it has been noted by 
 > GNATS.
 >
 > From: Dalibor Gudzic <dalibor.gudzic%gmail.com@localhost>
 > To: gnats-bugs%netbsd.org@localhost
 > Cc: port-i386-maintainer%netbsd.org@localhost, 
 > netbsd-bugs%netbsd.org@localhost,
 > ? ? ? ?gnats-admin%netbsd.org@localhost
 > Subject: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL
 > ?status 3)
 > Date: Sat, 22 Oct 2011 19:03:11 +0200
 >
 > ?Hi,
 >
 > ?On Sat, Oct 22, 2011 at 5:26 PM, ?<jmcneill%netbsd.org@localhost> wrote:
 > ?> Synopsis: AR5005G - ath0: unable to attach hardware; HAL status 3
 > ?>
 > ?> State-Changed-From-To: open->feedback
 > ?> State-Changed-By: jmcneill%NetBSD.org@localhost
 > ?> State-Changed-When: Sat, 22 Oct 2011 15:26:49 +0000
 > ?> State-Changed-Why:
 > ?> can you re-test with -current?
 > ?>
 
 I tested with -current snapshot from about two weeks ago,
 unfortunately no joy. :( Here's the full dmesg:
 
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
     2006, 2007, 2008, 2009, 2010, 2011
     The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.
 
 NetBSD 5.99.56 (GENERIC) #0: Sat Oct 22 15:06:19 UTC 2011
        
builds%b8.netbsd.org@localhost:/home/builds/ab/HEAD/i386/201110220850Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
 total memory = 1406 MB
 avail memory = 1369 MB
 timecounter: Timecounters tick every 10.000 msec
 timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
 FUJITSU SIEMENS AMILO PRO V3515 (20)
 mainbus0 (root)
 cpu0 at mainbus0 apid 0: Intel(R) Celeron(R) M CPU        430  @
 1.73GHz, id 0x6e8
 ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 3, 24 pins
 ioapic1 at mainbus0 apid 2: pa 0xfecc0000, version 3, 24 pins
 acpi0 at mainbus0: Intel ACPICA 20110623
 acpi0: X/RSDT: OemId <FSC   ,PC      ,06040000>, AslId < LTP,00000000>
 acpi0: SCI interrupting at int 10
 timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
 acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
 acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
 NBPE (PNP0C01) at acpi0 not configured
 npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
 npx1: reported by CPUID; using exception 16
 attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
 pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
 midi0 at pcppi1: PC speaker
 sysbeep0 at pcppi1
 MEM (PNP0C01) at acpi0 not configured
 SYSR (PNP0C02) at acpi0 not configured
 pckbc1 at acpi0 (PS2M, STL3842) (aux port): irq 12
 pckbc2 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
 acpivga0 at acpi0 (VGA): ACPI Display Adapter
 acpiout0 at acpivga0 (CRT, 0x0100): ACPI Display Output Device
 acpiout1 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
 acpivga0: connected output devices:
 acpivga0:   0x0100 (acpiout0): Ext. Monitor, head 0, bios detect
 acpivga0:   0x0110 (acpiout1): LCD Panel, head 0, bios detect
 acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
 acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery
 acpifan0 at acpi0 (FAN, PNP0C0B): ACPI Fan
 acpitz0 at acpi0 (THRM): cpu0
 acpitz0: active cooling level 0: 59.8C
 acpitz0: levels: critical 109.8 C, passive 65.8 C
 apm0 at acpi0: Power Management spec V1.2
 attimer1: attached to pcppi1
 pckbd0 at pckbc2 (kbd slot)
 pckbc2: using irq 1 for kbd slot
 wskbd0 at pckbd0: console keyboard
 pms0 at pckbc2 (aux slot)
 pckbc2: using irq 12 for aux slot
 wsmouse0 at pms0 mux 0
 pci0 at mainbus0 bus 0: configuration mode 1
 pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 pchb0 at pci0 dev 0 function 0: vendor 0x1106 product 0x0364 (rev. 0x00)
 agp0 at pchb0: aperture at 0xc0000000, size 0x8000000
 pchb1 at pci0 dev 0 function 1: vendor 0x1106 product 0x1364 (rev. 0x00)
 pchb2 at pci0 dev 0 function 2: vendor 0x1106 product 0x2364 (rev. 0x00)
 pchb3 at pci0 dev 0 function 3: vendor 0x1106 product 0x3364 (rev. 0x00)
 pchb4 at pci0 dev 0 function 4: vendor 0x1106 product 0x4364 (rev. 0x00)
 vendor 0x1106 product 0x5364 (interrupt system, interface 0x20) at
 pci0 dev 0 function 5 not configured
 pchb5 at pci0 dev 0 function 6: vendor 0x1106 product 0x6364 (rev. 0x00)
 pchb6 at pci0 dev 0 function 7: vendor 0x1106 product 0x7364 (rev. 0x00)
 ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0xb198 (rev. 0x00)
 pci1 at ppb0 bus 1
 pci1: i/o space, memory space enabled, rd/line, wr/inv ok
 vga1 at pci1 dev 0 function 0: vendor 0x1106 product 0x3371 (rev. 0x01)
 wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
 wsmux1: connecting to wsdisplay0
 viadrm0 at vga1: VIA P4M900 / VN896
 viadrm0: AGP at 0xc0000000 128MB
 viadrm0: Initialized via 2.11.1 20070202
 ppb1 at pci0 dev 2 function 0: vendor 0x1106 product 0xa364 (rev. 0x80)
 ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
 pci2 at ppb1 bus 2
 pci2: i/o space, memory space enabled, rd/line, wr/inv ok
 ppb2 at pci0 dev 3 function 0: vendor 0x1106 product 0xc364 (rev. 0x80)
 ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
 pci3 at ppb2 bus 3
 pci3: i/o space, memory space enabled, rd/line, wr/inv ok
 viaide0 at pci0 dev 15 function 0: VIA Technologies VT8237A SATA
 Controller (rev. 0x80)
 viaide0: bus-master DMA support present
 viaide0: primary channel configured to native-PCI mode
 viaide0: using ioapic0 pin 21 for native-PCI interrupt
 atabus0 at viaide0 channel 0
 viaide0: secondary channel configured to native-PCI mode
 atabus1 at viaide0 channel 1
 viaide1 at pci0 dev 15 function 1
 viaide1: VIA Technologies VT8237A ATA133 controller
 viaide1: bus-master DMA support present
 viaide1: primary channel configured to compatibility mode
 viaide1: primary channel ignored (disabled)
 viaide1: secondary channel configured to compatibility mode
 viaide1: secondary channel interrupting at ioapic0 pin 15
 atabus2 at viaide1 channel 1
 uhci0 at pci0 dev 16 function 0: vendor 0x1106 product 0x3038 (rev. 0xa0)
 uhci0: interrupting at ioapic0 pin 20
 usb0 at uhci0: USB revision 1.0
 uhci1 at pci0 dev 16 function 1: vendor 0x1106 product 0x3038 (rev. 0xa0)
 uhci1: interrupting at ioapic0 pin 22
 usb1 at uhci1: USB revision 1.0
 uhci2 at pci0 dev 16 function 2: vendor 0x1106 product 0x3038 (rev. 0xa0)
 uhci2: interrupting at ioapic0 pin 21
 usb2 at uhci2: USB revision 1.0
 uhci3 at pci0 dev 16 function 3: vendor 0x1106 product 0x3038 (rev. 0xa0)
 uhci3: interrupting at ioapic0 pin 23
 usb3 at uhci3: USB revision 1.0
 ehci0 at pci0 dev 16 function 4: vendor 0x1106 product 0x3104 (rev. 0x86)
 ehci0: interrupting at ioapic0 pin 21
 ehci0: dropped intr workaround enabled
 ehci0: BIOS has given up ownership
 ehci0: EHCI version 1.0
 ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
 usb4 at ehci0: USB revision 2.0
 viapcib0 at pci0 dev 17 function 0: vendor 0x1106 product 0x3337 (rev. 0x00)
 viapcib0: SMBus found at 0x4100 (revision 0x0)
 iic0 at viapcib0: I2C bus
 pchb7 at pci0 dev 17 function 7: vendor 0x1106 product 0x287e (rev. 0x00)
 vr0 at pci0 dev 18 function 0: vendor 0x1106 product 0x3065 (rev. 0x7c)
 vr0: interrupting at ioapic0 pin 23
 vr0: Ethernet address: 00:14:0b:08:64:5b
 ukphy0 at vr0 phy 1: OUI 0x0002c6, model 0x0032, rev. 10
 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 ppb3 at pci0 dev 19 function 0: vendor 0x1106 product 0x337b (rev. 0x00)
 pci4 at ppb3 bus 4
 pci4: i/o space, memory space enabled
 hdaudio0 at pci4 dev 1 function 0: HD Audio Controller
 hdaudio0: interrupting at ioapic0 pin 17
 hdafg0 at hdaudio0: Conexant CX20549
 hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
 hdafg0: ADC01 2ch: Mic In [Jack] [Built-In]
 hdafg0: DIG02 2ch: SPDIF Out [Jack]
 hdafg0: 2ch/2ch 48000Hz 96000Hz PCM16 PCM20 PCM24 AC3
 audio0 at hdafg0: full duplex, playback, capture, independent
 hdvsmfg at hdaudio0 not configured
 ppb4 at pci0 dev 19 function 1: vendor 0x1106 product 0x337a (rev. 0x00)
 pci5 at ppb4 bus 5
 pci5: i/o space, memory space enabled
 ath0 at pci5 dev 1 function 0: Atheros 2413
 ath0: interrupting at ioapic0 pin 18
 ath0: unable to attach hardware; HAL status 3
 isa0 at viapcib0
 isapnp0 at isa0 port 0x279
 isapnp0: no ISA Plug 'n Play devices found
 acpicpu0 at cpu0: ACPI CPU
 acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
 acpicpu0: C2: I/O, lat   1 us, pow   500 mW, bus master check
 coretemp0 at cpu0: thermal sensor, 1 C resolution
 timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
 timecounter: Timecounter "TSC" frequency 1729214890 Hz quality 3000
 acpiacad0: AC adapter online.
 uhub0 at usb0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered
 uhub1 at usb1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 2 ports with 2 removable, self powered
 uhub2 at usb2: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub2: 2 ports with 2 removable, self powered
 uhub3 at usb3: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub3: 2 ports with 2 removable, self powered
 uhub4 at usb4: vendor 0x1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 uhub4: 8 ports with 8 removable, self powered
 viaide0 port 0: device present, speed: 1.5Gb/s
 wd0 at atabus0 drive 0
 wd0: <WDC WD600BEVS-07LAT0>
 wd0: drive supports 16-sector PIO transfers, LBA48 addressing
 wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
 wd0: 32-bit data port
 wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
 wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
 ehci0: handing over low speed device on port 2 to uhci0
 atapibus0 at atabus2: 2 targets
 cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T10N, M006BM21412,
 PW02> cdrom removable
 cd0: 32-bit data port
 cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
 cd0(viaide1:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
 Kernelized RAIDframe activated
 boot device: cd0
 root on cd0a dumps on cd0b
 root file system type: cd9660
 warning: no /dev/console
 uhidev0 at uhub0 port 2 configuration 1 interface 0
 uhidev0: vendor 0x15d9 USB Mouse, rev 1.10/1.00, addr 2, iclass 3/1
 ums0 at uhidev0: 3 buttons and Z dir
 wsmouse1 at ums0 mux 0
 
 
 I am available for any further testing or more info.
 
 All best
Prev by Date: Re: kern/45425: how to restore traditional unix behaviour for slashes on the end of pathnames
Next by Date: Re: kern/41957 (hdaudio failure (was: azalia crashes during boot))
Previous by Thread: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL status 3)
Next by Thread: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL status 3)
Indexes:
Home | Main Index | Thread Index | Old Index