NetBSD-Bugs archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: port-cobalt/53054: panic when booting with latest kernel from HEAD & 5.1.2 userland



The following reply was made to PR port-cobalt/53054; it has been noted by GNATS.

From: Sevan Janiyan <venture37%geeklan.co.uk@localhost>
To: gnats-bugs%NetBSD.org@localhost
Cc: 
Subject: Re: port-cobalt/53054: panic when booting with latest kernel from
 HEAD & 5.1.2 userland
Date: Sun, 25 Feb 2018 15:09:01 +0000

 On 25/02/2018 14:30, coypu%sdf.org@localhost wrote:
 >  does a netbsd-8 kernel work? I think the recent shared pmap changes
 >  might have made it broken
 
 Yes, netbsd-8 worked.
 
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
     The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.
 
 NetBSD 8.0_BETA (GENERIC.201802250030Z)
 Cobalt Qube 2
 total memory = 256 MB
 avail memory = 247 MB
 timecounter: Timecounters tick every 10.000 msec
 Kernelized RAIDframe activated
 mainbus0 (root)
 com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
 com0: console
 cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU
 Rev. 10.0
 cpu0: 48 TLB entries, 16MB max page size
 cpu0: 32KB/32B 2-way set-associative L1 instruction cache
 cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
 mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
 panel0 at mainbus0 addr 0x1f000000
 gt0 at mainbus0 addr 0x14000000
 pci0 at gt0
 pci0: i/o space, memory space enabled, rd/line, wr/inv ok
 pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
 tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
 tlp0: interrupting at level 1
 tlp0: Ethernet address 00:10:e0:
 lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
 lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 pcib0 at pci0 dev 9 function 0
 pcib0: vendor 1106 product 0586, rev 39
 viaide0 at pci0 dev 9 function 1
 viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
 viaide0: bus-master DMA support present
 viaide0: primary channel configured to compatibility mode
 viaide0: primary channel interrupting at irq 14
 atabus0 at viaide0 channel 0
 viaide0: secondary channel configured to compatibility mode
 viaide0: secondary channel interrupting at irq 15
 atabus1 at viaide0 channel 1
 vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x02) at pci0
 dev 9 function 2 not configured
 vendor 10b9 product 5237 (USB serial bus, OHCI, revision 0x03) at pci0
 dev 10 function 0 not configured
 vendor 10b9 product 5237 (USB serial bus, OHCI, revision 0x03) at pci0
 dev 10 function 1 not configured
 vendor 10b9 product 5237 (USB serial bus, OHCI, revision 0x03) at pci0
 dev 10 function 2 not configured
 vendor 10b9 product 5239 (USB serial bus, EHCI, revision 0x01) at pci0
 dev 10 function 3 not configured
 vendor 10b9 product 5253 (IEEE1394 serial bus, OpenHCI) at pci0 dev 10
 function 4 not configured
 tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
 tlp1: interrupting at level 2
 tlp1: Ethernet address 00:10:e0:
 lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
 lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
 timecounter: Timecounter "mips3_cp0_counter" frequency 125000000 Hz
 quality 100
 wd0 at atabus0 drive 0
 wd0: <HDS728080PLAT20>
 wd0: drive supports 16-sector PIO transfers, LBA48 addressing
 wd0: 78532 MB, 159557 cyl, 16 head, 63 sec, 512 bytes/sect x 160834367
 sectors
 wd0: 32-bit data port
 wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
 wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
 boot device: wd0
 root on wd0a dumps on wd0b
 root file system type: ffs
 kern.module.path=/stand/cobalt/8.0/modules
 pid 1(init): ABI set to O32 (e_flags=0x1007)
 


Home | Main Index | Thread Index | Old Index