port-i386/53494: vte doesn't work on eBox 3352DX3-AP

To: port-i386-maintainer%netbsd.org@localhost,gnats-admin%netbsd.org@localhost,netbsd-bugs%netbsd.org@localhost
Subject: port-i386/53494: vte doesn't work on eBox 3352DX3-AP
From: vezhlys%gmail.com@localhost
Date: Thu, 2 Aug 2018 21:05:00 +0000 (UTC)

>Number:         53494
>Category:       port-i386
>Synopsis:       vte doesn't work on eBox 3352DX3-AP
>Confidential:   no
>Severity:       serious
>Priority:       low
>Responsible:    port-i386-maintainer
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Thu Aug 02 21:05:00 +0000 2018
>Originator:     Andrius V
>Release:        current
>Organization:
>Environment:
NetBSD vertexpc 8.99.22 NetBSD 8.99.22 (GENERIC) #0: Fri Jul 27 16:12:40 UTC 2018  mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC i386
>Description:
Hello,

I recently received eBox 3352DX3-AP system which is based on VortexDX3 CPU. I am facing an issue with R6040 Ethernet controller on it. It can't set a media type (even if I am trying to set supported one manually) and it doesn't have any status value, dhcpcd sets some incorrect IP and I can't access the network. ifconfig vte0:
vte0: flags=0x8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        ec_capabilities=1<VLAN_MTU>
        ec_enabled=0
        address: xx:xx:xx:xx:xx:xx
        media: Ethernet autoselect (none)
        inet 169.254.69.13/16 broadcast 169.254.255.255 flags 0x0
        inet6 fe80::7257:8bd0:b0fa:afc0%vte0/64 flags 0x0 scopeid 0x1

General phy attaches to it (not a rdcphy) because it has different OUI and model. But even if I would register new OUI and model to rdcphy, it wouldn't change the behavior. 

I am booting system without ACPI and SMP (it fails to boot with those because of other issue I still need to report). I tried controller on FreeBSD and Linux as well. FreeBSD seems to have the same issue, Linux works though. Please see dmesg below (there is also USB D-Link network card attached, it works):
NetBSD 8.99.22 (GENERIC) #0: Fri Jul 27 16:12:40 UTC 2018
	mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC
total memory = 1983 MB
avail memory = 1930 MB
rnd: seeded with 128 bits
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
RDC Semiconductor Co., Ltd. EMKORE                 (1.0                   )
mainbus0 (root)
cpu0 at mainbus0
cpu0: Vortex86DX3, id 0x611
cpu0: package 0, core 0, smt 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 17f3 product 6023 (rev. 0x02)
ppb0 at pci0 dev 1 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb0: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 2 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb1: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
pcib0 at pci0 dev 7 function 0: vendor 17f3 product 6035 (rev. 0x01)
pcib1 at pci0 dev 7 function 1: vendor 17f3 product 6035 (rev. 0x01)
vte0 at pci0 dev 8 function 0: vendor 17f3 product 6040 (rev. 0x00)
vte0: Ethernet address xx:xx:xx:xx:xx:xx
vte0: interrupting at irq 5
ukphy0 at vte0 phy 1: OUI 0xfcff2f, model 0x0005, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0 at pci0 dev 10 function 0: vendor 17f3 product 6060 (rev. 0x14)
ohci0: interrupting at irq 14
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 10 function 1: vendor 17f3 product 6061 (rev. 0x08)
ehci0: interrupting at irq 7
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: 1 companion controller, 4 ports: ohci0
usb1 at ehci0: USB revision 2.0
rdcide0 at pci0 dev 12 function 0: RDC R1012 IDE controller (rev. 0x02)
rdcide0: bus-master DMA support present
rdcide0: primary channel configured to native-PCI mode
rdcide0: using irq 15 for native-PCI interrupt
atabus0 at rdcide0 channel 0
rdcide0: secondary channel configured to native-PCI mode
rdcide0: secondary channel ignored (disabled)
vga0 at pci0 dev 13 function 0: vendor 17f3 product 2015 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
hdaudio0 at pci0 dev 14 function 0: HD Audio Controller
hdaudio0: interrupting at irq 14
hdafg0 at hdaudio0: vendor 10ec product 0262
hdafg0: DAC00 2ch: Speaker [Jack]
hdafg0: DIG01 2ch: Digital Out [Jack]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: ADC03 2ch: Line In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdafg0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
hdafg0: Latency: 128 milliseconds
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer0: attached to pcppi0
isa at pcib1 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb1: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
IPsec: Initialized Security Association Processing.
axen0 at uhub1 port 1
axen0: D-Link Elec. Corp. (0x2001) D-Link DUB-1312 (0x4a00), rev 2.10/1.00, addr 2
axen0: AX88179
axen0: Ethernet address xx:xx:xx:xx:xx:xx
rgephy0 at axen0 phy 3: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 5
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
ehci0: handing over low speed device on port 3 to ohci0
wd0 at atabus0 drive 0
wd0: <SS16G D0 RDC SD-IDE HOST CONTROLLER>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 15193 MB, 30869 cyl, 16 head, 63 sec, 512 bytes/sect x 31116288 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(rdcide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/i386/8.99.22/modules
uhidev0 at uhub0 port 3 configuration 1 interface 0
uhidev0: USB (0x1c4f) USB Keykoard (0x02), rev 1.10/1.10, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 Variable keys, 6 Array codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub0 port 3 configuration 1 interface 1
uhidev1: USB (0x1c4f) USB Keykoard (0x02), rev 1.10/1.10, addr 2, iclass 3/0
uhidev1: 2 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

>How-To-Repeat:
Boot system and run dhcpcd client for vte0.
>Fix:

Follow-Ups:
- Re: port-i386/53494: vte doesn't work on eBox 3352DX3-AP
  - From: Andrius V

Prev by Date: NetBSD Nightly Trouble Ticket Report
Next by Date: lib/53495: sched_get_priority_max/sched_get_priority_min not returning useful values
Previous by Thread: kern/53493: mouse keeps re-attaching using amd64 8.0 boot.iso CD
Next by Thread: Re: port-i386/53494: vte doesn't work on eBox 3352DX3-AP
Indexes:

Home | Main Index | Thread Index | Old Index