NetBSD-Bugs archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: port-sparc64/54211: esiop stopped detecting boot disk



The following reply was made to PR port-sparc64/54211; it has been noted by GNATS.

From: Tobias Ulmer <tobiasu%tmux.org@localhost>
To: gnats-bugs%netbsd.org@localhost
Cc: 
Subject: Re: port-sparc64/54211: esiop stopped detecting boot disk
Date: Sat, 18 May 2019 18:47:19 +0200

 On Sat, May 18, 2019 at 03:50:01PM +0000, Martin Husemann wrote:
 > The following reply was made to PR port-sparc64/54211; it has been noted by GNATS.
 > 
 > From: Martin Husemann <martin%duskware.de@localhost>
 > To: gnats-bugs%netbsd.org@localhost
 > Cc: 
 > Subject: Re: port-sparc64/54211: esiop stopped detecting boot disk
 > Date: Sat, 18 May 2019 17:46:44 +0200
 > 
 >  Are you using a self build kernel or one from the auto builds?
 
 auto build.
 
 Loading netbsd-INSTALL.gz: 9666680+9916240+344280=0x15c9870
 [   1.0000000] ksyms: Symbol table not found
 [   1.0000000] ksyms: String table not found
 [   1.0000000] ksyms: Perhaps the kernel is stripped?
 [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
 [   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
 [   1.0000000]     2018, 2019 The NetBSD Foundation, Inc.  All rights reserved.
 [   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
 [   1.0000000]     The Regents of the University of California.  All rights reserved.
 
 [   1.0000000] NetBSD 8.99.41 (INSTALL) #0: Fri May 17 23:51:35 UTC 2019
 [   1.0000000]  mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/sparc64/compile/INSTALL
 [   1.0000000] total memory = 16384 MB
 [   1.0000000] avail memory = 16062 MB
 [   1.0000000] running cgd selftest aes-xts-256 aes-xts-512 done
 [   1.0000000] mainbus0 (root): SUNW,Sun-Blade-2500 (Sun Blade 2500): hostid 83785822
 [   1.0000000] cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1280 MHz, CPU id 0
 [   1.0000000] cpu0: manuf 3e, impl 16, mask 24
 [   1.0000000] cpu0: system tick frequency 12 MHz
 [   1.0000000] cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
 [   1.0000000] cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1280 MHz, CPU id 1
 [   1.0000000] cpu1: manuf 3e, impl 16, mask 24
 [   1.0000000] cpu1: system tick frequency 12 MHz
 [   1.0000000] cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
 [   1.0000000] memory-controller at mainbus0 not configured
 [   1.0000000] memory-controller at mainbus0 not configured
 [   1.0000000] schizo0 at mainbus0: addr 4000e600000: Tomatillo, version 4, ign 700, bus A 0 to 0
 [   1.0000000] schizo0:  pci0 at schizo0
 [   1.0000000] bge0 at pci0 dev 3 function 0: Broadcom BCM5703 Gigabit Ethernet
 [   1.0000000] bge0: interrupting at ivec 371c
 [   1.0000000] bge0: HW config 00000000, 00000000, 00000000, 00000000 00000000
 [   1.0000000] bge0: ASIC BCM5702/5703 A2 (0x1002), Ethernet address 00:03:ba:78:58:22
 [   1.0000000] brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
 [   1.0000000] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
 [   1.0000000] ppm at mainbus0 not configured
 [   1.0000000] schizo1 at mainbus0: addr 4000ef00000: Tomatillo, version 4, ign 740, bus B 0 to 0
 [   1.0000000] schizo1:  pci1 at schizo1
 [   1.0000000] esiop0 at pci1 dev 4 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi)
 [   1.0000000] esiop0: using on-board RAM
 [   1.0000000] esiop0: interrupting at ivec 1f69
 [   1.0000000] scsibus0 at esiop0: 16 targets, 8 luns per target
 [   1.0000000] esiop1 at pci1 dev 4 function 1: Symbios Logic 53c1010-66 (ultra3-wide scsi)
 [   1.0000000] esiop1: using on-board RAM
 [   1.0000000] esiop1: interrupting at ivec 1f68
 [   1.0000000] scsibus1 at esiop1: 16 targets, 8 luns per target
 [   1.0000000] schizo2 at mainbus0: addr 4000f600000: Tomatillo, version 4, ign 780, bus A 0 to 1
 [   1.0000000] schizo2:  pci2 at schizo2
 [   1.0000000] ebus0 at pci2 dev 7 function 0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
 [   1.0000000] flashprom at ebus0 addr 0-fffff not configured
 [   1.0000000] rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819p
 [   1.0000000] pcfiic0 at ebus0 addr 320-321 ipl 2e
 [   1.0000000] iic0 at pcfiic0: I2C bus
 [   1.0000000] i2c-bridge at iic0 addr 0x09 not configured
 [   1.0000000] admtemp0 at iic0 addr 0x18: LM84 temperature sensor
 [   1.0000000] dbcool0 at iic0 addr 0x2c
 [   1.0000000] dbcool0: ADM1031 dBCool(tm) Controller (rev 0x0083)
 [   1.0000000] dbcool1 at iic0 addr 0x2e
 [   1.0000000] dbcool1: ADM1031 dBCool(tm) Controller (rev 0x0083)
 [   1.0000000] gpio at iic0 addr 0x37 not configured
 [   1.0000000] lmtemp0 at iic0 addr 0x4e: gpio LM75 Temperature Sensor
 [   1.0000000] lmtemp0: unable to read Tos register
 [   1.0000000] seeprom0 at iic0 addr 0x50: audio-card-fru-prom: size 8192
 [   1.0000000] seeprom1 at iic0 addr 0x51: motherboard-fru-prom: size 8192
 [   1.0000000] seeprom2 at iic0 addr 0x54: scsi-backplane-fru-prom: size 8192
 [   1.0000000] spdmem0 at iic0 addr 0x5b
 [   1.0000000] spdmem0: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem1 at iic0 addr 0x5c
 [   1.0000000] spdmem1: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem2 at iic0 addr 0x5d
 [   1.0000000] spdmem2: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem3 at iic0 addr 0x5e
 [   1.0000000] spdmem3: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem4 at iic0 addr 0x63
 [   1.0000000] spdmem4: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem5 at iic0 addr 0x64
 [   1.0000000] spdmem5: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem6 at iic0 addr 0x65
 [   1.0000000] spdmem6: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] spdmem7 at iic0 addr 0x66
 [   1.0000000] spdmem7: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200)
 [   1.0000000] clock-generator at iic0 addr 0x69 not configured
 [   1.0000000] power at ebus0 addr 800-82f ipl 20 not configured
 [   1.0000000] com0 at ebus0 addr 3f8-3ff ipl 2c: ns16550a, working fifo
 [   1.0000000] com0: console
 [   1.0000000] com1 at ebus0 addr 2e8-2ef ipl 2c: ns16550a, working fifo
 [   1.0000000] dma at ebus0 addr 0-ffff not configured
 [   1.0000000] alipm0 at pci2 dev 6 function 0: 223KHz clock
 [   1.0000000] iic1 at alipm0: I2C bus
 [   1.0000000] card-reader at iic1 addr 0x20 not configured
 [   1.0000000] autri0 at pci2 dev 8 function 0: Acer Labs M5451 AC-Link Controller Audio Device (rev. 0x02)
 [   1.0000000] autri0: interrupting at ivec 7a4
 [   1.0000000] autri0: ac97: Analog Devices AD1881A codec; headphone, Analog Devices Phat Stereo
 [   1.0000000] audio0 at autri0: full duplex, playback, capture, mmap, independent
 [   1.0000000] audio0: slinear_be:16 -> slinear_le:16 2ch 48000Hz, blk 40ms for playback
 [   1.0000000] audio0: slinear_be:16 <- slinear_le:16 2ch 48000Hz, blk 40ms for recording
 [   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
 [   1.0000000] wsbell at spkr0 not configured
 [   1.0000000] midi0 at autri0: 4DWAVE MIDI UART
 [   1.0000000] ohci0 at pci2 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
 [   1.0000000] ohci0: interrupting at ivec 7a7
 [   1.0000000] ohci0: OHCI version 1.0, legacy support
 [   1.0000000] usb0 at ohci0: USB revision 1.0
 [   1.0000000] ohci1 at pci2 dev 11 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
 [   1.0000000] ohci1: interrupting at ivec 7a6
 [   1.0000000] ohci1: OHCI version 1.0, legacy support
 [   1.0000000] usb1 at ohci1: USB revision 1.0
 [   1.0000000] aceride0 at pci2 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc4)
 [   1.0000000] aceride0: using ivec 1f98 for native-PCI interrupt
 [   1.0000000] atabus0 at aceride0 channel 0
 [   1.0000000] atabus1 at aceride0 channel 1
 [   1.0000000] ppb0 at pci2 dev 4 function 0: Texas Instruments product ac23 (rev. 0x02)
 [   1.0000000] pci3 at ppb0 bus 1
 [   1.0000000] ohci2 at pci3 dev 8 function 0: NEC USB Host Controller (rev. 0x43)
 [   1.0000000] ohci2: interrupting at ivec 794
 [   1.0000000] ohci2: OHCI version 1.0
 [   1.0000000] usb2 at ohci2: USB revision 1.0
 [   1.0000000] ohci3 at pci3 dev 8 function 1: NEC USB Host Controller (rev. 0x43)
 [   1.0000000] ohci3: interrupting at ivec 795
 [   1.0000000] ohci3: OHCI version 1.0
 [   1.0000000] usb3 at ohci3: USB revision 1.0
 [   1.0000000] ehci0 at pci3 dev 8 function 2: NEC USB2 Host Controller (rev. 0x04)
 [   1.0000000] ehci0: interrupting at ivec 796
 [   1.0000000] ehci0: 2 companion controllers, 3 ports each: ohci2 ohci3
 [   1.0000000] usb4 at ehci0: USB revision 2.0
 [   1.0000000] fwohci0 at pci3 dev 11 function 0: Texas Instruments TSB43AA23 IEEE 1394 Host Controller (rev. 0x00)
 [   1.0000000] fwohci0: interrupting at ivec 797
 [   1.0000000] fwohci0: OHCI version 1.10 (ROM=1)
 [   1.0000000] fwohci0: No. of Isochronous channels is 4.
 [   1.0000000] fwohci0: EUI64 00:05:16:00:00:71:1e:d4
 [   1.0000000] fwohci0: Phy 1394a available S400, 3 ports.
 [   1.0000000] fwohci0: Link S400, max_rec 2048 bytes.
 [   1.0000000] ieee1394if0 at fwohci0: IEEE1394 bus
 [   1.0000000] fwip0 at ieee1394if0: IP over IEEE1394
 [   1.0000000] fwohci0: Initiate bus reset
 [   1.0000000] ppm at mainbus0 not configured
 [   1.0000000] schizo3 at mainbus0: addr 4000ff00000: Tomatillo, version 4, ign 7c0, bus B 0 to 0
 [   1.0000000] schizo3:  pci4 at schizo3
 [   1.0000000] radeonfb0 at pci4 dev 2 function 0: ATI Technologies Radeon 7000/VE QY (rev. 0x00)
 [   1.0000000] radeonfb0: 64 MB aperture at 0x08000000, 64 KB registers at 0x00100000
 [   1.0000000] radeonfb0: display 0: initial virtual resolution 640x480 at 8 bpp
 [   1.0000000] radeonfb0: using 32 MB per display
 [   1.0000000] radeonfb0: port 0: physical 1024x768 60Hz
 [   1.0000000] radeonfb0: port 1: physical 1024x768 60Hz
 [   1.0000000] wsdisplay1 at radeonfb0 kbdmux 1
 [   1.0000000] drm at radeonfb0 not configured
 [   1.0000000] jbusi2c0 at mainbus0: addr 4000fc64000
 [   1.0000000] iic2 at jbusi2c0: I2C bus
 [   1.0000000] seeprom3 at iic2 addr 0x57: nvram: size 8192
 [   1.0000000] pcons at mainbus0 not configured
 [   1.0000000] fwohci0: BUS reset
 [   1.0000000] fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
 [   1.0000000] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
 [   1.0000000] ieee1394if0: bus manager 0
 [   1.0000169] No counter-timer -- using %stick at 12MHz as system clock.
 [   1.9139563] scsibus0: waiting 2 seconds for devices to settle...
 [   1.9139563] scsibus1: waiting 2 seconds for devices to settle...
 [   2.1300193] uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
 [   2.2400183] uhub1 at usb1: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
 [   2.3458517] uhub2 at usb2: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
 [   2.4500225] uhub3 at usb3: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
 [   2.5538013] uhub4 at usb4: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
 [   8.6300186] WARNING: 1 error while detecting hardware; check system log.
 [   8.7160060] root on md0a dumps on md0b
 [   8.7607141] root file system type: ffs
 [   8.8054243] kern.module.path=/stand/sparc64/8.99.41/modules
 erase ^?, werase ^W, kill ^U, intr ^C
 


Home | Main Index | Thread Index | Old Index