kern/54317: System hang during boot

[Thomas Klausner <wiz%NetBSD.org@localhost>]

>Number:         54317
>Category:       kern
>Synopsis:       System hang during boot
>Confidential:   no
>Severity:       critical
>Priority:       high
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sat Jun 22 11:15:00 +0000 2019
>Originator:     Thomas Klausner
>Release:        NetBSD 8.0.1/8.99.46
>Organization:
Curiosity is the very basis of education and if you tell me that
curiosity killed the cat, I say only that the cat died nobly.
- Arnold Edinborough
>Environment:
	
	
Architecture: x86_64
Machine: amd64
>Description:
I've installed a new system (old hardware from around 2010).
First I tried NetBSD 8.1. sysinst worked fine, but the boot stops after the line
Checking file systems:

The USB keyboard could not break into the debugger.

Then I tried 8.99.46 with a prebuilt daily snapshot. Installation, again, worked
fine, this time boot stops after the line:
Setting tty flags.

I've attached a PS/2 keyboard in the meantime, but I can't break into the debugger
with it either. (Nothing happens when I press ctrl-alt-esc).

This is repeatable very time.
>How-To-Repeat:
Boot this system:

[     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
[     1.000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
[     1.000000] 2018, 2019 The NetBSD Foundation, Inc.  All rights reserved.
[     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[     1.000000] The Regents of the University of California.  All rights reserved.

[     1.000000] NetBSD 8.99.45 (GENERIC) #0: Sat Jun 15 15:22:56 UTC 2019
[     1.000000] 	mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/amd64/compile/GENERIC
[     1.000000] total memory = 12279 MB
[     1.000000] avail memory = 11897 MB
[     1.000000] timecounter: Timecounters tick every 10.000 msec
[     1.000000] Kernelized RAIDframe activated
[     1.000000] running cgd selftest aes-xts-256 aes-xts-512 done
[     1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[     1.000003] System manufacturer System Product Name (System Version)
[     1.000003] mainbus0 (root)
[     1.000003] ACPI: RSDP 0x00000000000FB2C0 000014 (v00 ACPIAM)
[     1.000003] ACPI: RSDT 0x00000000BF780000 000040 (v01 092410 RSDT1941 20100924 MSFT 00000097)
[     1.000003] ACPI: FACP 0x00000000BF780200 000084 (v01 092410 FACP1941 20100924 MSFT 00000097)
[     1.000003] ACPI: DSDT 0x00000000BF7804B0 00B119 (v01 A1095  A1095001 00000001 INTL 20060113)
[     1.000003] ACPI: FACS 0x00000000BF798000 000040
[     1.000003] ACPI: APIC 0x00000000BF780390 0000D8 (v01 092410 APIC1941 20100924 MSFT 00000097)
[     1.000003] ACPI: MCFG 0x00000000BF780470 00003C (v01 092410 OEMMCFG  20100924 MSFT 00000097)
[     1.000003] ACPI: OEMB 0x00000000BF798040 000072 (v01 092410 OEMB1941 20100924 MSFT 00000097)
[     1.000003] ACPI: HPET 0x00000000BF78F4B0 000038 (v01 092410 OEMHPET  20100924 MSFT 00000097)
[     1.000003] ACPI: OSFR 0x00000000BF78F4F0 0000B0 (v01 092410 OEMOSFR  20100924 MSFT 00000097)
[     1.000003] ACPI: SSDT 0x00000000BF79A510 000363 (v01 DpgPmm CpuPm    00000012 INTL 20060113)
[     1.000003] ACPI: 2 ACPI AML tables successfully acquired and loaded
[     1.000003] ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 0x20, 24 pins
[     1.000003] ioapic1 at mainbus0 apid 9: pa 0xfec8a000, version 0x20, 24 pins
[     1.000003] cpu0 at mainbus0 apid 0
[     1.000003] cpu0: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu0: package 0, core 0, smt 0
[     1.000003] cpu1 at mainbus0 apid 2
[     1.000003] cpu1: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu1: package 0, core 1, smt 0
[     1.000003] cpu2 at mainbus0 apid 4
[     1.000003] cpu2: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu2: package 0, core 2, smt 0
[     1.000003] cpu3 at mainbus0 apid 6
[     1.000003] cpu3: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu3: package 0, core 3, smt 0
[     1.000003] cpu4 at mainbus0 apid 1
[     1.000003] cpu4: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu4: package 0, core 0, smt 1
[     1.000003] cpu5 at mainbus0 apid 3
[     1.000003] cpu5: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu5: package 0, core 1, smt 1
[     1.000003] cpu6 at mainbus0 apid 5
[     1.000003] cpu6: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu6: package 0, core 2, smt 1
[     1.000003] cpu7 at mainbus0 apid 7
[     1.000003] cpu7: Intel(R) Xeon(R) CPU           W3565  @ 3.20GHz, id 0x106a5
[     1.000003] cpu7: package 0, core 3, smt 1
[     1.000003] acpi0 at mainbus0: Intel ACPICA 20190405
[     1.000003] acpi0: X/RSDT: OemId <092410,RSDT1941,20100924>, AslId <MSFT,00000097>
[     1.000003] acpi0: MCFG: segment 0, bus 0-255, address 0x00000000e0000000
[     1.000003] ACPI: Dynamic OEM Table Load:
[     1.000003] ACPI: SSDT 0xFFFFC10015D15000 00244C (v01 DpgPmm P001Ist  00000011 INTL 20060113)
[     1.000003] acpi0: SCI interrupting at int 9
[     1.000003] acpi0: fixed power button present
[     1.000003] timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
[     1.044083] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[     1.044083] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[     1.044331] IOH (PNP0C01) at acpi0 not configured
[     1.044331] attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
[     1.044331] pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
[     1.044331] spkr0 at pcppi1: PC Speaker
[     1.044331] wsbell at spkr0 not configured
[     1.044331] midi0 at pcppi1: PC speaker
[     1.044331] sysbeep0 at pcppi1
[     1.044331] SIOR (PNP0C02) at acpi0 not configured
[     1.044331] RMSC (PNP0C02) at acpi0 not configured
[     1.044331] aibs0 at acpi0 (ASOC, ATK0110-16843024): ASUSTeK AI Booster
[     1.044331] FWH (INT0800) at acpi0 not configured
[     1.044331] FWHE (PNP0C02) at acpi0 not configured
[     1.044331] OMSC (PNP0C02) at acpi0 not configured
[     1.044331] pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
[     1.044331] PCIE (PNP0C02) at acpi0 not configured
[     1.044331] acpiwmi0 at acpi0 (WMI1, PNP0C14-MXM2): ACPI WMI Interface
[     1.044331] acpiwmibus at acpiwmi0 not configured
[     1.044331] RMEM (PNP0C01) at acpi0 not configured
[     1.044331] acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
[     1.044331] ACPI: Enabled 3 GPEs in block 00 to 3F
[     1.044331] attimer1: attached to pcppi1
[     1.044331] pckbd0 at pckbc1 (kbd slot)
[     1.044331] pckbc1: using irq 1 for kbd slot
[     1.044331] wskbd0 at pckbd0: console keyboard
[     1.044331] pci0 at mainbus0 bus 0: configuration mode 1
[     1.044331] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[     1.044331] pchb0 at pci0 dev 0 function 0: vendor 8086 product 3405 (rev. 0x13)
[     1.044331] ppb0 at pci0 dev 1 function 0: vendor 8086 product 3408 (rev. 0x13)
[     1.044331] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
[     1.044331] ppb0: link is x4 @ 2.5GT/s
[     1.044331] pci1 at ppb0 bus 1
[     1.044331] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] ppb1 at pci1 dev 0 function 0: vendor 1033 product 0125 (rev. 0x06)
[     1.044331] ppb1: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
[     1.044331] pci2 at ppb1 bus 3
[     1.044331] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] ppb2 at pci1 dev 0 function 1: vendor 1033 product 0125 (rev. 0x06)
[     1.044331] ppb2: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
[     1.044331] pci3 at ppb2 bus 2
[     1.044331] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] ppb3 at pci0 dev 3 function 0: vendor 8086 product 340a (rev. 0x13)
[     1.044331] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 5.0GT/s
[     1.044331] pci4 at ppb3 bus 4
[     1.044331] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] radeon0 at pci4 dev 0 function 0: vendor 1002 product 6818 (rev. 0x00)
[     1.044331] hdaudio0 at pci4 dev 0 function 1: HD Audio Controller
[     1.044331] hdaudio0: interrupting at msi0 vec 0
[     1.044331] hdafg0 at hdaudio0: vendor 1002 product aa01
[     1.044331] hdafg0: HDMI00 2ch: Digital Out [Jack]
[     1.044331] hdafg0: HDMI01 2ch: Digital Out [Jack]
[     1.044331] hdafg0: HDMI02 2ch: Digital Out [Jack]
[     1.044331] hdafg0: HDMI03 2ch: Digital Out [Jack]
[     1.044331] hdafg0: HDMI04 2ch: Digital Out [Jack]
[     1.044331] hdafg0: HDMI05 2ch: Digital Out [Jack]
[     1.044331] hdafg0: 2ch/0ch 32000Hz 44100Hz 48000Hz PCM16 AC3
[     1.044331] ppb4 at pci0 dev 7 function 0: vendor 8086 product 340e (rev. 0x13)
[     1.044331] ppb4: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 5.0GT/s
[     1.044331] pci5 at ppb4 bus 5
[     1.044331] pci5: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] vendor 8086 product 342e (interrupt system, generic 8259, revision 0x13) at pci0 dev 20 function 0 not configured
[     1.044331] vendor 8086 product 3422 (interrupt system, generic 8259, revision 0x13) at pci0 dev 20 function 1 not configured
[     1.044331] vendor 8086 product 3423 (interrupt system, generic 8259, revision 0x13) at pci0 dev 20 function 2 not configured
[     1.044331] vendor 8086 product 3438 (interrupt system, generic 8259, revision 0x13) at pci0 dev 20 function 3 not configured
[     1.044331] uhci0 at pci0 dev 26 function 0: vendor 8086 product 3a37 (rev. 0x00)
[     1.044331] uhci0: interrupting at ioapic0 pin 16
[     1.044331] usb0 at uhci0: USB revision 1.0
[     1.044331] uhci1 at pci0 dev 26 function 1: vendor 8086 product 3a38 (rev. 0x00)
[     1.044331] uhci1: interrupting at ioapic0 pin 21
[     1.044331] usb1 at uhci1: USB revision 1.0
[     1.044331] uhci2 at pci0 dev 26 function 2: vendor 8086 product 3a39 (rev. 0x00)
[     1.044331] uhci2: interrupting at ioapic0 pin 19
[     1.044331] usb2 at uhci2: USB revision 1.0
[     1.044331] ehci0 at pci0 dev 26 function 7: vendor 8086 product 3a3c (rev. 0x00)
[     1.044331] ehci0: interrupting at ioapic0 pin 18
[     1.044331] ehci0: EHCI version 1.0
[     1.044331] ehci0: 3 companion controllers, 2 ports each: uhci0 uhci1 uhci2
[     1.044331] usb3 at ehci0: USB revision 2.0
[     1.044331] hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
[     1.044331] hdaudio1: interrupting at msi1 vec 0
[     1.044331] hdafg1 at hdaudio1: vendor 11d4 product 989b
[     1.044331] hdafg1: DAC00 8ch: Speaker [Jack]
[     1.044331] hdafg1: ADC01 2ch: CD [Built-In], Line In [Jack], Mic In [Jack]
[     1.044331] hdafg1: DAC02 2ch: HP Out [Jack]
[     1.044331] hdafg1: DIG03 2ch: SPDIF Out [Jack]
[     1.044331] hdafg1: DIG04 2ch: Digital Out [Jack]
[     1.044331] hdafg1: 8ch/2ch 8000Hz 11025Hz 16000Hz 22050Hz 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
[     1.044331] audio0 at hdafg1: playback, capture, full duplex, independent
[     1.044331] audio0: slinear_le:16 8ch 48000Hz, blk 40ms for playback
[     1.044331] audio0: slinear_le:16 2ch 48000Hz, blk 40ms for recording
[     1.044331] spkr1 at audio0: PC Speaker (synthesized)
[     1.044331] wsbell at spkr1 not configured
[     1.044331] ppb5 at pci0 dev 28 function 0: vendor 8086 product 3a40 (rev. 0x00)
[     1.044331] ppb5: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
[     1.044331] pci6 at ppb5 bus 9
[     1.044331] pci6: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] athn0 at pci6 dev 0 function 0: Atheros AR9280
[     1.044331] athn0: rev 2 (2T2R), ROM rev 11, address 00:26:82:60:82:5f
[     1.044331] athn0: interrupting at ioapic0 pin 16
[     1.044331] athn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[     1.044331] athn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[     1.044331] athn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[     1.044331] ppb6 at pci0 dev 28 function 1: vendor 8086 product 3a42 (rev. 0x00)
[     1.044331] ppb6: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
[     1.044331] pci7 at ppb6 bus 8
[     1.044331] pci7: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] re0 at pci7 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x02)
[     1.044331] re0: interrupting at msix2 vec 0
[     1.044331] re0: Ethernet address 14:da:e9:20:0b:ce
[     1.044331] re0: using 256 tx descriptors
[     1.044331] rgephy0 at re0 phy 7: RTL8211B 1000BASE-T media interface
[     1.044331] rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[     1.044331] ppb7 at pci0 dev 28 function 2: vendor 8086 product 3a44 (rev. 0x00)
[     1.044331] ppb7: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
[     1.044331] pci8 at ppb7 bus 7
[     1.044331] pci8: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] re1 at pci8 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x02)
[     1.044331] re1: interrupting at msix3 vec 0
[     1.044331] re1: Ethernet address 14:da:e9:20:0c:40
[     1.044331] re1: using 256 tx descriptors
[     1.044331] rgephy1 at re1 phy 7: RTL8211B 1000BASE-T media interface
[     1.044331] rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[     1.044331] ppb8 at pci0 dev 28 function 3: vendor 8086 product 3a46 (rev. 0x00)
[     1.044331] ppb8: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
[     1.044331] pci9 at ppb8 bus 6
[     1.044331] pci9: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.044331] ahcisata0 at pci9 dev 0 function 0: vendor 11ab product 6121 (rev. 0xb2)
[     1.044331] ahcisata0: 64-bit DMA
[     1.044331] ahcisata0: ignoring broken port multiplier support
[     1.044331] ahcisata0: AHCI revision 1.0, 3 ports, 32 slots, CAP 0xca207f02<PSC,SSC,ISS=0x2=Gen2,SAL,SSS,SNCQ,S64A>
[     1.044331] ahcisata0: interrupting at msi4 vec 0
[     1.044331] atabus0 at ahcisata0 channel 0
[     1.044331] atabus1 at ahcisata0 channel 1
[     1.044331] atabus2 at ahcisata0 channel 2
[     1.044331] uhci3 at pci0 dev 29 function 0: vendor 8086 product 3a34 (rev. 0x00)
[     1.044331] uhci3: interrupting at ioapic0 pin 23
[     1.044331] usb4 at uhci3: USB revision 1.0
[     1.044331] uhci4 at pci0 dev 29 function 1: vendor 8086 product 3a35 (rev. 0x00)
[     1.044331] uhci4: interrupting at ioapic0 pin 19
[     1.044331] usb5 at uhci4: USB revision 1.0
[     1.044331] uhci5 at pci0 dev 29 function 2: vendor 8086 product 3a36 (rev. 0x00)
[     1.044331] uhci5: interrupting at ioapic0 pin 18
[     1.044331] usb6 at uhci5: USB revision 1.0
[     1.044331] ehci1 at pci0 dev 29 function 7: vendor 8086 product 3a3a (rev. 0x00)
[     1.044331] ehci1: interrupting at ioapic0 pin 23
[     1.044331] ehci1: EHCI version 1.0
[     1.044331] ehci1: 3 companion controllers, 2 ports each: uhci3 uhci4 uhci5
[     1.044331] usb7 at ehci1: USB revision 2.0
[     1.044331] ppb9 at pci0 dev 30 function 0: vendor 8086 product 244e (rev. 0x90)
[     1.044331] pci10 at ppb9 bus 10
[     1.044331] pci10: i/o space, memory space enabled
[     1.044331] fwohci0 at pci10 dev 4 function 0: vendor 11c1 product 5811 (rev. 0x70)
[     1.044331] fwohci0: interrupting at ioapic0 pin 19
[     1.044331] fwohci0: OHCI version 1.0 (ROM=1)
[     1.044331] fwohci0: No. of Isochronous channels is 8.
[     1.044331] fwohci0: EUI64 00:1e:8c:00:00:e5:18:a0
[     1.044331] fwohci0: Phy 1394a available S400, 2 ports.
[     1.044331] fwohci0: Link S400, max_rec 2048 bytes.
[     1.044331] ieee1394if0 at fwohci0: IEEE1394 bus
[     1.044331] fwip0 at ieee1394if0: IP over IEEE1394
[     1.044331] fwohci0: Initiate bus reset
[     1.044331] fwohci0: Clear PME# now
[     1.044331] ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 3a16 (rev. 0x00)
[     1.044331] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[     1.044331] ichlpcib0: 24-bit timer
[     1.044331] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[     1.044331] tco0: Min/Max interval 1/367 seconds
[     1.044331] piixide0 at pci0 dev 31 function 2: Intel 82801JI Serial ATA Controller (ICH10) (rev. 0x00)
[     1.044331] piixide0: bus-master DMA support present
[     1.044331] piixide0: primary channel configured to native-PCI mode
[     1.044331] piixide0: using ioapic0 pin 19 for native-PCI interrupt
[     1.044331] atabus3 at piixide0 channel 0
[     1.044331] piixide0: secondary channel configured to native-PCI mode
[     1.044331] atabus4 at piixide0 channel 1
[     1.044331] ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 3a30 (rev. 0x00)
[     1.044331] ichsmb0: interrupting at ioapic0 pin 18
[     1.044331] iic0 at ichsmb0: I2C bus
[     1.044331] piixide1 at pci0 dev 31 function 5: Intel 82801JI Serial ATA Controller (ICH10) (rev. 0x00)
[     1.044331] piixide1: bus-master DMA support present
[     1.044331] piixide1: primary channel wired to native-PCI mode
[     1.044331] piixide1: using ioapic0 pin 19 for native-PCI interrupt
[     1.044331] atabus5 at piixide1 channel 0
[     1.044331] piixide1: secondary channel wired to native-PCI mode
[     1.044331] atabus6 at piixide1 channel 1
[     1.044331] isa0 at ichlpcib0
[     1.044331] lpt0 at isa0 port 0x378-0x37b irq 7
[     1.044331] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
[     1.044331] acpicpu0 at cpu0: ACPI CPU
[     1.044331] acpicpu0: C1: HLT, lat   0 us, pow     0 mW
[     1.044331] acpicpu0: P0: FFH, lat  10 us, pow 143000 mW, 3201 MHz, turbo boost
[     1.044331] acpicpu0: P1: FFH, lat  10 us, pow 130000 mW, 3200 MHz
[     1.044331] acpicpu0: P2: FFH, lat  10 us, pow 114000 mW, 3067 MHz
[     1.044331] acpicpu0: P3: FFH, lat  10 us, pow 102000 mW, 2933 MHz
[     1.044331] acpicpu0: P4: FFH, lat  10 us, pow 92000 mW, 2800 MHz
[     1.044331] acpicpu0: P5: FFH, lat  10 us, pow 82000 mW, 2667 MHz
[     1.044331] acpicpu0: P6: FFH, lat  10 us, pow 74000 mW, 2533 MHz
[     1.044331] acpicpu0: P7: FFH, lat  10 us, pow 66000 mW, 2400 MHz
[     1.044331] acpicpu0: P8: FFH, lat  10 us, pow 57000 mW, 2267 MHz
[     1.044331] acpicpu0: P9: FFH, lat  10 us, pow 51000 mW, 2133 MHz
[     1.044331] acpicpu0: P10: FFH, lat  10 us, pow 46000 mW, 2000 MHz
[     1.044331] acpicpu0: P11: FFH, lat  10 us, pow 41000 mW, 1867 MHz
[     1.044331] acpicpu0: P12: FFH, lat  10 us, pow 37000 mW, 1733 MHz
[     1.044331] acpicpu0: P13: FFH, lat  10 us, pow 33000 mW, 1600 MHz
[     1.044331] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
[     1.044331] acpicpu1 at cpu1: ACPI CPU
[     1.044331] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
[     1.044331] acpicpu2 at cpu2: ACPI CPU
[     1.044331] coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=100
[     1.044331] acpicpu3 at cpu3: ACPI CPU
[     1.044331] coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=100
[     1.044331] acpicpu4 at cpu4: ACPI CPU
[     1.044331] acpicpu5 at cpu5: ACPI CPU
[     1.044331] acpicpu6 at cpu6: ACPI CPU
[     1.044331] acpicpu7 at cpu7: ACPI CPU
[     1.044331] fwohci0: BUS reset
[     1.044331] fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
[     1.044331] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
[     1.044331] ieee1394if0: bus manager 0
[     1.044331] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[     1.422808] autoconfiguration error: ERROR: 278 cycle TSC drift observed
[     1.422808] IPsec: Initialized Security Association Processing.
[     1.442820] uhub0 at usb0: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub0: 2 ports with 2 removable, self powered
[     1.442820] uhub1 at usb1: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub1: 2 ports with 2 removable, self powered
[     1.442820] uhub2 at usb2: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub2: 2 ports with 2 removable, self powered
[     1.442820] uhub3 at usb3: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[     1.442820] uhub3: 6 ports with 6 removable, self powered
[     1.442820] uhub4 at usb4: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub4: 2 ports with 2 removable, self powered
[     1.442820] uhub5 at usb5: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub5: 2 ports with 2 removable, self powered
[     1.442820] uhub6 at usb6: NetBSD (0000) UHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[     1.442820] uhub6: 2 ports with 2 removable, self powered
[     1.442820] uhub7 at usb7: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[     1.442820] uhub7: 6 ports with 6 removable, self powered
[     2.463676] delaying ask root by 5 seconds due to USB owner change.ehci1: handing over low speed device on port 3 to uhci4
[     2.523700] atapibus0 at atabus4: 2 targets
[     2.533708] cd0 at atapibus0 drive 0: <ATAPI   iHAS120   D, 3520015 2C8240503981, GL02> cdrom removable
[     2.533708] cd0: 32-bit data port
[     2.533708] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[     2.533708] wd0 at atabus4 drive 1
[     2.533708] wd0: <SAMSUNG HD501LJ>
[     2.533708] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[     2.533708] wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
[     2.563733] wd0: GPT GUID: 0ec9a630-50ff-43ec-93da-d682425cb193
[     2.573749] dk0 at wd0: "0485992e-c1b5-4344-93a4-e2b549689562", 926474221 blocks at 2048, type: ffs
[     2.573749] dk1 at wd0: "3f6c96e8-ac84-47af-bd90-9b8adb06d076", 50296847 blocks at 926476288, type: swap
[     2.573749] wd0: 32-bit data port
[     2.573749] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7, NCQ (32 tags)
[     2.573749] cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
[     2.573749] wd0(piixide0:1:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
[     2.833859] ehci1: handing over low speed device on port 4 to uhci4
[     3.694226] umass0 at uhub3 port 4 configuration 1 interface 0
[     3.694226] umass0: Generic (0x58f) Mass Storage Device (0x6362), rev 2.00/1.00, addr 2
[     3.694226] umass0: using SCSI over Bulk-Only
[     3.694226] scsibus0 at umass0: 2 targets, 4 luns per target
[     3.694226] sd0 at scsibus0 target 0 lun 0: <Generic, USB SD Reader, 1.00> disk removable
[     3.694226] sd0: drive offline
[     3.694226] sd1 at scsibus0 target 0 lun 1: <Generic, USB CF Reader, 1.01> disk removable
[     3.694226] sd1: drive offline
[     3.694226] sd2 at scsibus0 target 0 lun 2: <Generic, USB xD/SM Reader, 1.02> disk removable
[     3.704258] sd2: drive offline
[     3.704258] sd3 at scsibus0 target 0 lun 3: <Generic, USB MS Reader, 1.03> disk removable
[     3.704258] sd3: drive offline
[     4.474599] uhidev0 at uhub5 port 1 configuration 1 interface 0
[     4.474599] uhidev0: Microsoft (0x45e) Microsoft Basic Optical Mouse v2.0 (0xcb), rev 1.10/1.99, addr 2, iclass 3/1
[     4.484607] ums0 at uhidev0: 3 buttons and Z dir
[     4.484607] wsmouse0 at ums0 mux 0
[     5.224915] umass1 at uhub3 port 6 configuration 1 interface 0
[     5.224915] umass1: SanDisk (0x781) ExtremePro (0x5588), rev 2.10/0.10, addr 3
[     5.224915] umass1: using SCSI over Bulk-Only
[     5.224915] scsibus1 at umass1: 2 targets, 1 lun per target
[     5.224915] sd4 at scsibus1 target 0 lun 0: <SanDisk, ExtremePro, 0001> disk removable
[     5.555061] sd4(umass1:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
[     5.555061] SENSE KEY:  Not Ready
[     5.555061] ASC/ASCQ:  Logical Unit Is In Process Of Becoming Ready
[     5.555061] sd4: drive offline
[     5.555061] sd4: fabricating a geometry
[     6.265365] uhidev1 at uhub5 port 2 configuration 1 interface 0
[     6.265365] uhidev1: vendor 046a (0x46a) product 0023 (0x23), rev 2.00/2.20, addr 3, iclass 3/1
[     6.295381] ukbd0 at uhidev1: 8 Variable keys, 6 Array codes
[     6.705551] wskbd1 at ukbd0 mux 1
[     6.705551] uhidev2 at uhub5 port 2 configuration 1 interface 1
[     6.705551] uhidev2: vendor 046a (0x46a) product 0023 (0x23), rev 2.00/2.20, addr 3, iclass 3/0
[     6.735568] uhidev2: 2 report ids
[     6.735568] uhid0 at uhidev2 reportid 1: input=2, output=0, feature=0
[     6.735568] uhid1 at uhidev2 reportid 2: input=1, output=0, feature=0
[     7.535937] WARNING: 1 error while detecting hardware; check system log.
[     7.535937] boot device: wd0
[     7.535937] root on dk0 dumps on dk1
[     7.565961] root file system type: ffs
[     7.565961] kern.module.path=/stand/amd64/8.99.45/modules
[     7.565961] kern info: [drm] initializing kernel modesetting (PITCAIRN 0x1002:0x6818 0x1682:0x3252).
[     7.565961] kern info: [drm] register mmio base: 0xfb980000
[     7.565961] kern info: [drm] register mmio size: 262144
[     8.256252] kern info: ATOM BIOS: C40102
[     8.256252] radeon0: info: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used)
[     8.256252] radeon0: info: GTT: 2048M 0x0000000080000000 - 0x00000000FFFFFFFF
[     8.266251] kern info: [drm] Detected VRAM RAM=800M, BAR=256M
[     8.266251] kern info: [drm] RAM width 256bits DDR
[     8.266251] Zone  kernel: Available graphics memory: 4069846 kiB
[     8.266251] Zone   dma32: Available graphics memory: 2097152 kiB
[     8.266251] kern info: [drm] radeon: 2048M of VRAM memory ready
[     8.266251] kern info: [drm] radeon: 2048M of GTT memory ready.
[     8.266251] kern info: [drm] Loading pitcairn Microcode
[     8.366298] kern info: [drm] radeon/PITCAIRN_mc2.bin: 31100 bytes
[     8.366298] kern info: [drm] Internal thermal controller with fan control
[     8.386333] kern info: [drm] radeon: dpm initialized
[     8.386333] radeon0: autoconfiguration error: error: radeon_vce: Can't load firmware "radeon/TAHITI_vce.bin"
[     8.386333] kern info: [drm] GART: num cpu pages 524288, num gpu pages 524288
[     8.416369] kern info: [drm] PCIE GART of 2048M enabled (table at 0x0000000000277000).
[     8.416369] radeon0: info: WB enabled
[     8.416369] radeon0: info: fence driver on ring 0 use gpu addr 0x0000000080000c00 and cpu addr 0x0xffff9fbb6eafbc00
[     8.416369] radeon0: info: fence driver on ring 1 use gpu addr 0x0000000080000c04 and cpu addr 0x0xffff9fbb6eafbc04
[     8.416369] radeon0: info: fence driver on ring 2 use gpu addr 0x0000000080000c08 and cpu addr 0x0xffff9fbb6eafbc08
[     8.416369] radeon0: info: fence driver on ring 3 use gpu addr 0x0000000080000c0c and cpu addr 0x0xffff9fbb6eafbc0c
[     8.416369] radeon0: info: fence driver on ring 4 use gpu addr 0x0000000080000c10 and cpu addr 0x0xffff9fbb6eafbc10
[     8.416369] radeon0: info: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0x0xffffc100f7485a18
[     8.416369] radeon0: autoconfiguration error: error: VCE init error (-22).
[     8.416369] kern info: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[     8.416369] kern info: [drm] Driver supports precise vblank timestamp query.
[     8.416369] radeon0: info: radeon: MSI limited to 32-bit
[     8.416369] radeon0: interrupting at ioapic1 pin 0 (radeon0)
[     8.416369] kern info: [drm] radeon: irq initialized.
[     8.606446] kern info: [drm] ring test on 0 succeeded in 3 usecs
[     8.606446] kern info: [drm] ring test on 1 succeeded in 1 usecs
[     8.606446] kern info: [drm] ring test on 2 succeeded in 1 usecs
[     8.606446] kern info: [drm] ring test on 3 succeeded in 6 usecs
[     8.606446] kern info: [drm] ring test on 4 succeeded in 6 usecs
[     8.776514] kern info: [drm] ring test on 5 succeeded in 2 usecs
[     8.776514] kern info: [drm] UVD initialized successfully.
[     8.776514] kern info: [drm] ib test on ring 0 succeeded in 0 usecs
[     8.776514] kern info: [drm] ib test on ring 1 succeeded in 0 usecs
[     8.776514] kern info: [drm] ib test on ring 2 succeeded in 0 usecs
[     8.786519] kern info: [drm] ib test on ring 3 succeeded in 0 usecs
[     8.786519] kern info: [drm] ib test on ring 4 succeeded in 0 usecs
[     9.426789] kern info: [drm] ib test on ring 5 succeeded
[     9.426789] kern info: [drm] Radeon Display Connectors
[     9.426789] kern info: [drm] Connector 0:
[     9.426789] kern info: [drm]   DP-1
[     9.426789] kern info: [drm]   HPD4
[     9.426789] kern info: [drm]   DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[     9.426789] kern info: [drm]   Encoders:
[     9.426789] kern info: [drm]     DFP1: INTERNAL_UNIPHY2
[     9.426789] kern info: [drm] Connector 1:
[     9.426789] kern info: [drm]   DP-2
[     9.426789] kern info: [drm]   HPD5
[     9.426789] kern info: [drm]   DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[     9.426789] kern info: [drm]   Encoders:
[     9.426789] kern info: [drm]     DFP2: INTERNAL_UNIPHY2
[     9.426789] kern info: [drm] Connector 2:
[     9.426789] kern info: [drm]   HDMI-A-1
[     9.426789] kern info: [drm]   HPD1
[     9.426789] kern info: [drm]   DDC: 0x6550 0x6550 0x6554 0x6554 0x6558 0x6558 0x655c 0x655c
[     9.426789] kern info: [drm]   Encoders:
[     9.426789] kern info: [drm]     DFP3: INTERNAL_UNIPHY1
[     9.426789] kern info: [drm] Connector 3:
[     9.426789] kern info: [drm]   DVI-I-1
[     9.426789] kern info: [drm]   HPD6
[     9.426789] kern info: [drm]   DDC: 0x6580 0x6580 0x6584 0x6584 0x6588 0x6588 0x658c 0x658c
[     9.426789] kern info: [drm]   Encoders:
[     9.426789] kern info: [drm]     DFP4: INTERNAL_UNIPHY
[     9.426789] kern info: [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[     9.426789] kern info: [drm] Connector 4:
[     9.426789] kern info: [drm]   DVI-D-1
[     9.436801] kern info: [drm]   HPD3
[     9.436801] kern info: [drm]   DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
[     9.436801] kern info: [drm]   Encoders:
[     9.436801] kern info: [drm]     DFP5: INTERNAL_UNIPHY1
[     9.496819] radeondrmkmsfb0 at radeon0
[     9.496819] radeondrmkmsfb0: framebuffer at 0xffffc100f7ed5000, size 3840x2160, depth 32, stride 15360
[     9.666887] kern error: [drm:(/usr/src/sys/external/bsd/drm2/dist/drm/radeon/radeon_si_dpm.c:6626)si_dpm_set_power_state] *ERROR* si_restrict_performance_levels_before_switch failed
[     9.766928] wsdisplay0 at radeondrmkmsfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
[     9.847158] wsmux1: connecting to wsdisplay0
[     9.847158] wskbd1: connecting to wsdisplay0
[    28.104865] sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
[    28.104865] SENSE KEY:  Not Ready
[    28.104865] COMMAND INFO:  11162944 (0xaa5540)
[    28.104865] ASC/ASCQ:  Medium Not Present
[    31.786389] aibs0: warning under limit on 'CHASSIS1 FAN Speed'
[    32.086523] aibs0: warning under limit on 'CHASSIS2 FAN Speed'
[    32.286616] aibs0: warning under limit on 'CHASSIS3 FAN Speed'
[    32.436689] aibs0: warning under limit on 'POWER FAN Speed'
>Fix:
Yes, please.

>Unformatted: