Hi all,

i have some trouble with a realtek-card on my netbsd-box
My box had 2 DE450TA(10mbit)cards.Both working w/o problems.
A few days ago,i=B4ve got another hub(100mbit only;12-port;allied
telesyn).
Because of the 100mbit-only i replaced de1 with an realtek 8139c-based =

10/100mbit card to connect it to my new hub.
But it doesnt work.
I removed the /etc/ifconfig.de1 and
wrote an ifconfig.rtk0 and saved it in /etc :

bash-2.03# cat ifconfig.rtk0
inet 192.168.2.254 netmask 0xffffff00 =


when i try to get it up,i get the following
error message:

bash-2.03# ifconfig rtk0 up
ifconfig: SIOCGIFFLAGS rtk0: Device not configured

here is the dmesg output:

bash-2.03# dmesg
NetBSD 1.4.1 (GENERIC) #1: Tue Aug 10 00:03:09 MEST 1999
    fvdl@struis:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: family 5 model 2 step 5
cpu0: Intel Pentium (P54C) (586-class)
real mem  =3D 66715648
avail mem =3D 58343424
using 840 buffers containing 3440640 bytes of memory
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o enabled, memory enabled
pchb0 at pci0 dev 0 function 0
pchb0: Silicon Integrated System 85C501 (rev. 0x00)
pcib0 at pci0 dev 1 function 0
pcib0: Silicon Integrated System 85C503 or 5597/5598 ISA bridge (rev.
0x00)
vga1 at pci0 dev 13 function 0: ATI Technologies Mach64 CT (rev. 0x0a)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
de0 at pci0 dev 15 function 0
de0: interrupting at irq 10
de0: DEC DE450-TA 21041 [10Mb/s] pass 1.1
de0: address 00:00:f8:00:ef:c6
Realtek Semiconductor 8139 10/100 Ethernet (ethernet network, revision
0x10) at pci0 dev 17 function 0 not configured
ahc1 at pci0 dev 19 function 0
ahc1: interrupting at irq 9
ahc1: aic7870 Single Channel, SCSI Id=3D7, 16 SCBs
scsibus0 at ahc1 channel 0: 8 targets, 8 luns per target
ahc1: target 0 synchronous at 10.0MHz, offset =3D 0xf
sd0 at scsibus0 targ 0 lun 0: <IBM, DCHS04U, 6464> SCSI2 0/direct fixed
sd0: 4303MB, 6077 cyl, 9 head, 161 sec, 512 bytes/sect x 8813870 sectors
ahc1: target 1 synchronous at 10.0MHz, offset =3D 0xf
sd1 at scsibus0 targ 1 lun 0: <IBM, DCHS04U, 6464> SCSI2 0/direct fixed
sd1: 4303MB, 6077 cyl, 9 head, 161 sec, 512 bytes/sect x 8813870 sectors
cd0 at scsibus0 targ 5 lun 0: <SANYO, CRD-254S, 1.04> SCSI2 5/cdrom
removable
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask 240 netmask 640 ttymask 6c2
de0: enabling 10baseT port
wscons: wskbd0 glued to wsdisplay0 (console)
boot device: sd0
root on sd0a dumps on sd0b
WARNING: NVRAM century is 20 but RTC year is 1994
WARNING: clock time much less than file system time
WARNING: using file system time
WARNING: CHECK AND RESET THE DATE!
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

what does "device not configured" mean?
is there no realtek support in the GENERIC installation kernel?
i haven=B4t tried netbsd-1.5,is there realtek support in GENERIC?

regards

Frank