Re: NetBSD hardware support for Gigabyte GA-EP45-UD3R, Intel Q9550S, Gigabyte GV-R455D3-512I?

[uhel%gmx.net@localhost]

On Fri, 25 Sep 2009 21:18:49 +0200 (CEST)
"Bernhard Riedel" <bernhard%netmuc.net@localhost> wrote:

> Hello,
> 
> as my trusty old Asus TUSL2-C is slowly dying, I have to think about a
>  new peecee.
> 
> A friend with good hardware experience (but only with Linux and Windogs)
>  recommended a few components, and I would like to hear if anybody here
>  had good/bad/ugly experiences trying to run NetBSD with identical or
>  similar hardware.
> 
> Motherboard: 
> http://www.gigabyte.de/Products/Motherboard/Products_Overview.aspx?ProductID=4376
>              Gigabyte GA-EP45-UD3R
>              Socket 775, Intel P45 Chipset, ICH10R
>              audio: Realtek ALC889A codec
>              LAN: Realtek 8111C
>              ATA via ICH10R: 6*SATA 3Gb/s
>              ATA via "GIGABYTE SATA2 chip": 1*PATA, 2*SATA 3Gb/s
>              FDC: iTE IT8718
>              IEEE 1394a: T.I. TSB43AB23
> 
> CPU:         http://processorfinder.intel.com/details.aspx?sSpec=SLGAE
>              Intel Q9550S Socket 775
> 
> VGA:         
> http://www.gigabyte.de/Products/VGA/Products_Overview.aspx?ProductID=3664
>              Gigabyte GV-R455D3-512I
>              ATI Radeon HD 4550 chipset
>              512 MB DDR III
>              VGA+DVI+HDMI
>              passively cooled
> 
> Cheers, Bernhard.

Hi,
attached is an dmesg of an GA-EP45-DS3 from a Jibbed Live CD. It has an
core 2 duo and an asus EAH3450  videocard.

HTH

regards uli


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004,
2005, 2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0.1 (JIBBED5) #0: Wed Aug 26 00:49:49 CEST 2009
        zafer%pembe.aydogan.net@localhost:/root/livecd/work/JIBBED5
total memory = 3326 MB
avail memory = 3258 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Gigabyte Technology Co., Ltd. EP45-DS3 ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2533MHz, id 0x10676
cpu0: Enhanced SpeedStep (1180 mV) 800 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 7300 5700 4000
2300 700 cpu1 at mainbus0 apid 1: Intel 686-class, 2533MHz, id 0x10676
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <GBT   ,GBTUACPI,42302e31>, AslId <GBTU,01010101>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43
HPET (PNP0103) at acpi0 not configured
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
UAR1 (PNP0501) at acpi0 not configured
LPT1 (PNP0400) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
FWH (INT0800) at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: unable to establish interrupt for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2e20 (rev. 0x02)
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2e21 (rev. 0x02)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: vendor 0x1002 product 0x95c5 (rev. 0x00)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using
wskbd0 wsmux1: connecting to wsdisplay0
drm at vga1 not configured
azalia0 at pci1 dev 0 function 1: Generic High Definition Audio
Controller azalia0: interrupting at ioapic0 pin 17
azalia0: host: 0x1002/0xaa28 (rev. 0), HDA rev. 1.0
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3a37 (rev.
0x00) uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x3a38 (rev.
0x00) uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x3a39 (rev.
0x00) uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x3a3c (rev.
0x00) ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
azalia1 at pci0 dev 27 function 0: Generic High Definition Audio
Controller azalia1: interrupting at ioapic0 pin 22
azalia1: host: 0x8086/0x3a3e (rev. 0), HDA rev. 1.0
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x3a40 (rev. 0x00)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 3: vendor 0x8086 product 0x3a46 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
jmide0 at pci3 dev 0 function 0: vendor 0x197b product 0x2368
jmide0: 1 PATA port
jmide0: interrupting at ioapic0 pin 19
jmide0: PCI IDE interface used
jmide0: bus-master DMA support present
jmide0: primary channel wired to native-PCI mode
jmide0: primary channel is PATA
atabus0 at jmide0 channel 0
jmide0: secondary channel wired to native-PCI mode
jmide0: secondary channel is unused
ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x3a48 (rev. 0x00)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci4 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet
(rev. 0x02) re0: interrupting at ioapic0 pin 16
re0: Ethernet address 00:1f:d0:5c:2c:b9
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface,
rev. 2 rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT, 1000baseT-FDX, auto ppb4 at pci0 dev 28 function 5: vendor
0x8086 product 0x3a4a (rev. 0x00) pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
re1 at pci5 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet
(rev. 0x02) re1: interrupting at ioapic0 pin 17
re1: Ethernet address 00:1f:d0:80:18:c1
re1: using 256 tx descriptors
rgephy1 at re1 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface,
rev. 2 rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT, 1000baseT-FDX, auto uhci3 at pci0 dev 29 function 0: vendor
0x8086 product 0x3a34 (rev. 0x00) uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x3a35 (rev.
0x00) uhci4: interrupting at ioapic0 pin 19
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x3a36 (rev.
0x00) uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x3a3a (rev.
0x00) ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x90)
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled
fwohci0 at pci6 dev 7 function 0: vendor 0x104c product 0x8024 (rev.
0x00) fwohci0: interrupting at ioapic0 pin 23
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:72:f3:78:00:00:1f:d0
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x3a18 (rev. 0x00)
piixide0 at pci0 dev 31 function 2
piixide0: Intel ICH10 Serial ATA 2 Controller 4x2 (rev. 0x00)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus1 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus2 at piixide0 channel 1
vendor 0x8086 product 0x3a30 (SMBus serial bus) at pci0 dev 31 function
3 not configured piixide1 at pci0 dev 31 function 5
piixide1: Intel ICH10 Serial ATA 2 Controller 2x2 (rev. 0x00)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus3 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus4 at piixide1 channel 1
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: ATI R600 HDMI (rev. 0.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
azalia1: codec[2]: Realtek ALC885 (rev. 1.1), HDA rev. 1.0
audio1 at azalia1: full duplex, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00,
addr 1 uhub3: 6 ports with 6 removable, self powered
atapibus0 at atabus0: 2 targets
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1 uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00,
addr 1 uhub7: 6 ports with 6 removable, self powered
cd0 at atapibus0 drive 0: <TSSTcorpDVD-ROM SH-D162C, , TS04> cdrom
removable cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
IPsec: Initialized Security Association Processing.
cd1 at atapibus0 drive 1: <Hewlett-Packard CD-Writer Plus 9700, , 1.0N>
cdrom removable cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 1
cd0(jmide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using
DMA) cd1(jmide0:0:1): using PIO mode 4, Ultra-DMA mode 1 (using DMA)
uhidev0 at uhub2 port 1 configuration 1 interface 0
uhidev0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev
1.10/3.00, addr 2, iclass 3/1 ums0 at uhidev0: 5 buttons and Z dir.
wsmouse1 at ums0 mux 0
wd0 at atabus1 drive 0: <SAMSUNG HD322HJ>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620178 cyl, 16 head, 63 sec, 512 bytes/sect x 625140335
sectors wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133)
(using DMA) Kernelized RAIDframe activated
boot device: cd0
root on cd0a
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)
pckbport: command timeout
pms_enable: command error 35
pckbport: command timeout
pckbport: command timeout
pms_disable: command error
pckbport: command timeout
pms_enable: command error 35
pckbport: command timeout
pms_disable: command error