Drives not showing up when plugged into Intel 82801GBM ICH7 SATA controller

[mark hellewell <mark.hellewell%gmail.com@localhost>]

Hi,

I have installed 5.1 to the flash drive of my NAS?it's only 128MiB so base
install was pretty tight, but it's on there!?and everything seems to be
great, apart from one thing: none of the drives I'm plugging in to the Intel
82801GBM ICH7 SATA controller even show up in the dmesg (which is reproduced
below).  I've been through all the BIOS options available to me and nothing
makes a difference to what I'm seeing.  There doesn't seem to be any
RAID-specific config options in the BIOS.  Am I missing something?

Cheers,
Mark

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002,
2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (GENERIC) #0: Sun Nov  7 14:39:56 UTC 2010
        builds%b6.netbsd.org@localhost:
/home/builds/ab/netbsd-5-1-RELEASE/i386/201011061943Z
-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 1022 MB
avail memory = 992 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
QNAP TS-509-Q025MB (V1.00)
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (Intel    Lakeport    )
cpu0 at mainbus0 apid 0: Intel 686-class, 1596MHz, id 0x10661
mpbios: bus 0 is type PCI
mpbios: bus 1 is type PCI
mpbios: bus 2 is type PCI
mpbios: bus 3 is type PCI
mpbios: bus 4 is type PCI
mpbios: bus 5 is type PCI
mpbios: bus 6 is type ISA
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2770 (rev. 0x02)
agp0 at pchb0: detected 764k stolen memory
agp0: aperture at 0xe0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2772 (rev. 0x02)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x11ab product 0x7042 (SCSI mass storage, revision 0x02) at pci1 dev
0 func
tion 0 not configured
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x01)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x11ab product 0x7042 (SCSI mass storage, revision 0x02) at pci2 dev
0 func
tion 0 not configured
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x01)
pci3 at ppb2 bus 3
pci3: memory space enabled, rd/line, wr/inv ok
bge0 at pci3 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
bge0: interrupting at ioapic0 pin 18
bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:08:9b:8c:d9:04
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX,
 auto
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x01)
pci4 at ppb3 bus 4
pci4: memory space enabled, rd/line, wr/inv ok
bge1 at pci4 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
bge1: interrupting at ioapic0 pin 19
bge1: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:08:9b:8c:d9:05
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX,
 auto
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x01)
uhci3: interrupting at ioapic0 pin 16
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
ehci0: interrupting at ioapic0 pin 23
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
pci5 at ppb4 bus 5
pci5: no spaces enabled!
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
piixide1 at pci0 dev 31 function 2
piixide1: Intel 82801GB/GR Serial ATA/Raid Controller (ICH7) (rev. 0x01)
piixide1: bus-master DMA support present
piixide1: primary channel configured to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus1 at piixide1 channel 0
piixide1: secondary channel configured to native-PCI mode
atabus2 at piixide1 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: vendor 0x062a USB-compliant keyboard, rev 1.10/1.00, addr 2, iclass
3/1
ukbd0 at uhidev0
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 1
uhidev1: vendor 0x062a USB-compliant keyboard, rev 1.10/1.00, addr 2, iclass
3/1
uhidev1: 6 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 4: input=1, output=0, feature=0
ums0 at uhidev1 reportid 5: 0 buttons and Z dir
wsmouse0 at ums0 mux 0
uhid3 at uhidev1 reportid 6: input=3, output=0, feature=0
wd0 at atabus0 drive 0: < 128MB ATA Flash Disk>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 122 MB, 977 cyl, 8 head, 32 sec, 512 bytes/sect x 250112 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
wd0(piixide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)