Re: dell poweredge 1850 and interrupt re-mapping (disks timeout)

To: netbsd-users%netbsd.org@localhost
Subject: Re: dell poweredge 1850 and interrupt re-mapping (disks timeout)
From: john refling <netbsdrat%gmail.com@localhost>
Date: Mon, 19 Dec 2011 16:44:02 -0800
>In article
><CAB3JEf8T1kH_Aw_uzO-BqiEDE14JBnRsiypwsZNeCTqPhmbosA%mail.gmail.com@localhos
t
>,
john refling <netbsdrat%gmail.com@localhost> wrote:
>>I have a Dell poweredge 1850 and have tried installing adaptec 29160 /
>>39160 scsi cards.
>>
>>The scsi devices always time out. A freebsd post a few years ago points to
>>the same problem I have on NetBSD 5.1:
>>
>>*ahc1: Timedout SCB already complete. Interrupts** may not be functioning.
>>***
>>here:
>>http://lists.freebsd.org/pipermail/freebsd-scsi/2003-September/000566.html
>>
>>I assume that this is a similar issue, namely with the Dell BIOS being
>>broken and reporting interrupts incorrectly, and then kernel not getting
>>correct interrupt.
>>
>
>Can you compile a kernel with PCIBIOSVERBOSE, PCIVERBOSE, PCI_INTR_FIXUP
>and send us the dmesg?
>
>christos

OK.  Below is the broken dmesg.  Had to capture via the serial console
consdev=com0
since machine never booted far enough the save the dmesg in a normal way.

Note that I had to install by booting the install cd with NO ACPI support.
 Then the installed
system would boot up (but only when using NO ACPI support there too).  Have
that dmesg
listing below too.

[this took forever since I was originally installing on a machine without
these problems
and moving the disk to the dell 1850 machine.  somehow the com0 bootblocks
(needed
to capture the dmesg) didn't work using this method].  Got the first few
lines, then nothing.

The 3rd dmesg below is output from a freebsd boot on the same machine.

It is odd that the adaptec scsi board comes up as ahc1 on netbsd, and ahc0,
in freebsd.

John Refling



====================== netbsd dmesg ==========================

options PCIBIOSVERBOSE
options PCIVERBOSE
options PCI_INTR_FIXUP

boot normally
post consdev=com0:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.19 16:09:28
=~=~=~=~=~=~=~=~=~=~=~=

>> NetBSD/x86 BIOS Boot, Revision 5.2 (from NetBSD 5.1)
>> Memory: 638/3144448 k
> boot netbsd.pciverbose
booting hd0a:netbsd.pciverbose
|/-\|/-10190280\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-+518916\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-+618576
\|
[521216/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+508034/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|]=0xbca4bc
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 5.1 (PCIVERBOSE) #0: Mon Dec 19 06:17:20 PST 2011
root@q04:/usr/obj/sys/arch/i386/compile/PCIVERBOSE
total memory = 3071 MB
avail memory = 3006 MB
Dell Computer Corporation PowerEdge 1850
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2992MHz, id 0xf43
cpu1 at mainbus0 apid 6: Intel 686-class, 2992MHz, id 0xf43
cpu2 at mainbus0 apid 1: Intel 686-class, 2992MHz, id 0xf43
cpu3 at mainbus0 apid 7: Intel 686-class, 2992MHz, id 0xf43
ioapic0 at mainbus0 apid 8
ioapic1 at mainbus0 apid 9
ioapic2 at mainbus0 apid 10
acpi0 at mainbus0: Intel ACPICA 20080321
npx1 at acpi0 (FPU, PNP0C04): io 0xf0-0xff irq 13
pcppi1 at acpi0 (SPK, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x5f irq 0
FDC (PNP0700) at acpi0 not configured
pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOU, PNP0F13) (aux port): irq 12
COMA (PNP0501) at acpi0 not configured
NIPM (IPI0001) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103-0): mem 0xfed00000-0xfed003ff
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0
pchb0: Intel E7525 Memory Controller Hub (rev. 0x09)
ppb0 at pci0 dev 2 function 0: Intel E7525 PCI Express Port A (rev. 0x09)
pci1 at ppb0 bus 1
ppb1 at pci1 dev 0 function 0: Intel product 0x0330 (rev. 0x06)
ppb1: disabling notification events
pci2 at ppb1 bus 2
ahc1 at pci2 dev 12 function 0: Adaptec 29160 Ultra160 SCSI adapter
ahc1: interrupting at ioapic0 pin 16
sleep(10)
ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ppb2 at pci1 dev 0 function 2: Intel product 0x0332 (rev. 0x06)
ppb2: disabling notification events
pci3 at ppb2 bus 3
ppb3 at pci0 dev 4 function 0: Intel E7525 PCI Express Port B (rev. 0x09)
pci4 at ppb3 bus 4
ppb4 at pci0 dev 5 function 0: Intel product 0x3598 (rev. 0x09)
pci5 at ppb4 bus 5
ppb5 at pci5 dev 0 function 0: Intel 6700PXH PCI Express-to-PCI Bridge #0
(rev. 0x09)
ppb5: disabling notification events
pci6 at ppb5 bus 6
wm0 at pci6 dev 7 function 0: Intel i82541GI 1000BASE-T Ethernet, rev. 5
wm0: interrupting at ioapic2 pin 0
wm0: Ethernet address 00:11:43:e8:01:8d
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb6 at pci5 dev 0 function 2: Intel 6700PXH PCI Express-to-PCI Bridge #1
(rev. 0x09)
ppb6: disabling notification events
pci7 at ppb6 bus 7
wm1 at pci7 dev 8 function 0: Intel i82541GI 1000BASE-T Ethernet, rev. 5
wm1: interrupting at ioapic2 pin 1
wm1: Ethernet address 00:11:43:e8:01:8e
igphy1 at wm1 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb7 at pci0 dev 6 function 0: Intel product 0x3599 (rev. 0x09)
pci8 at ppb7 bus 8
uhci0 at pci0 dev 29 function 0: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 29 function 7: Intel 82801EB/ER USB EHCI Controller (rev.
0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
ppb8 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xc2)
pci9 at ppb8 bus 9
vga1 at pci9 dev 13 function 0: ATI Technologies Radeon 7000/VE QY (rev.
0x00)
wsdisplay0 at vga1 kbdmux 1
drm at vga1 not configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: Intel 82801EB LPC Interface Bridge (rev. 0x02)
ichlpcib0: 24-bit timer
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801EB IDE Controller (ICH5) (rev. 0x02)
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
scsibus0: waiting 2 seconds for devices to settle...
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uhub0 at usb0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2 at usb2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3 at usb3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-STCD-RW/DVD-ROM GCC-4241N, , A101> cdrom
removable
uhub4 at uhub3 port 3: vendor 0x413c product 0xa001, class 9/0, rev
2.00/0.00, addr 2
uhub4: multiple transaction translators

ahc1: Timedout SCB already complete. Interrupts may not be functioning.
ahc1:SCB 0xe - timed out
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
ahc1: Dumping Card State in Message-out phase, at SEQADDR 0x173
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xe4, ARG_2 = 0x3
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x4] SCSISIGI[0xb6] ERROR[0x0] SCSIBUSL[0x1]
LASTPHASE[0xa0] SCSISEQ[0x12] SBLKCTL[0xa] SCSIRATE[0x0]
SEQCTL[0x10] SEQ_FLAGS[0x40] SSTAT0[0x2] SSTAT1[0x1]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x88] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0xe9 0x0 0x0 0x180
SCB count = 16
Kernel NEXTQSCB = 15
Card NEXTQSCB = 15
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x40]
SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0xe]
1 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
14 SCB_CONTROL[0x40]
SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Untagged Q(1): 14

<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
sg[0] - Addr 0x45a1c4a : Length 36
ahc1:BDR message in message buffer
ahc1:SCB 0xe - timed out
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
ahc1: Dumping Card State in Message-out phase, at SEQADDR 0x173
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xe4, ARG_2 = 0x3
HCNT = 0x0 SCBPTR = 0x0
SCSIPHASE[0x4] SCSISIGI[0xb6] ERROR[0x0] SCSIBUSL[0x2]
LASTPHASE[0xa0] SCSISEQ[0x12] SBLKCTL[0xa] SCSIRATE[0x0]
SEQCTL[0x10] SEQ_FLAGS[0x40] SSTAT0[0x2] SSTAT1[0x1]
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xac]
SXFRCTL0[0x88] DFCNTRL[0x0] DFSTATUS[0x89]
STACK: 0xe9 0x0 0x0 0x180
SCB count = 16
Kernel NEXTQSCB = 15
Card NEXTQSCB = 15
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0x40]
SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0xe]
1 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
16 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
17 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
18 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
19 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
20 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
21 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
22 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
23 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
24 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
25 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
26 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
27 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
28 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
29 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
30 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
31 SCB_CONTROL[0x0]
SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
14 SCB_CONTROL[0x40]
SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Untagged Q(1): 14

<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
sg[0] - Addr 0x45a1c4a : Length 36
probe(ahc1:0:1:0): ahc1: no longer in timeout, status = 0
ahc1: Issued Channel A Bus Reset. 1 SCBs aborted


====================== netbsd dmesg ==========================

options PCIBIOSVERBOSE
options PCIVERBOSE
options PCI_INTR_FIXUP

boot option 3 (disable ACPI support) [the only way to get it to boot
successfully]

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 5.1 (PCIVERBOSE) #0: Mon Dec 19 06:17:20 PST 2011
root@q04:/usr/obj/sys/arch/i386/compile/PCIVERBOSE
total memory = 3071 MB
avail memory = 3006 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Computer Corporation PowerEdge 1850
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (DELL PE 016C )
cpu0 at mainbus0 apid 0: Intel 686-class, 2992MHz, id 0xf43
cpu1 at mainbus0 apid 6: Intel 686-class, 2992MHz, id 0xf43
mpbios: bus 0 is type PCI
mpbios: bus 1 is type PCI
mpbios: bus 2 is type PCI
mpbios: bus 3 is type PCI
mpbios: bus 4 is type PCI
mpbios: bus 5 is type PCI
mpbios: bus 6 is type PCI
mpbios: bus 7 is type PCI
mpbios: bus 8 is type PCI
mpbios: bus 9 is type PCI
mpbios: bus 10 is type ISA
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0 apid 9: pa 0xfec80000, version 20, 24 pins
ioapic2 at mainbus0 apid 10: pa 0xfec83000, version 20, 24 pins
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel E7525 Memory Controller Hub (rev. 0x09)
ppb0 at pci0 dev 2 function 0: Intel E7525 PCI Express Port A (rev. 0x09)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci1 dev 0 function 0: Intel product 0x0330 (rev. 0x06)
ppb1: disabling notification events
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ahc1 at pci2 dev 12 function 0: Adaptec 29160 Ultra160 SCSI adapter
ahc1: interrupting at ioapic1 pin 7
sleep(10)
ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ppb2 at pci1 dev 0 function 2: Intel product 0x0332 (rev. 0x06)
ppb2: disabling notification events
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 4 function 0: Intel E7525 PCI Express Port B (rev. 0x09)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 5 function 0: Intel product 0x3598 (rev. 0x09)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
ppb5 at pci5 dev 0 function 0: Intel 6700PXH PCI Express-to-PCI Bridge #0
(rev. 0x09)
ppb5: disabling notification events
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci6 dev 7 function 0: Intel i82541GI 1000BASE-T Ethernet, rev. 5
wm0: interrupting at ioapic2 pin 0
wm0: 32-bit 66MHz PCI bus
wm0: 65536 word (16 address bits) SPI EEPROM
wm0: Ethernet address 00:11:43:e8:01:8d
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb6 at pci5 dev 0 function 2: Intel 6700PXH PCI Express-to-PCI Bridge #1
(rev. 0x09)
ppb6: disabling notification events
pci7 at ppb6 bus 7
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
wm1 at pci7 dev 8 function 0: Intel i82541GI 1000BASE-T Ethernet, rev. 5
wm1: interrupting at ioapic2 pin 1
wm1: 32-bit 66MHz PCI bus
wm1: 65536 word (16 address bits) SPI EEPROM
wm1: Ethernet address 00:11:43:e8:01:8e
igphy1 at wm1 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb7 at pci0 dev 6 function 0: Intel product 0x3599 (rev. 0x09)
pci8 at ppb7 bus 8
pci8: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: Intel 82801EB/ER USB UHCI Controller (rev.
0x02)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 29 function 7: Intel 82801EB/ER USB EHCI Controller (rev.
0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
ppb8 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xc2)
pci9 at ppb8 bus 9
pci9: i/o space, memory space enabled
vga1 at pci9 dev 13 function 0: ATI Technologies Radeon 7000/VE QY (rev.
0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: Intel 82801EB LPC Interface Bridge (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801EB IDE Controller (ICH5) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
attimer0: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2992796400 Hz quality 3000
scsibus0: waiting 2 seconds for devices to settle...
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-STCD-RW/DVD-ROM GCC-4241N, , A101> cdrom
removable
cd0: 32-bit data port
uhub0 at usb0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhub4 at uhub3 port 3: vendor 0x413c product 0xa001, class 9/0, rev
2.00/0.00, addr 2
uhub4: multiple transaction translators
uhub4: 2 ports with 2 removable, self powered
sd0 at scsibus0 target 1 lun 0: <MAXTOR, ATLAS10K5_73SCA, JNZM> disk fixed
sd0: 70007 MB, 81782 cyl, 2 head, 876 sec, 512 bytes/sect x 143374650
sectors
sd0: sync (12.50ns offset 127), 16-bit (160.000MB/s) transfers, tagged
queueing
ses0 at scsibus0 target 6 lun 0: <PE/PV, 1x2 SCSI BP, 1.0> processor fixed
ses0: SAF-TE Compliant Device
ses0: async, 8-bit transfers
ipmi0: version 1.5 interface KCS iobase 0xca8/8 spacing 4
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)



====================== freebsd dmesg ==========================

standard kernel

Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE #0: Fri Feb 18 02:24:46 UTC 2011
root%almeida.cse.buffalo.edu@localhost:/usr/obj/usr/src/sys/GENERIC i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 3.00GHz (2992.71-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf43 Family = f Model = 4 Stepping = 3
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x641d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,CX16,xTPR>
AMD Features=0x20100000<NX,LM>
TSC: P-state invariant
real memory = 3221225472 (3072 MB)
avail memory = 3145670656 (2999 MB)
ACPI APIC Table: <DELL PE BKC >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 2 package(s) x 1 core(s) x 2 HTT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP/HT): APIC ID: 1
cpu2 (AP): APIC ID: 6
cpu3 (AP/HT): APIC ID: 7
ioapic0: Changing APIC ID to 8
ioapic1: Changing APIC ID to 9
ioapic2: Changing APIC ID to 10
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 32-55 on motherboard
ioapic2 <Version 2.0> irqs 64-87 on motherboard
kbd1 at kbdmux0
acpi0: <DELL PE BKC> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib2
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xec00-0xecff mem
0xfe9ff000-0xfe9fffff irq 39 at device 12.0 on pci2
ahc0: [ITHREAD]
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci1
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> at device 0.0 on pci5
pci6: <ACPI PCI bus> on pcib6
em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.3> port 0xdcc0-0xdcff
mem 0xfe6e0000-0xfe6fffff irq 64 at device 7.0 on pci6
em0: [FILTER]
em0: Ethernet address: 00:11:43:e8:01:8d
pcib7: <ACPI PCI-PCI bridge> at device 0.2 on pci5
pci7: <ACPI PCI bus> on pcib7
em1: <Intel(R) PRO/1000 Legacy Network Connection 1.0.3> port 0xccc0-0xccff
mem 0xfe4e0000-0xfe4fffff irq 65 at device 8.0 on pci7
em1: [FILTER]
em1: Ethernet address: 00:11:43:e8:01:8e
pcib8: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci8: <ACPI PCI bus> on pcib8
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xace0-0xacff irq
16 at device 29.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xacc0-0xacdf irq
19 at device 29.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xaca0-0xacbf irq
18 at device 29.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem
0xfeb00000-0xfeb003ff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
pcib9: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci9: <ACPI PCI bus> on pcib9
vgapci0: <VGA-compatible display> port 0xbc00-0xbcff mem
0xf0000000-0xf7ffffff,0xfe1f0000-0xfe1fffff irq 18 at device 13.0 on pci9
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse Explorer, device ID 4
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xec000-0xeffff pnpid
ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: parallel port not found.
p4tcc0: <CPU Frequency Thermal Control> on cpu0
p4tcc1: <CPU Frequency Thermal Control> on cpu1
p4tcc2: <CPU Frequency Thermal Control> on cpu2
p4tcc3: <CPU Frequency Thermal Control> on cpu3
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
acd0: CDRW <HL-DT-STCD-RW/DVD-ROM GCC-4241N/A101> at ata0-master UDMA33
uhub3: 6 ports with 6 removable, self powered
ugen3.2: <vendor 0x413c> at usbus3
uhub4: <vendor 0x413c product 0xa001, class 9/0, rev 2.00/0.00, addr 2> on
usbus3
uhub4: 2 ports with 2 removable, self powered
(probe6:ahc0:0:6:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe6:ahc0:0:6:0): CAM status: SCSI Status Error
(probe6:ahc0:0:6:0): SCSI status: Check Condition
(probe6:ahc0:0:6:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset,
or bus device reset occurred)
ses0 at ahc0 bus 0 scbus0 target 6 lun 0
ses0: <PE/PV 1x2 SCSI BP 1.0> Fixed Processor SCSI-2 device
ses0: 3.300MB/s transfers
ses0: SAF-TE Compliant Device
da0 at ahc0 bus 0 scbus0 target 1 lun 0
da0: <MAXTOR ATLAS10K5_73SCA JNZM> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
da0: Command Queueing enabled
da0: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
Trying to mount root from ufs:/dev/da0s1a
Prev by Date: iwn0 wifi driver error
Next by Date: Power control API
Previous by Thread: iwn0 wifi driver error
Next by Thread: Power control API
Indexes:
Home | Main Index | Thread Index | Old Index