NetBSD-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
HP 620 - first install and where is my wireless?
Hi,
I installed NetBSD 7.0 on an HP 620 laptop. Basically the computer
works, dmesg contains some scary warnings:
What is this?
drm: HPD interrupt storm detected on connector DP-2: switching from
hotplug detection to polling
Could it be related to this issue?
drm: GPU HANG: ecode -1:0x00000000, reason: Command parser error, iir
0x00008010, action: continue
drm: GPU hangs can indicate a bug anywhere in the entire gfx stack,
including userspace.
However, what bothers mee is that I have no wireless itnerface device
shown by ifconfig, nor do I see in dmesg something related. It should be
a Ralink device.
If I activate/deactivate the wlan with the keyboard button, I see this:
ubt0: detached
ubt0: at uhub1 port 1 (addr 2) disconnected
ubt0 at uhub1 port 1
ubt0: Ralink Technology product 0x1000, rev 2.00/52.76, addr 2
Does this mean that after cycling it, the device is seen on the USB bus?
but then there is no driver to manage it?
Missing firmware?
Riccardo
-----
NetBSD 7.0 (GENERIC.201509250726Z)
total memory = 3996 MB
avail memory = 3862 MB
kern.module.path=/stand/amd64/7.0/modules
timecounter: Timecounters tick every 10.000 msec
RTC BIOS diagnostic error
0xef<clock_battery,ROM_cksum,config_unit,fixed_disk,invalid_time>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP 620 (F.08)
mainbus0 (root)
ACPI: RSDP 0xf6970 000024 (v02 HPQOEM)
ACPI: XSDT 0xb9ffe120 000074 (v01 HPQOEM SLIC-MPC 0000000F 01000013)
ACPI: FACP 0xb9ffc000 0000F4 (v03 HPQOEM 1526 0000000F HP 00000001)
ACPI: DSDT 0xb9fdb000 01B62B (v01 HPQOEM 1526 00000001 INTL 20060912)
ACPI: FACS 0xb9fad000 000040
ACPI: HPET 0xb9ffb000 000038 (v01 HPQOEM 1526 00000001 HP 00000001)
ACPI: APIC 0xb9ffa000 000084 (v01 HPQOEM 1526 00000001 HP 00000001)
ACPI: MCFG 0xb9ff9000 00003C (v01 HPQOEM 1526 00000001 HP 00000001)
ACPI: ASF! 0xb9ff8000 0000A0 (v32 HPQOEM 1526 00000001 HP 00000001)
ACPI: SSDT 0xb9fd8000 0002DD (v01 HPQOEM SataAhci 00001000 INTL 20060912)
ACPI: SLIC 0xb9fd6000 000176 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
ACPI: SSDT 0xb9fd5000 00066C (v01 PmRef CpuPm 00003000 INTL 20060912)
ACPI: SSDT 0xb9fd4000 000288 (v01 PmRef Cpu0Tst 00003000 INTL 20060912)
ACPI: SSDT 0xb9fd3000 000225 (v01 PmRef ApTst 00003000 INTL 20060912)
ACPI: All ACPI Tables successfully acquired
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0: Intel(R) Core(TM)2 Duo CPU T6670 @
2.20GHz, id 0x1067a
cpu1 at mainbus0 apid 1: Intel(R) Core(TM)2 Duo CPU T6670 @
2.20GHz, id 0x1067a
acpi0 at mainbus0: Intel ACPICA 20131218
acpi0: X/RSDT: OemId <HPQOEM,SLIC-MPC,0000000f>, AslId < ,01000013>
ACPI: SSDT 0xb9ec6c18 000275 (v01 PmRef Cpu0Ist 00003000 INTL 20060912)
ACPI: SSDT 0x0 000275 (v01 PmRef Cpu0Ist 00003000 INTL 20060912)
ACPI: SSDT 0xb9ec4618 00057B (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
ACPI: SSDT 0x0 00057B (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
ACPI: SSDT 0xb9ec5e18 0001D7 (v01 PmRef ApIst 00003000 INTL 20060912)
ACPI: SSDT 0x0 0001D7 (v01 PmRef ApIst 00003000 INTL 20060912)
ACPI: SSDT 0xb9ec6f18 00008D (v01 PmRef ApCst 00003000 INTL 20060912)
ACPI: SSDT 0x0 00008D (v01 PmRef ApCst 00003000 INTL 20060912)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
acpiec0 at acpi0 (EC0, PNP0C09-1)
: io 0x62,0x66
PDRC (PNP0C02) at acpi0 not configured
acpivga0 at acpi0 (GFX0): ACPI Display Adapter
acpiout0 at acpivga0 (DD01, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (DD02, 0x0400): ACPI Display Output Device
acpiout1: brightness levels: 0 5 10 15 20 25 30 33 36 40 43 46 50 55 60
65 70 75 80 83 86 90 93 96 100
acpiout2 at acpivga0 (DD03, 0x0200): ACPI Display Output Device
acpiout3 at acpivga0 (DD04, 0x0300): ACPI Display Output Device
acpiout4 at acpivga0 (DD05, 0x0005): ACPI Display Output Device
acpivga0: unknown output device acpiout0
acpivga0: unknown output device acpiout2
acpivga0: unknown output device acpiout3
acpivga0: unknown output device acpiout4
acpivga0: connected output devices:
acpivga0: 0x0400 (acpiout1): Unknown Output Device, head 0
FWHD (INT0800) at acpi0 not configured
HTAM (PNP0C02) at acpi0 not configured
LDRC (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, SYN0176) (aux port): irq 12
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery
acpibat0: Hewlett-Packard LIon rechargeable battery
acpibat0: granularity: low->warn 0.100 Ah, warn->full 0.100 Ah
acpiacad0 at acpi0 (AC, ACPI0003): ACPI AC Adapter
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpidalb0 at acpi0 (HST1, PNP0C32-1): Direct Application Launch Button
acpiwmi0 at acpi0 (WMID, PNP0C14-0): ACPI WMI Interface
wmihp0 at acpiwmi0: HP WMI mappings
acpifan0 at acpi0 (FAN6, PNP0C0B-6): ACPI Fan
acpifan1 at acpi0 (FAN7, PNP0C0B-7): ACPI Fan
acpifan2 at acpi0 (FAN8, PNP0C0B-8): ACPI Fan
acpifan3 at acpi0 (FAN9, PNP0C0B-9): ACPI Fan
acpifan4 at acpi0 (FANA, PNP0C0B-10): ACPI Fan
acpifan5 at acpi0 (FANB, PNP0C0B-11): ACPI Fan
acpifan6 at acpi0 (FANG, PNP0C0B-12): ACPI Fan
acpitz0 at acpi0 (GFXZ)
acpitz0: active cooling level 0: 105.0C
acpitz0: active cooling level 1: 96.0C
acpitz0: active cooling level 2: 87.0C
acpitz0: active cooling level 3: 79.0C
acpitz0: active cooling level 4: 71.0C
acpitz0: active cooling level 5: 63.0C
acpitz0: active cooling level 6: 56.0C
acpitz0: levels: critical 108.0 C
acpifan7 at acpi0 (FAN0, PNP0C0B-0): ACPI Fan
acpifan8 at acpi0 (FAN1, PNP0C0B-1): ACPI Fan
acpifan9 at acpi0 (FAN2, PNP0C0B-2): ACPI Fan
acpifan10 at acpi0 (FAN3, PNP0C0B-3): ACPI Fan
acpifan11 at acpi0 (FAN4, PNP0C0B-4): ACPI Fan
acpifan12 at acpi0 (FAN5, PNP0C0B-5): ACPI Fan
acpitz1 at acpi0 (DTSZ)
acpitz1: levels: critical 105.0 C, passive cooling
acpitz2 at acpi0 (CPUZ): cpu0 cpu1
acpitz2: active cooling level 0: 84.0C
acpitz2: active cooling level 1: 74.0C
acpitz2: active cooling level 2: 62.0C
acpitz2: active cooling level 3: 52.0C
acpitz2: active cooling level 4: 44.0C
acpitz2: active cooling level 5: 37.0C
acpitz2: levels: critical 108.0 C, passive 105.0 C
acpitz3 at acpi0 (SKNZ): cpu0 cpu1
acpitz3: levels: critical 105.0 C, passive 95.0 C, passive cooling
acpitz4 at acpi0 (BATZ): cpu0 cpu1
acpitz4: levels: critical 108.0 C, passive 60.0 C, passive cooling
acpitz5 at acpi0 (FDTZ)
acpitz5: levels: critical 110.0 C, passive cooling
ACPI: Enabled 6 GPEs in block 00 to 3F
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_]
(20131218/hwxface-646)
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_]
(20131218/hwxface-646)
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 7.4
pms0: Extended W mode, Palm detect, Multi-finger Report
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x2a40 (rev. 0x07)
agp0 at pchb0: G4X-family chipset
agp0: detected 65020k stolen memory
agp0: aperture at 0xc0000000, size 0x10000000
i915drmkms0 at pci0 dev 2 function 0: vendor 0x8086 product 0x2a42 (rev.
0x07)
drm: Memory usable by graphics device = 512M
drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
drm: Driver supports precise vblank timestamp query.
i915drmkms0: interrupting at ioapic0 pin 16 (i915)
intelfb0 at i915drmkms0
i915drmkms0: info: registered panic notifier
intelfb0: framebuffer at 0xffff800046fd0000, size 1366x768, depth 32,
stride 5504
wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation),
using wskbd0
wsmux1: connecting to wsdisplay0
vendor 0x8086 product 0x2a43 (miscellaneous display, revision 0x07) at
pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2937 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2938 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 17
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x2939 (rev. 0x03)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x293c (rev. 0x03)
ehci0: interrupting at ioapic0 pin 19
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 17
hdafg0 at hdaudio0: Sigmatel 92HD88B3
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: ADC01 2ch: Mic In [Jack]
hdafg0: ADC02 2ch: Mic In [Built-In]
hdafg0: 2ch/2ch 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20
PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdafg1 at hdaudio0: Intel G45 HDMI
hdafg1: HDMI00 8ch: Digital Out [Jack]
hdafg1: 8ch/0ch 48000Hz PCM16*
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x2940 (rev. 0x03)
ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex>
x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2942 (rev. 0x03)
ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex>
x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x1814 product 0x3090 (miscellaneous network) at pci2 dev 0
function 0 not configured
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x2944 (rev. 0x03)
ppb2: PCI Express capability version 1 <Root Port of PCI-E Root Complex>
x1 @ 2.5GT/s
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x2948 (rev. 0x03)
ppb3: PCI Express capability version 1 <Root Port of PCI-E Root Complex>
x1 @ 2.5GT/s
pci4 at ppb3 bus 68
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x294a (rev. 0x03)
ppb4: PCI Express capability version 1 <Root Port of PCI-E Root Complex>
x1 @ 2.5GT/s
pci5 at ppb4 bus 133
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci5 dev 0 function 0: RealTek 8100E/8101E/8102E/8102EL PCIe
10/100BaseTX (rev. 0x02)
re0: interrupting at ioapic0 pin 17
re0: Ethernet address 64:31:50:7b:8f:55
re0: using 256 tx descriptors
rlphy0 at re0 phy 7: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x2934 (rev. 0x03)
uhci3: interrupting at ioapic0 pin 20
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x2935 (rev. 0x03)
uhci4: interrupting at ioapic0 pin 22
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x2936 (rev. 0x03)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x293a (rev. 0x03)
ehci1: interrupting at ioapic0 pin 20
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0x93)
pci6 at ppb5 bus 134
pci6: i/o space, memory space enabled
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2919 (rev.
0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x2929 (rev.
0x03)
ahcisata0: interrupting at ioapic0 pin 21
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP
0xef20ffc3<EMS,CCCS,PSC,SSC,PMD,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 5
isa0 at ichlpcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer1: attached to pcppi0
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
acpicpu0: C2: FFH, lat 57 us, pow 100 mW
acpicpu0: P0: FFH, lat 10 us, pow 35000 mW, 2201 MHz, turbo boost
acpicpu0: P1: FFH, lat 10 us, pow 35000 mW, 2200 MHz
acpicpu0: P2: FFH, lat 10 us, pow 23000 mW, 1600 MHz
acpicpu0: P3: FFH, lat 10 us, pow 15000 mW, 1200 MHz
acpicpu0: T0: FFH, lat 1 us, pow 15000 mW, 100 %
acpicpu0: T1: FFH, lat 1 us, pow 13125 mW, 88 %
acpicpu0: T2: FFH, lat 1 us, pow 11250 mW, 75 %
acpicpu0: T3: FFH, lat 1 us, pow 9375 mW, 63 %
acpicpu0: T4: FFH, lat 1 us, pow 7500 mW, 50 %
acpicpu0: T5: FFH, lat 1 us, pow 5625 mW, 38 %
acpicpu0: T6: FFH, lat 1 us, pow 3750 mW, 25 %
acpicpu0: T7: FFH, lat 1 us, pow 1875 mW, 13 %
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
drm: GPU HANG: ecode -1:0x00000000, reason: Command parser error, iir
0x00008010, action: continue
drm: GPU hangs can indicate a bug anywhere in the entire gfx stack,
including userspace.
drm: Please file a _new_ bug report on bugs.freedesktop.org against DRI
-> DRM/Intel
drm: drm/i915 developers can then reassign to the right component if
it's not a kernel issue.
drm: The gpu crash dump is required to analyze gpu hangs, so please
always attach it.
drm: GPU crash dump saved to /sys/class/drm/card0/error
render error detected, EIR: 0x00000010
IPEIR: 0x00000000
IPEHR: 0x00000000
INSTDONE_0: 0xfffffffe
INSTDONE_1: 0xffffffff
INSTDONE_2: 0x00000000
INSTDONE_3: 0x00000000
INSTPS: 0x00000000
ACTHD: 0x00000000
page table error
PGTBL_ER: 0x00000010
DRM error in i915_report_and_clear_eir: EIR stuck: 0x00000010, masking
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter online.
IPsec: Initialized Security Association Processing.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 6 ports with 6 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 1: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0
wd0: <SAMSUNG HM321HI>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6
(Ultra/133) (using DMA)
atapibus0 at atabus1: 1 targets
cd0 at atapibus0 drive 0: <hp DVDRAM GT30L, KW8ACJN2906, mP04>
cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
(Ultra/100) (using DMA)
ubt0 at uhub1 port 1
ubt0: vendor 0x148f product 0x1000, rev 2.00/52.76, addr 2
uvideo0 at uhub3 port 5 configuration 1 interface 0: Foxlink HP Webcam
[2 MP Fixed], rev 2.00/1.06, addr 2
video0 at uvideo0: Foxlink HP Webcam [2 MP Fixed], rev 2.00/1.06, addr 2
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
drm: HPD interrupt storm detected on connector DP-2: switching from
hotplug detection to polling
Home |
Main Index |
Thread Index |
Old Index