Re: Status of run0 on armv7 NetBSD 8.0_RC1 rpi2

[Mayuresh <mayuresh%acm.org@localhost>]

On Tue, Jun 12, 2018 at 02:45:58PM +0200, Leonardo Taccari wrote:
> Can you please share relevant part of /etc/wpa_supplicant.conf (probably
> just the:
> 
>  | network={
>  |     ...
>  | }

It's taken from a working conf on Linux. It's correct.

> lines will be enough), `wpa_cli scan_res' output of the corresponding
> ssid and more information when invoking just `wpa_cli' interactively?


scan_res is blank as ifconfig does not show ssid as set. If set by running
ifconfig run0 ssid, it appears for a few seconds and goes away.

wpa_clie keeps repeating these:

  21:33:08.812: CTRL-EVENT-SCAN-RESULTS 
  21:33:08.812: CTRL-EVENT-NETWORK-NOT-FOUND 


> (the latter will contain information if, for example, the
> psk/credentials are not correct that can be missed if `wpa_cli scan' is
> not called at that exact time and will hopefully help to debug that
> further!)

I am also sharing debug output, though I didn't find anything specific in
it.

# /etc/rc.d/wpa_supplicant restart
Stopping wpa_supplicant.
Starting wpa_supplicant.
wpa_supplicant v2.6
Successfully initialized wpa_supplicant
Initializing interface 'run0' conf '/etc/wpa_supplicant.conf' driver
'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' ->
'/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='wheel'
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=6):
     50 68 6f 74 6f 6e                                 Photon          
PSK - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='Photon'
Add interface run0 to a new radio N/A
run0: Own MAC address: 00:c1:00:c1:94:b6
bsd_set_key: alg=0 addr=0x0 key_idx=0 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=0
bsd_set_key: alg=0 addr=0x0 key_idx=1 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=1
bsd_set_key: alg=0 addr=0x0 key_idx=2 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=2
bsd_set_key: alg=0 addr=0x0 key_idx=3 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=3
wpa_driver_bsd_set_countermeasures: enabled=0
run0: RSN: flushing PMKID list in the driver
run0: Setting scan request: 0.100000 sec
ENGINE: Loading dynamic engine
ENGINE: Loading dynamic engine
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Using existing control interface directory.
ctrl_interface_group=0 (from group name 'wheel')
run0: Added interface run0
run0: State: DISCONNECTED -> DISCONNECTED
Daemonize..

Mayuresh