--Multipart_Wed_Sep__2_20:36:28_1998-1
Content-Type: text/plain; charset=US-ASCII


> ftp://ftp.feral.com/outgoing/isptest/netbsd.alpha.gz

It works for me. This message is a bit puzzling, though:

isp0: Target 1 Sync Mode at 20MHZ, Tagged Queueing Enabled

I very much doubt that target 1 can do 20MHz (btw, small typo there,
the unit is Herz abbr. Hz). Is this as it should be, or does it
indicate some kind of problem?

I'll push some more bits through the controller over the night.

/Johan


--Multipart_Wed_Sep__2_20:36:28_1998-1
Content-Type: text/plain; charset=US-ASCII

NetBSD 1.3G (ALPHA) #24: Wed Sep  2 08:46:12 PDT 1998
    mjacob@nobble.feral.com:/space/isp_test/arch/alpha/compile/ALPHA
Digital Personal WorkStation 500au, 500MHz
8192 byte page size, 1 processor.
real mem = 134217728 (1933312 reserved for PROM, 132284416 used by NetBSD)
avail mem = 111566848
using 1614 buffers containing 13221888 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A (reserved minor type)
cpu0: VAX FP support, IEEE FP support, Primary Eligible
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config access
cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
pci0 at cia0 bus 0
pci0: i/o enabled, memory enabled
de0 at pci0 dev 3 function 0
de0: interrupting at dec 550 irq 8
de0: DEC 21143 [10-100Mb/s] pass 3.0
de0: address 00:00:f8:75:6d:9a
de0: enabling 10baseT port
pciide0 at pci0 dev 4 function 0: CMD Technology PCI0646 (rev. 0x01)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel wired to compatibility mode
wdc2 at pciide0 channel 0
atapibus0 at wdc2
cd0 at atapibus0 drive 0: <CRD-8241B, 1997/09/18, 2.01> type 5 cdrom removable
pciide0: secondary channel wired to compatibility mode
pciide0: secondary channel ignored (not responding; disabled or no drives?)
sio0 at pci0 dev 7 function 0: Intel 82378ZB System I/O (SIO) (rev. 0x43)
Digital Equipment TGA2 (VGA display, revision 0x22) at pci0 dev 12 function 0 not configured
ppb0 at pci0 dev 20 function 0: Digital Equipment DECchip 21052 PCI-PCI Bridge (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o enabled, memory enabled
isp0 at pci1 dev 9 function 0
Qlogic ISP Driver, NetBSD (pci) Platform Version 0.97 Core Version 1.2
isp0: setting input clock to 60
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.54
isp0: interrupting at dec 550 irq 24
scsibus0 at isp0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <DEC, RZ1CC-BA (C) DEC, 880F> SCSI2 0/direct fixed
sd0: 4091MB, 3708 cyl, 20 head, 113 sec, 512 bytes/sect x 8380080 sectors
sd1 at scsibus0 targ 1 lun 0: <DEC, DSP3105S, T384> SCSI2 0/direct fixed
sd1: 1001MB, 2570 cyl, 14 head, 57 sec, 512 bytes/sect x 2050860 sectors
sd2 at scsibus0 targ 4 lun 0: <SEAGATE, ST118273W, 5698> SCSI2 0/direct fixed
sd2: 17366MB, 7501 cyl, 20 head, 237 sec, 512 bytes/sect x 35566480 sectors
fpa0 at pci1 dev 10 function 0: DEC DEFPA PCI FDDI SAS Controller
fpa0: FDDI address 00:00:f8:40:b2:23, FW=3.10, HW=1, SMT V7.2
fpa0: FDDI Port = S (PMD = ANSI Multi-Mode)
fpa0: interrupting at dec 550 irq 28
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
wsdisplay0 at vga0
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pckbc0 at isa0 port 0x60-0x64
pckbdprobe: reset error 5
psmprobe: reset error 5
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
root on sd2a dumps on sd2b
isp0: Target 4 Sync Mode at 20MHZ, Wide Bus, Tagged Queueing Enabled
mountroot: trying nfs...
mountroot: trying ext2fs...
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying ffs...
root file system type: ffs

--Multipart_Wed_Sep__2_20:36:28_1998-1--