On Thu, Dec 30, 1999 at 01:12:49PM -0800, Jeff Roberson wrote:
> The install floppies are located at the following address:
> ftp://ftp.netbsd.org/pub/NetBSD/arch/alpha/1.4.2_ALPHA/alpha/installation/floppy
> 
> Do you have the same cia0 extended capabilities?  It should stall shortly
> after detecting cia0.  Thanks for the help.

refering to my previous post:

<STEAM VALVE OPEN>
would you believe the SRM is prepared to talk to you
on serial port#2 (note: #2) too? Well, it does. NetBSD rightfully believes
the console should be at #1. I had the cable misconnected to #2, which is
what you get when you dive under a table without flashlight.
</STEAM VALVE>

Anyway:

NetBSD 1.4.2_ALPHA (INSTALL) #1: Tue Dec 21 07:41:53 MET 1999
    he@albatross.runit.sintef.no:/usr/src/sys/arch/alpha/compile/INSTALL
Digital Personal WorkStation 600au, 598MHz
8192 byte page size, 1 processor.
real mem = 134217728 (2039808 reserved for PROM, 132177920 used by NetBSD)
avail mem = 110264320
using 1613 buffers containing 13213696 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A-0 ()
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config access
cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
pci0 at cia0 bus 0
pci0: i/o enabled, memory enabled
de0 at pci0 dev 3 function 0
de0: interrupting at dec 550 irq 8
de0: DEC 21142 [10-100Mb/s] pass 1.1
de0: address 00:00:f8:75:3c:6a
de0: enabling 100baseTX port
pciide0 at pci0 dev 4 function 0: CMD Technology PCI0646
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0: secondary channel wired to compatibility mode
pciide0: disabling secondary channel (no drives)
sio0 at pci0 dev 7 function 0: vendor 0x8086 product 0x0484 (rev. 0x43)
ppb0 at pci0 dev 8 function 0: vendor 0x1011 product 0x0024 (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o enabled, memory enabled
isp0 at pci1 dev 8 function 0
isp0: interrupting at dec 550 irq 20
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.57
isp0: driver initiated bus reset
scsibus0 at isp0: 16 targets, 8 luns per target
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST34371W, 0702> SCSI2 0/direct fixed
sd0: 4095MB, 5899 cyl, 10 head, 142 sec, 512 bytes/sect x 8388314 sectors
sd1 at scsibus0 targ 1 lun 0: <IBM, DDRS-34560W, S97B> SCSI2 0/direct fixed
sd1: 4357MB, 8387 cyl, 5 head, 212 sec, 512 bytes/sect x 8925000 sectors
cd0 at scsibus0 targ 6 lun 0: <DEC, RRD46   (C) DEC, 0557> SCSI2 5/cdrom
removab
le
vga0 at pci0 dev 12 function 0: vendor 0x5333 product 0x88c1 (rev. 0x00)
wsdisplay0 at vga0
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pckbc0 at isa0 port 0x60-0x64
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
md0: internal 3072K image area
WARNING: can't figure what device matches "DVA 1 0 0 0 0 0 0"
root on md0a dumps on md0b
WARNING: clock gained 9 days -- CHECK AND RESET THE DATE!
root file system type: ffs
Terminal type? [vt100] 

Looks ok to me.

-- 
Wilko Bulte 		Arnhem, The Netherlands	  - The FreeBSD Project 
    			WWW : http://www.tcja.nl  http://www.freebsd.org