Having problems with a new XP1000:

- loaded 1.4.1 (up and limping - works fine on old XP1000/500MHz)
- "upgraded" to 1.4P (snapshot 19991223) due to SCSI problems
- getting "stray 6600 irq 47" messages, then messages about the
  SCSI controller having loaded an earlier firmware. These
  messages appear when accessing the disk (like gunzip'ing a
  file):

isp0: Ultra Mode Capable
isp0: Board Revision 1040C, loaded F/W Revision 4.65.0
isp0: Last F/W revision was 5.57.1
isp0: 243 max I/O commands supported
isp0: enabled FW features (0x1)

- system dies subsequently

System specs (short version):

- 21264A-8 667MHz (CPU not recognized, see below)
- 1024 MB RAM
- Firmware 5.6-11

Boot messages follow:

Jan  6 05:02:11 host /netbsd: NetBSD 1.4P (GENERIC) #1: Sun Jan  2 09:29:48 PST 2000
Jan  6 05:02:11 host /netbsd:     toddpw@chewie.toddpw.net:/usr/src/sys/arch/alpha/compile/GENERIC
Jan  6 05:02:11 host /netbsd: COMPAQ Professional Workstation XP1000, 666MHz
Jan  6 05:02:11 host /netbsd: 8192 byte page size, 1 processor.
Jan  6 05:02:11 host /netbsd: total memory = 1024 MB
Jan  6 05:02:12 host /netbsd: (1816 KB reserved for PROM, 1022 MB used by NetBSD)
Jan  6 05:02:12 host /netbsd: avail memory = 945 MB
Jan  6 05:02:12 host /netbsd: using 6555 buffers containing 52440 KB of memory
Jan  6 05:02:12 host /netbsd: mainbus0 (root)
Jan  6 05:02:12 host /netbsd: cpu0 at mainbus0: ID 0 (primary), UNKNOWN CPU TYPE (11:8)tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
Jan  6 05:02:12 host /netbsd: tsc0: 4 Dchips, 1 memory bus of 32 bytes
Jan  6 05:02:12 host /netbsd: tsc0: arrays present: 1024MB, 0MB, 0MB, 0MB, Dchip 0 rev 1
Jan  6 05:02:12 host /netbsd: tsp0 at tsc0
Jan  6 05:02:12 host /netbsd: pci0 at tsp0 bus 0
Jan  6 05:02:12 host /netbsd: pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
Jan  6 05:02:12 host /netbsd: sio0 at pci0 dev 7 function 0: Contaq Microsystems 82C693 PCI-ISA Bridge (rev. 0x00)
Jan  6 05:02:12 host /netbsd: pciide0 at pci0 dev 7 function 1: Contaq Microsystems CY82C693 IDE Controller
Jan  6 05:02:12 host /netbsd: pciide0: bus-master DMA support present
Jan  6 05:02:12 host /netbsd: pciide0: primary channel wired to compatibility mode
Jan  6 05:02:12 host /netbsd: atapibus0 at pciide0 channel 0
Jan  6 05:02:12 host /netbsd: cd0 at atapibus0 drive 0: <Compaq  CRD-8322B, 1999/02/11, 1.07> type 5 cdrom removable
Jan  6 05:02:12 host /netbsd: cd0: 32-bits data port
Jan  6 05:02:12 host /netbsd: cd0: drive supports PIO mode 4, DMA mode 2
Jan  6 05:02:12 host /netbsd: cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
Jan  6 05:02:12 host /netbsd: pciide1 at pci0 dev 7 function 2: Contaq Microsystems CY82C693 IDE Controller
Jan  6 05:02:13 host /netbsd: pciide1: hardware does not support DMA
Jan  6 05:02:13 host /netbsd: pciide1: primary channel wired to compatibility mode
Jan  6 05:02:13 host /netbsd: pciide1: disabling primary channel (no drives)
Jan  6 05:02:13 host /netbsd: ohci0 at pci0 dev 7 function 3: Contaq Microsystems 82C693 PCI-ISA Bridge (rev. 0x00)
Jan  6 05:02:13 host /netbsd: intr_map: line=0xea, no mapping for 0/7/3
Jan  6 05:02:13 host /netbsd: ohci0: couldn't map interrupt
Jan  6 05:02:13 host /netbsd: ti0 at pci0 dev 11 function 0: can't map i/o space
Jan  6 05:02:13 host /netbsd: fpa0 at pci0 dev 12 function 0: DEC DEFPA PCI FDDI DAS Controller
Jan  6 05:02:13 host /netbsd: fpa0: FDDI address <erased>, FW=3.10, HW=0, SMT V7.2
Jan  6 05:02:13 host /netbsd: fpa0: FDDI Port[A] = A (PMD = ANSI Multi-Mode), FDDI Port[B] = B (PMD = ANSI Multi-Mode)
Jan  6 05:02:13 host /netbsd: fpa0: interrupting at dec_6600 irq 36
Jan  6 05:02:13 host /netbsd: vga0 at pci0 dev 13 function 0: Texas Instruments TVP4020 Permedia 2 (rev. 0x01)
Jan  6 05:02:13 host /netbsd: wsdisplay0 at vga0: console (80x25, vt100 emulation)
Jan  6 05:02:13 host /netbsd: isa0 at sio0
Jan  6 05:02:13 host /netbsd: com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
Jan  6 05:02:13 host /netbsd: com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
Jan  6 05:02:13 host /netbsd: pckbc0 at isa0 port 0x60-0x64
Jan  6 05:02:13 host /netbsd: pckbd0 at pckbc0 (kbd slot)
Jan  6 05:02:13 host /netbsd: pckbc0: using irq 1 for kbd slot
Jan  6 05:02:13 host /netbsd: wskbd0 at pckbd0: console keyboard, using wsdisplay0
Jan  6 05:02:13 host /netbsd: pms0 at pckbc0 (aux slot)
Jan  6 05:02:13 host /netbsd: pckbc0: using irq 12 for aux slot
Jan  6 05:02:13 host /netbsd: wsmouse0 at pms0
Jan  6 05:02:13 host /netbsd: lpt0 at isa0 port 0x3bc-0x3bf irq 7
Jan  6 05:02:13 host /netbsd: sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.01
Jan  6 05:02:13 host /netbsd: audio0 at sb0: half duplex, mmap, independent
Jan  6 05:02:13 host /netbsd: midi at sb0 not configured
Jan  6 05:02:13 host /netbsd: opl at sb0 not configured
Jan  6 05:02:13 host /netbsd: pcppi0 at isa0 port 0x61
Jan  6 05:02:13 host /netbsd: spkr0 at pcppi0
Jan  6 05:02:13 host /netbsd: isabeep0 at pcppi0
Jan  6 05:02:13 host /netbsd: fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
Jan  6 05:02:13 host /netbsd: fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Jan  6 05:02:13 host /netbsd: mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
Jan  6 05:02:13 host /netbsd: tsp1 at tsc0
Jan  6 05:02:13 host /netbsd: pci1 at tsp1 bus 0
Jan  6 05:02:13 host /netbsd: pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
Jan  6 05:02:13 host /netbsd: de0 at pci1 dev 3 function 0
Jan  6 05:02:13 host /netbsd: de0: interrupting at dec_6600 irq 45
Jan  6 05:02:13 host /netbsd: de0: DEC 21143 [10-100Mb/s] pass 4.1
Jan  6 05:02:13 host /netbsd: de0: address <erased>
Jan  6 05:02:13 host /netbsd: de0: enabling 10baseT port
Jan  6 05:02:13 host /netbsd: de0: supplying EUI64: <erased>
Jan  6 05:02:13 host /netbsd: isp0 at pci1 dev 6 function 0
Jan  6 05:02:13 host /netbsd: isp0: interrupting at dec_6600 irq 47
Jan  6 05:02:13 host /netbsd: isp0: Ultra Mode Capable
Jan  6 05:02:13 host /netbsd: isp0: Board Revision 1040C, loaded F/W Revision 4.65.0
Jan  6 05:02:13 host /netbsd: isp0: Last F/W revision was 5.57.1
Jan  6 05:02:13 host /netbsd: isp0: 243 max I/O commands supported
Jan  6 05:02:13 host /netbsd: isp0: enabled FW features (0x1)
Jan  6 05:02:13 host /netbsd: isp0: driver initiated bus reset of bus 0
Jan  6 05:02:13 host /netbsd: scsibus0 at isp0: 16 targets, 8 luns per target
Jan  6 05:02:13 host /netbsd: ppb0 at pci1 dev 8 function 0: Digital Equipment DECchip 21152 PCI-PCI Bridge (rev. 0x03)
Jan  6 05:02:13 host /netbsd: pci2 at ppb0 bus 2
Jan  6 05:02:13 host /netbsd: pci2: i/o space, memory space enabled, rd/line, wr/inv ok
Jan  6 05:02:13 host /netbsd: de1 at pci2 dev 9 function 0
Jan  6 05:02:13 host /netbsd: de1: interrupting at dec_6600 irq 28
Jan  6 05:02:13 host /netbsd: de1: DEC DE500-BA 21143 [10-100Mb/s] pass 3.0
Jan  6 05:02:13 host /netbsd: de1: address <erased>
Jan  6 05:02:13 host /netbsd: de1: enabling 10baseT port
Jan  6 05:02:13 host /netbsd: scsibus0: waiting 2 seconds for devices to settle...
Jan  6 05:02:13 host /netbsd: isp0: Bus 0 Target 0 Async Mode
Jan  6 05:02:13 host /netbsd: sd0 at scsibus0 targ 0 lun 0: <COMPAQ, BB01821AC3, 3B05> SCSI2 0/direct fixed
Jan  6 05:02:13 host /netbsd: sd0: 17365 MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sect x 35565080 sectors
Jan  6 05:02:13 host /netbsd: isp0: Bus 0 Target 1 Async Mode
Jan  6 05:02:13 host /netbsd: sd1 at scsibus0 targ 1 lun 0: <COMPAQ, BB01821AC3, 3B05> SCSI2 0/direct fixed
Jan  6 05:02:13 host /netbsd: sd1: 17365 MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sect x 35565080 sectors
Jan  6 05:02:13 host /netbsd: isp0: Bus 0 Target 2 Async Mode
Jan  6 05:02:13 host /netbsd: sd2 at scsibus0 targ 2 lun 0: <COMPAQ, BB01821AC3, 3B05> SCSI2 0/direct fixed
Jan  6 05:02:13 host /netbsd: sd2: 17365 MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sect x 35565080 sectors
Jan  6 05:02:13 host /netbsd: isp0: Bus 0 Target 3 Async Mode
Jan  6 05:02:13 host /netbsd: sd3 at scsibus0 targ 3 lun 0: <COMPAQ, BB01821AC3, 3B05> SCSI2 0/direct fixed
Jan  6 05:02:13 host /netbsd: sd3: 17365 MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sect x 35565080 sectors
Jan  6 05:02:13 host /netbsd: root on sd0a dumps on sd0b
Jan  6 05:02:13 host /netbsd: isp0: Bus 0 Target 0 at 20MHz Max Offset 8, 16 bit wide, Tagged Queueing Enabled
Jan  6 05:02:13 host last message repeated 8 times
Jan  6 05:02:13 host /netbsd: root file system type: ffs
Jan  6 05:02:13 host /netbsd: de0: enabling 10baseT port
Jan  6 05:02:13 host /netbsd: de0: starting DAD for <erased>
Jan  6 05:02:13 host /netbsd: de0: DAD complete for <erased> - no duplicates found
Jan  6 05:02:10 host savecore: no core dump

There is also the issue of the DEGPA-SX gigabit card not getting quite
recognized (see the "ti0" line), but that's secondary at this
point.

Any thoughts? The system is not really usable at either 1.4.1 or
1.4P.

Sven