Bert Kiers wrote:

>>I can't provide dmesg output since the kernel message buffer is
>>overwritten by now with those messages) with currently no targets
> 
> you can still find them in /var/run/dmesg.boot

Ah, thanks!  I already had some notion of such a file in my mind
but was looking for it in /var/log and didn't search any further
when I didn't find it there.

Well, here's the complete dmesg.boot:


consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 1.6_BETA2 (GENERIC) #0: Wed Jun 19 18:30:37 MEST 2002
     bouyer@java:/home/tmp/alpha/obj/sys/arch/alpha/compile/GENERIC
Digital Personal WorkStation 600au, 598MHz, s/n
8192 byte page size, 1 processor.
total memory = 1536 MB
(1896 KB reserved for PROM, 1534 MB used by NetBSD)
avail memory = 1420 MB
using 9831 buffers containing 78648 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A-0
cpu0: Architecture extensions: 1<BWX>
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config access
sio_intr_setup: 0 level-triggered
pci0 at cia0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
tlp0 at pci0 dev 3 function 0: DECchip 21143 Ethernet, pass 3.0
tlp0: interrupting at dec 550 irq 0
tlp0: DEC , Ethernet address 00:00:f8:76:34:17
nsphy0 at tlp0 phy 5: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
sio0 at pci0 dev 7 function 0: Contaq Microsystems 82C693 PCI-ISA Bridge 
(rev. 0x00)
pciide0 at pci0 dev 7 function 1: Cypress 82C693 IDE Controller (rev. 0x00)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
atapibus0 at pciide0 channel 0: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA CD-ROM XM-6202B, 
b\134221\134311\134373\134000, 1110> type 5 cdro
m removable
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: primary channel interrupting at isa irq 14
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide1 at pci0 dev 7 function 2: Cypress 82C693 IDE Controller (rev. 0x00)
pciide1: device disabled (at device)
ohci0 at pci0 dev 7 function 3: Contaq Microsystems 82C693 PCI-ISA 
Bridge (rev. 0x00)
ohci0: interrupting at isa irq 10
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Contaq Microsys OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
tga0 at pci0 dev 11 function 0: TGA2 pass 2, board type T8-02
tga0: 1280 x 1024, 8bpp, Bt485 RAMDAC
tga0: interrupting at dec 550 irq 4
wsdisplay0 at tga0 (kbdmux ignored)
ppb0 at pci0 dev 20 function 0: Digital Equipment DECchip 21152 PCI-PCI 
Bridge (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
isp0 at pci1 dev 4 function 0: QLogic 1020 Ultra Wide SCSI HBA
isp0: interrupting at dec 550 irq 3
scsibus0 at isp0: 16 targets, 8 luns per target
ahc0 at pci1 dev 10 function 0
ahc0: interrupting at dec 550 irq 20
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc0: 16 targets, 8 luns per target
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
wsdisplay1 at vga0 (kbdmux ignored)
lpt0 at isa0 port 0x3bc-0x3bf irq 7
sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.01
audio0 at sb0: half duplex, mmap, independent
midi at sb0 not configured
opl at sb0 not configured
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <IBM, DDRS-34560W, S71D> SCSI2 0/direct 
fixed
sd0: 4357 MB, 8387 cyl, 5 head, 212 sec, 512 bytes/sect x 8925000 sectors
sd0: sync (100.0ns offset 8), 16-bit (20.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <IBM, DDRS-34560W, S71D> SCSI2 0/direct 
fixed
sd1: 4357 MB, 8387 cyl, 5 head, 212 sec, 512 bytes/sect x 8925000 sectors
sd1: sync (100.0ns offset 8), 16-bit (20.000MB/s) transfers, tagged queueing
sd2 at scsibus0 target 4 lun 0: <DEC, RZ1CB-BS (C) DEC, 0818> SCSI2 
0/direct fixed
sd2: 4091 MB, 3708 cyl, 20 head, 113 sec, 512 bytes/sect x 8380080 sectors
sd2: sync (100.0ns offset 8), 16-bit (20.000MB/s) transfers, tagged queueing
scsibus1: waiting 2 seconds for devices to settle...
Kernelized RAIDframe activated
sd1: no disk label
sd2: no disk label
root on sd0a dumps on sd0b
root file system type: ffs


--mkb