Hello Nigel,
The IRQ bug only fixed in -current, so you should try
http://nycdn.netbsd.org/pub/NetBSD-daily/HEAD/202112251840Z/images/NetBSD-9.99.93-alpha.iso
--
istvan
Hi, I'm new to this group but have been on NetBSD-VAX for quite som etime.
I have an Alpha with VMS on it, bit am trying to get NetBSD running so as to be able to use a SCSI disk that somebody gave me.
The disk is 77GB and won't format under VMS. It tries to then gets all sorts of errors due to misreading the geometry, I guess.
I downloaded and dd'ed an ISO and it starts to boot in the CD of the Alpha, but hangs after accessing the floppy:
>>> boo dka400
INIT-S-CPU...
AUDIT_BOOT_STARTS ...
AUDIT_CHECKSUM_GOOD
AUDIT_LOAD_BEGINS
AUDIT_LOAD_DONE
NetBSD/alpha 9.2 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 9.2 Secondary Bootstrap, Revision 1.13 (Wed May 12 13:15:55 UTC 2021)
VMS PAL rev: 0x100010530
OSF PAL rev: 0x20123
Switch to OSF PAL code succeeded.
Boot flags: 0,0
11014768+206128=0xab3d90
Entering netbsd at 0xfffffc0000a011a0...
[ 1.0000000] Unrecognized boot flag '0'.
[ 1.0000000] Unrecognized boot flag ','.
[ 1.0000000] Unrecognized boot flag '0'.
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
[ 1.0000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
[ 1.0000000] 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 9.2 (INSTALL) #0: Wed May 12 13:15:55 UTC 2021
[ 1.0000000] mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/alpha/compile/INSTALL
[ 1.0000000] DEC2000 model 300, 150MHz, s/n
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 256 MB
[ 1.0000000] (2048 KB reserved for PROM, 254 MB used by NetBSD)
[ 1.0000000] avail memory = 239 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21064-0
[ 1.0000000] jensenio0 at mainbus0
[ 1.0000000] pckbc0 at jensenio0 port 0x60
[ 1.0000000] com0 at jensenio0 port 0x3f8: ns8250 or ns16450, no fifo
[ 1.0000000] com0: console
[ 1.0000000] com0: interrupting at vector 0x900
[ 1.0000000] com1 at jensenio0 port 0x2f8: ns8250 or ns16450, no fifo
[ 1.0000000] com1: interrupting at vector 0x920
[ 1.0000000] lpt0 at jensenio0 port 0x3bc
[ 1.0000000] lpt0: interrupting at eisa irq 1
[ 1.0000000] mcclock0 at jensenio0 port 0x170: mc146818 compatible time-of-day clock
[ 1.0000000] eisa0 at jensenio0
[ 1.0000000] device CPQ3111 at eisa0 slot 1 not configured
[ 1.0000000] depca2 at eisa0 slot 2: DEC DE422 Ethernet
[ 1.0000000] depca2: shared memory at 0xd0000-0xdffff
[ 1.0000000] le0 at depca2
[ 1.0000000] le0: failed to clear memory at 0 (0xff != 0xaa)
[ 1.0000000] ahb0 at eisa0 slot 6: Adaptec AHA-1742A SCSI
[ 1.0000000] ahb0: interrupting at eisa irq 12
[ 1.0000000] scsibus0 at ahb0: 8 targets, 8 luns per target
[ 1.0000000] isa0 at jensenio0
[ 1.0000000] vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
Has anybody seen this problem before that maybe knows a solution? Or how to disable testing the isa floppy drive at all?
btw the console shows it as under-sized! It is DKA200:
>> sho dev
BOOTDEV ADDR DEVTYPE RM/FX DEVNAM REV NUMBYTES
------- ---- ------- ----- ------ --- --------
ERA0 08-00-2B-BB-88-6B
DVA0 PC Floppy DISK RM
SCSI Devices..
DKA0 A/0/0 DISK FX RZ28 D41C 2.10GB
DKA100 A/1/0 DISK FX RZ28 D41C 2.10GB
DKA200 A/2/0 DISK FX ST11827 6244 1.03GB
DKA400 A/4/0 RODISK RM RRD44 1094 ......
MKA500 A/5/0 TAPE RM TLZ06 0491 ......
HOST A/7/0 PROC AHA1742A G.2
>>>
Thanks in advance,
Nigel
-- Nigel Johnson, MSc., MIEEE, MCSE VE3ID/G4AJQ/VA3MCU Amateur Radio, the origin of the open-source concept! Skype: TILBURY2591 nw.johnson%ieee.org@localhost