On Wed, Dec 19, 2007 at 09:21:03AM -0500, Alex DuBois wrote:
> On Tue, Dec 18, 2007 at 08:15:44PM -0500, Jared D. McNeill wrote:
> > On Tue, 18 Dec 2007, Alex DuBois wrote:
> > Curious, do your USB ports work on resume? I haven't had any luck bringing 
> > them alive on my T61, not sure how similar the x61s is..
> > Jared
> 
> I didn't think to try the USB ports, and you're right about them not
> working on resume. However, the light on my USB flash drive turned on
> for less than a second, though demesg has no mention of it. I had to try
> all the ports several times to get it to do that. I haven't been able to
> reproduce it.
> Alex

UPDATE: The USB ports on my docking station are working correctly after a
suspend/resume, the others are not.

You can see it working here:

umass0 at uhub6 port 1 configuration 1 interface 0
umass0: SanDisk Corporation U3 Cruzer Micro, rev 2.00/0.10, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, U3 Cruzer Micro, 2.18> disk
removable
sd0: 979 MB, 1990 cyl, 16 head, 63 sec, 512 bytes/sect x 2006673 sectors

acpi0: entering state 3
Flushing disk caches: 1 done

ioapic0 reenabling
ehci0: BIOS has given up ownership
azalia0: RIRB time out
azalia0: RIRB time out
ehci1: BIOS has given up ownership
ahcisata0 port 0: device present, speed: 1.5Gb/s
ahcisata0 port 0: device present, speed: 1.5Gb/s
umass0: at uhub6 port 1 (addr 3) disconnected
sd0 detached
scsibus0 detached
umass0 detached
umass0 at uhub6 port 1 configuration 1 interface 0
umass0: SanDisk Corporation U3 Cruzer Micro, rev 2.00/0.10, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, U3 Cruzer Micro, 2.18> disk
removable
sd0: 979 MB, 1990 cyl, 16 head, 63 sec, 512 bytes/sect x 2006673 sectors
wd0f: device timeout writing fsbn 524784 of 524784-524799 (wd0 bn
46729551; cn 46358 tn 10 sn 57), retrying
ahcisata0 port 0: device present, speed: 1.5Gb/s
wd0: soft error (corrected)
umass0: at uhub6 port 1 (addr 3) disconnected
sd0 detached
scsibus0 detached
umass0 detached
uhidev0 at uhub6 port 2 configuration 1 interface 0
uhidev0: Silitek IBM USB Keyboard, rev 1.10/1.00, addr 3, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub6 port 2 configuration 1 interface 1
uhidev1: Silitek IBM USB Keyboard, rev 1.10/1.00, addr 3, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 3: input=3, output=1, feature=0
uhidev2 at uhub6 port 1 configuration 1 interface 0
uhidev2: IBM product 0x310b, rev 2.00/1.10, addr 4, iclass 3/1
ums0 at uhidev2: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0

--
Alex