lockup of Atom 330 machine?

To: port-amd64%netbsd.org@localhost
Subject: lockup of Atom 330 machine?
From: Jörn Clausen <joernc%googlemail.com@localhost>
Date: Wed, 1 Dec 2010 20:36:58 +0100
Hi!

I just migrated my personal web server to an Atom 330 based machine.
After about one day "in the wild", the machine locked up. According to
the logs (e.g. /var/log/cron) the machine was completely frozen until
I resetted it. A dmesg output is attached. Are there any known
problems with this hardware? Is there anything I can trim from the
kernel? I have no physical access to the machine, so I am limited in
my possibilities to debug it.

cpuid reports

"         Intel(R) Atom(TM) CPU D510   @ 1.66GHz"

dmesg output is (MAC address removed)

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (GENERIC) #0: Sat Nov  6 13:19:33 UTC 2010
        
builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5-1-RELEASE/amd64/201011061943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/amd64/compile/GENERIC
total memory = 2031 MB
avail memory = 1953 MB
timecounter: Timecounters tick every 10.000 msec
RTC BIOS diagnostic error 80<clock_battery>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.5 @ 0xe4410 (25 entries)
                                                                  (
                    )
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1666MHz, id 0x106ca
cpu1 at mainbus0 apid 1: Intel 686-class, 1666MHz, id 0x106ca
cpu2 at mainbus0 apid 2: Intel 686-class, 1666MHz, id 0x106ca
cpu3 at mainbus0 apid 3: Intel 686-class, 1666MHz, id 0x106ca
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <INTEL ,MOPNV10J,000000af>, AslId <    ,01000013>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
LPT (PNP0400) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
APIC (PNP0003) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed03fff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0xa000 (rev. 0x02)
vga0 at pci0 dev 2 function 0: vendor 0x8086 product 0xa001 (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 22
azalia0: host: 0x8086/0x27d8 (rev. 1), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci1 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet
(rev. 0x03)
re0: interrupting at ioapic0 pin 16
re0: Ethernet address 70:71:bc:XX:XX:XX
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x01)
pci2 at ppb1 bus 2
pci2: no spaces enabled!
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x01)
pci3 at ppb2 bus 3
pci3: no spaces enabled!
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x01)
pci4 at ppb3 bus 4
pci4: no spaces enabled!
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x01)
uhci3: interrupting at ioapic0 pin 16
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe1)
pci5 at ppb4 bus 5
pci5: no spaces enabled!
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x27bc (rev. 0x01)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801GB/GR Serial ATA/Raid Controller (ICH7) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 19 for native-PCI interrupt
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[2]: Realtek ALC662-GR (rev. 1.1), HDA rev. 1.0
audio0 at azalia0: full duplex, playback, capture, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: Peppercon AG Multidevice, rev 2.00/0.01, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1wd0 at atabus0
drive 0: <ST3250318AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors

uhidev1: Peppercon AG Multidevice, rev 2.00/0.01, addr 2, iclass 3/0
ums0 at uhidev1: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
umass0 at uhub1 port 1 configuration 1 interface 2
umass0: Peppercon AG Multidevice, rev 2.00/0.01, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
cd0 at scsibus0 target 0 lun 0: <PepperC, Virtual Disc 1, 0.01> cdrom removable
atapibus0 at atabus1: 2 targets
cd1 at atapibus0 drive 0: <HL-DT-ST DVDRAM GH22NS50, K18A74E4534,
TN02> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd1(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
/: replaying log to memory
root file system type: ffs
/: replaying log to disk
/var: replaying log to disk
/usr: replaying log to disk
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
/export: replaying log to disk

-- 
Joern Clausen
http://thebloeg.blogspot.com/
http://www.oe-files.de/oefiles/
Follow-Ups:
- Re: lockup of Atom 330 machine?
  - From: Aleksey Cheusov
Prev by Date: Re: No luck with wi-fi on x86_64
Next by Date: Re: lockup of Atom 330 machine?
Previous by Thread: No luck with wi-fi on x86_64
Next by Thread: Re: lockup of Atom 330 machine?
Indexes:
Home | Main Index | Thread Index | Old Index