A3000 problems

[RadosÅaw Kujawa <radoslaw.kujawa%c0ff33.net@localhost>]

Hi guys,
My A1200 refuses to start again and temporarily A3000 is my test machine.

Some observed problems:

1.Turbo board is not identified properly (as CyberStorm PPC). Again, 
amigappc_identify() is at fault - this CSPPC's serial number starts with 'DD'. 
2. Kernel does not boot with ZorRAM RAM expansion installed. Do we support 
Zorro III RAM expansions at all in amigappc port?
3. Kernel does not boot with Deneb USB card installed, even when flash ROM is 
disabled and Poseidon USB stack unloaded. 
4. Serial port does transmit only in one way (same symptoms as earlier). I have 
machdep.c rev 1.47 with recent Frank's changes.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.41 (GENERICSERIAL) #0: Sun Dec 26 19:09:05 CET 2010
        
rkujawa%Radoslaw-Kujawas-MacBook-Pro.local@localhost:/Users/rkujawa/repos/NetBSD-current/src/sys/arch/amigappc/compile/obj/GENERICSERIAL
Model: Amiga 3000 [PowerUP] (604e v2.4 233 MHz, busclk 66 MHz, ... tbr1 
34795170, tbr2 34795489)
total memory = 127 MB
avail memory = 119 MB
mainbus0 (root)
cpu0 at mainbus0: 604e (Revision 2.4), ID 0 (primary)
cpu0: HID0 0xc084<ICE,DCE,SGE,BHT>, powersave: 1
cpu0: 233.33 MHz
a34kbbc0 at mainbus0
ser0 at mainbus0: input fifo 512 output fifo 32
par0 at mainbus0
kbd0 at mainbus0: CIA A type Amiga
ms0 at mainbus0
grfcc0 at mainbus0
grf0 at grfcc0: width 640 height 400 colors 4
ite0 at grf0: rows 0 cols 0 repeat at (30/100)s next at (10/100)s has keyboard
fdc0 at mainbus0: dmabuf pa 0x1e46bc: dmabuf ka 0x1e46bc
fd0 at fdc0 unit 0: 3.5dd 80 cyl, 2 head, 11 sec [9 sec], 512 bytes/sec
ahsc0 at mainbus0
scsibus0 at ahsc0: 8 targets, 8 luns per target
aucc0 at mainbus0
audio0 at aucc0: half duplex, playback, capture
zbus0 at mainbus0
grfcv3d0 at zbus0 pa 0x40000000 man/pro 8512/67
grf7 at grfcv3d0: width 640 height 480 colors 16
ite7 at grf7: rows 60 cols 80 repeat at (30/100)s next at (10/100)s has keyboard
grfcv3d0: CyberVision64/3D with 4MB being used
board at zbus0: pa 0x50000000 man/pro 2206/62 not configured
cbiiisc0 at zbus0 pa 0xf01060 man/pro 8512/100
cbiiisc0:  no SCSI termination, host adapter deactivated.
scsibus1 at cbiiisc0: 0 targets, 8 luns per target
biomask 800001e netmask 800001e ttymask 800001e
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
4 views configured
root device: 

--
Best regards,
RadosÅaw Kujawa