Port-arm archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Genesi EFIKA MX Linux boot messages.
Just got a Genesi EFIKA MX SmartTop. Here are its boot messages. Now to get
some free time to port NetBSD to it.
U-Boot 2009.01-1.2.19-lange51 (May 06 2010 - 11:52:45)
CPU: Freescale i.MX51 family 3.0V at 800 MHz
mx51 pll1: 800MHz
mx51 pll2: 665MHz
mx51 pll3: 216MHz
ipg clock : 66500000Hz
ipg per clock : 665000000Hz
uart clock : 66500000Hz
cspi clock : 54000000Hz
Board: MX51 LANGE51 3.0 [POR]
DRAM: 512 MB
JEDEC ID: 0xbf:0x25:0x4a
Reading SPI NOR flash 0x40000 [0x10000 bytes] -> ram 0x975f06e8
.SUCCESS
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
board id: 1.0.1, rev1.3
Boot Source: SPI NOR FLASH BOOT
** Unable to use mmc 0:1 for fatload **
Bus 0: OK
Device 0: Model: SanDisk pSSD-P2 8GB Firm: SSD 5.20 Ser#: AFZ071410204649
Type: Hard Disk
Capacity: 7641.2 MB = 7.4 GB (15649200 x 512)
reading system.conf
** Unable to read "system.conf" from ide 0:1 **
Boot Cmd: run pata_boot
Hit any key to stop autoboot: 0
## Error: "base_cmd99" not defined
Reset IDE: Bus 0: OK
Device 0: Model: SanDisk pSSD-P2 8GB Firm: SSD 5.20 Ser#: AFZ071410204649
Type: Hard Disk
Capacity: 7641.2 MB = 7.4 GB (15649200 x 512)
reading uImage
## Booting kernel from Legacy Image at 90007fc0 ...
Image Name: Linux-2.6.31.14-efikamx
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2658376 Bytes = 2.5 MB
Load Address: 90008000
Entry Point: 90008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux.................................................................................................................................................................
done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1
(Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 105664
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200
console=tty1 root=/dev/sda2 rw
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K
highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console handover: boot [ttymxc0] -> real [tty1]
[ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1
(Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 105664
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200
console=tty1 root=/dev/sda2 rw
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K
highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console handover: boot [ttymxc0] -> real [tty1]
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] tmpfs: No value for mount option 'mode'
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] Efika MX: IOMUX for Board ID (3 pins)
[ 0.000000] Efika MX: IOMUX for General GPIO Stuff (7 pins)
[ 0.000000] Efika MX: IOMUX for SPI (6 pins)
[ 0.000000] Efika MX: IOMUX for PMIC (1 pins)
[ 0.000000] Efika MX: IOMUX for I2C (4 pins)
[ 0.000000] Efika MX: IOMUX for USB (29 pins)
[ 0.000000] Efika MX: IOMUX for ATA (29 pins)
[ 0.000000] Efika MX: Initializing SD card IOMUX (external, mmc0)
[ 0.000000] Efika MX: IOMUX for WDOG (1.2) (1 pins)
[ 0.000000] Efika MX: IOMUX for LED (3 pins)
[ 0.000000] Efika MX: IOMUX for Power Key (1 pins)
[ 0.000000] Efika MX: AIPS1_BASE_ADDR = 0x73f00000
[ 0.000000] Efika MX: AIPS1_BASE_ADDR_VIRT = 0xf7e00000, io_pg_offst = 0x3df8
[ 0.000000] Efika MX: PHYS_OFFSET = 0x90000000
[ 0.000000] Efika MX Revision 1.3
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] usbcore: registered new interface driver usbfs
[ 0.000000] usbcore: registered new interface driver hub
[ 0.000000] usbcore: registered new device driver usb
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 1800 <--> 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 0.000000] NET: Registered protocol family 2
[ 0.000000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.535895] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.536484] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.536786] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.536816] TCP reno registered
[ 0.537010] NET: Registered protocol family 1
[ 0.537858] LPMode driver module loaded
[ 0.537891] Static Power Management for Freescale i.MX51
[ 0.538173] PM driver module loaded
[ 0.538428] sdram autogating driver module loaded
[ 0.538733] Bus freq driver module loaded
[ 0.538791] mxc_dvfs_core_probe
[ 0.539053] DVFS driver module loaded
[ 0.539086] i.MXC CPU frequency driver
[ 0.539614] DVFS PER driver module loaded
[ 0.541283] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.541351] msgmni has been set to 814
[ 0.545380] alg: No test for stdrng (krng)
[ 0.545741] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
252)
[ 0.545786] io scheduler noop registered (default)
[ 0.545823] io scheduler cfq registered
[ 0.546325] *** sii9022_probe
[ 0.548616] SII9022 sink not found ! id=00
[ 0.564697] mxcfb_read_edid2
[ 0.565071] read_edid error!
[ 0.565271] *** mxc_init_fb vmode= video-mode=1 clock_auto=1
[ 0.565296] registering framebuffer for HDMI
[ 0.566359] mode_option=800x600-16@60
[ 0.567131] mxc_ipu mxc_ipu: Channel already disabled 9
[ 0.567142] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 0.567159] mxcfb_di_clock_adjust pixelclk=25000 rate=80000000
[ 0.567211] orig: parent=pll3 clk=216000000 this=ipu_di0_clk di_clk=27000000
[ 0.567335] adjust: parent=pll3 clk=80000000 this=ipu_di0_clk
di_clk=40000000 ret=0 ret=0
[ 0.567446] skip sii9022_reinit!
[ 0.567476] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.734691] pclk 25000 same to previous one, skipping!
[ 0.734701] skip sii9022_reinit!
[ 0.734720] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.759149] Console: switching to colour frame buffer device 100x37
[ 0.904681] pclk 25000 same to previous one, skipping!
[ 0.904689] skip sii9022_reinit!
[ 0.904706] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.944689] registering framebuffer for VPU overlay
[ 0.947264] mxc_sdc_fb mxc_sdc_fb.2: Unable to allocate framebuffer memory
[ 0.949552] mxc_sdc_fb: probe of mxc_sdc_fb.2 failed with error -12
[ 0.951790] *** sii9022 lcd_probe
[ 0.954001] *** sii9022 lcd_init_fb
[ 0.974660] mxcfb_read_edid2
[ 0.977228] read_edid error!
[ 0.979595] mxcfb_update_default_var mode_opt=<NULL> vmode=
[ 0.981846] mxcfb_di_clock_adjust pixelclk=13468 rate=148500000
[ 0.984120] orig: parent=pll3 clk=80000000 this=ipu_di0_clk di_clk=40000000
[ 0.986515] adjust: parent=pll3 clk=148500000 this=ipu_di0_clk
di_clk=74250000 ret=0 ret=0
[ 0.988882] sii9022_reinit 1280x720 13468
[ 1.128684] sii9022 1-0039: geometry 1280 720 1280 720 0
[ 1.130974] sii9022 1-0039: timings 13468 220 110 20 5 40 5
[ 1.133235] sii9022 1-0039: accel 0 sync 23 vmode=0
[ 1.135515] sii9022 1-0039: pclk 7425 refresh 6024 total x 1650 y 750
[ 1.137812] sii9022 1-0039: vmap idx=6 vcode=4
[ 1.140483] hdmi audio mute
[ 1.150893] hdmi audio unmute
[ 1.294683] pclk 13468 same to previous one, skipping!
[ 1.294694] sii9022_reinit 1280x720 13468 same to previous one, skipping
[ 1.314691] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 1.331720] sii9022 1-0039: turning on LCD
[ 1.614608] Serial: MXC Internal UART driver
[ 1.615087] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a
Freescale i.MX
[ 1.615272] console [ttymxc0] enabled
[ 2.770387] mxcintuart.1: ttymxc1 at MMIO 0x73fc0000 (irq = 32) is a
Freescale i.MX
[ 2.782998] mxcintuart.2: ttymxc2 at MMIO 0x7000c000 (irq = 33) is a
Freescale i.MX
[ 2.799586] loop: module loaded
[ 2.807826] pata_fsl pata_fsl: rchan=29 wchan=28
[ 2.816489] scsi0 : pata_fsl
[ 2.823544] ata1: PATA max UDMA/44 irq 70
[ 2.833402] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.944683] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 2.955627] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number
1
[ 2.994697] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 3.007963] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133
[ 3.018240] ata1.00: 15649200 sectors, multi 0: LBA48
[ 3.027371] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.037484] usb usb1: configuration #1 chosen from 1 choice
[ 3.047605] hub 1-0:1.0: USB hub found
[ 3.054971] hub 1-0:1.0: 1 port detected
[ 3.070837] ata1.00: configured for UDMA/44
[ 3.094998] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD
PQ: 0 ANSI: 5
[ 3.107744] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01
GB/7.46 GiB)
[ 3.119309] sd 0:0:0:0: [sda] Write Protect is off
[ 3.127852] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 3.141196] sda: sda1 sda2
[ 3.149537] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.160637] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.274690] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 3.285493] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 3.296734] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number
2
[ 3.334692] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 3.444664] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 3.454890] usb usb2: configuration #1 chosen from 1 choice
[ 3.464835] hub 2-0:1.0: USB hub found
[ 3.472401] hub 2-0:1.0: 1 port detected
[ 3.480779] usbcore: registered new interface driver libusual
[ 3.491690] mice: PS/2 mouse device common for all mice
[ 3.501238] MXC keypad loaded
[ 3.508794] mc13892 rtc probe start
[ 3.517019] usb 1-1: configuration #1 chosen from 1 choice
[ 3.527412] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 3.538004] mc13892 rtc probe succeed
[ 3.545850] i2c /dev entries driver
[ 3.554412] Linux video capture interface: v2.00
[ 3.564262] MXC Video Output MXC Video Output.0: Registered device video0
[ 3.575033] MXC WatchDog Driver 2.0
[ 3.582361] clk: Unable to get requested clock: wdog_clk
[ 3.592067] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 3.601709] cpuidle: using governor ladder
[ 3.609605] cpuidle: using governor menu
[ 3.617916] PMIC Character device: successfully loaded
[ 3.627694] VPU initialized
[ 3.634512] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 3.645040] mxsdhci: MXC SDHCI Controller Driver.
[ 3.653785] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 3.663401] Registered led device: efikamx:green
[ 3.671780] Registered led device: efikamx:red
[ 3.690174] Registered led device: efikamx:blue
[ 3.702707] usbcore: registered new interface driver usbhid
[ 3.711937] usbhid: v2.6:USB HID core driver
[ 3.743235] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 3.775405] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 3.804692] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 3.816973] No device for DAI imx-ssi-1-0
[ 3.824777] No device for DAI imx-ssi-1-1
[ 3.832412] No device for DAI imx-ssi-2-0
[ 3.839958] No device for DAI imx-ssi-2-1
[ 3.848301] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1fff6000
buf->area=9a856000 size=24576
[ 3.860985] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8318000
buf->area=f9e30000 size=24576
[ 3.873392] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 3.927067] ALSA device list:
[ 3.933504] #0: imx-3stack (SGTL5000)
[ 3.941637] TCP cubic registered
[ 3.948156] NET: Registered protocol family 17
[ 3.955789] ThumbEE CPU extension supported.
[ 3.963263] VFP support v0.3: implementor 41 architecture 3 part 30 variant
c rev 2
[ 3.976417] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 3.987136] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 3.997581] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 4.007823] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 4.018170] regulator_init_complete: incomplete constraints, leaving VGEN3 on
[ 4.028518] regulator_init_complete: incomplete constraints, leaving VGEN2 on
[ 4.038755] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 4.049051] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 4.059170] regulator_init_complete: incomplete constraints, leaving VAUDIO
on
[ 4.069421] regulator_init_complete: incomplete constraints, leaving VSD on
[ 4.079342] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 4.089583] pmic_rtc pmic_rtc.1: setting system clock to 2010-10-05 23:15:33
UTC (1286320533)
[ 4.106235] usb 2-1: configuration #1 chosen from 1 choice
[ 4.115485] hub 2-1:1.0: USB hub found
[ 4.122445] EXT3-fs: sda2: couldn't mount because of unsupported optional
features (240).
[ 4.133891] hub 2-1:1.0: 4 ports detected
[ 4.142148] EXT2-fs: sda2: couldn't mount because of unsupported optional
features (240).
[ 4.193836] EXT4-fs (sda2): barriers enabled
[ 4.214910] kjournald2 starting: pid 1021, dev sda2:8, commit interval 5
seconds
[ 4.227682] EXT4-fs (sda2): internal journal on sda2:8
[ 4.236106] EXT4-fs (sda2): delayed allocation enabled
[ 4.244398] EXT4-fs: file extents enabled
[ 4.253137] EXT4-fs: mballoc enabled
[ 4.259840] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 4.269496] VFS: Mounted root (ext4 filesystem) on device 8:2.
[ 4.331708] devtmpfs: mounted
[ 4.338258] Freeing init memory: 140K
[ 4.455000] usb 2-1.1: new high speed USB device using fsl-ehci and address 3
[ 4.595108] usb 2-1.1: configuration #1 chosen from 1 choice
[ 10.477939] eth0: link down
[ 10.574865] usb 2-1.1: firmware: requesting rt3070.bin
[ 13.076259] 0x1300 = 00073200
Ubuntu maverick (development branch) efikamx ttymxc0
efikamx login: [ 15.396167] 0x1300 = 00073200
[ 15.769147] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
dm-devel%redhat.com@localhost
[ 17.424705] pclk 13468 same to previous one, skipping!
[ 17.424726] sii9022_reinit 1280x720 13468 same to previous one, skipping
[ 17.444758] *** sii9022 lcd_fb_event
[ 17.574674] *** sii9022 lcd_fb_event
[ 17.574688] sii9022 1-0039: turning off LCD
[ 18.209967] mxc_ipu mxc_ipu: Channel already disabled 9
[ 18.209983] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 18.209998] pclk 13468 same to previous one, skipping!
[ 18.210009] sii9022_reinit 1280x720 13468 same to previous one, skipping
[ 18.224792] *** sii9022 lcd_fb_event
[ 18.224802] sii9022 1-0039: turning on LCD
[ 24.430560] ata1.00: configured for UDMA/44
[ 24.434865] ata1: EH complete
Home |
Main Index |
Thread Index |
Old Index