[guruplug] mvgbe1 no PHY found

[Freddy DISSAUX <freddy.dsx%free.fr@localhost>]

Hi,


If someone have idea/patch for the 'mvgbe1: no PHY found!' ...

kernel config come from SHEEVAPLUG without bluetooth.

I just activate debug mode for the driver:

netbsd-001# cvs diff ./sys/dev/marvell/if_mvgbe.c
Index: ./sys/dev/marvell/if_mvgbe.c
===================================================================
RCS file: /pub/NetBSD-CVS/src/sys/dev/marvell/if_mvgbe.c,v
retrieving revision 1.5
diff -r1.5 if_mvgbe.c
63c63
< /* #define MVGBE_DEBUG 3 */
---
> #define MVGBE_DEBUG 3



NetBSD/evbarm (sheevaplug) booting ...
Loaded initial symtab at 0xc0254fec, strtab at 0xc027cff4, # entries
10158
pmap_postinit: Allocated 35 static L1 descriptor tables
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004,
2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.45 (GURUPLUG) #11: Tue Feb  8 19:12:01 CET 2011
        
root%netbsd-001.lncsa.com@localhost:/usr/obj/sys/arch/evbarm/compile/GURUPLUG
total memory = 512 MB
avail memory = 498 MB
sysctl_createv: sysctl_create(no_sa_support) returned 22
mainbus0 (root)
cpu0 at mainbus0: Sheeva 88SV131 rev 1 (ARM9E-S core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C Data cache
mvsoc0 at mainbus0: Marvell 88F6281 Rev. A1  Kirkwood
mvsoc0: CPU Clock 1200.000 MHz  SysClock 400.000 MHz  TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
mvsocgpp at mvsoc0 unit 0 not configured
com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Interface
usb0 at ehci0: USB revision 2.0
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x11fff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
mvcesa at mvsoc0 unit 0 not configured
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet 
Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address 00:50:43:01:85:d4
mvgbe_jumbo_buf = 0xc289f000
mvgbe_stop
makphy0 at mvgbe0 phy 0: Marvell 88E1149 Gigabit PHY, rev. 3
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto 
makphy1 at mvgbe0 phy 1: Marvell 88E1149 Gigabit PHY, rev. 3
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
mvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet 
Controller
mvgbe1 at mvgbec1 port 0 irq 14
mvgbe1: Ethernet address 00:50:43:01:85:d5
mvgbe_jumbo_buf = 0xc2bf8000
mvgbe_stop
mvgbe1: no PHY found!
mvpex at mvsoc0 unit 0 not configured
mvsata at mvsoc0 unit 0 not configured
mvsdio0 at mvsoc0 unit 0 offset 0x90000-0x9ffff irq 28: Marvell Secure Digital 
Input/Output Interface
sdmmc0 at mvsdio0
uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
sdmmc0: bad CIS ptr 0
sdmmc0: couldn't read CIS
sdmmc0: i/o init failed
sdmmc0: bad CIS ptr 0
sdmmc0: couldn't read CIS
sdmmc0: i/o init failed
"Marvell, 802.11 SDIO ID: 10, " (manufacturer 0x2df, product 0x9103) at sdmmc0 
function 1 not configured
"Marvell, 802.11 SDIO ID: 10, " (manufacturer 0x2df, product 0x9103) at sdmmc0 
function 2 not configured
uhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/77.60, 
addr 2
uhub1: single transaction translator
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Genesys Logic USB Storage, rev 2.00/99.09, addr 3
scsibus0 at umass0: 2 targets, 2 luns per target
sd0 at scsibus0 target 0 lun 0: <Generic, STORAGE DEVICE, 9909> disk
removable
sd0: drive offline
sd1 at scsibus0 target 0 lun 1: <Generic, STORAGE DEVICE, 9909> disk
removable