Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012

To: SAITOH Masanobu <msaitoh%execsw.org@localhost>
Subject: Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
From: Andy Ruhl <acruhl%gmail.com@localhost>
Date: Tue, 18 Dec 2012 21:54:12 -0700

On Tue, Dec 18, 2012 at 8:29 AM, Andy Ruhl <acruhl%gmail.com@localhost> wrote:
> On Tue, Dec 18, 2012 at 6:43 AM, SAITOH Masanobu 
> <msaitoh%execsw.org@localhost> wrote:
>>         Boot u-boot
>>
>>         type any key to stop autoboot
>>
>>         got the uboot's prompt "CE>>"
>>
>>         and type printenv<CR>
>>
>> That's all :-)
>
> Ok, I was assuming that everyone was booting NetBSD the same as I am.
> This appears to not be the case.

I have since re-written the original bootloader, and then tried to
boot again. The kernel you gave me boots fine from tftp, but it panics
at init just like before. Something must be different with our
machines.

Here is the log of the entire boot process (sorry about all the
control characters in the NetBSD kernel messages):

U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:1.0

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
CE>> printenv
baudrate=115200
loads_echo=0
ipaddr=169.254.254.253
serverip=169.254.254.254
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
run_diag=yes
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
ethaddr=00:10:75:1A:5E:FE
cesvcid=JK97YJZBJDVCGYKSAFYB5MLK3A
ceserialno=2GEP0PAX
ceboardver=REDSTONE:1.0
bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(boo
targs_root); bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no

Environment size: 762/131068 bytes
CE>> setenv ipaddr 192.168.0.47
CE>> setenv serverip 192.168.0.203
CE>> setenv netmask 255.255.255.0
CE>> setenv bootcmd 'tftpboot 0x2000000 sheeva20121218.ub; bootm'
CE>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
run_diag=yes
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
ethaddr=00:10:75:1A:5E:FE
cesvcid=JK97YJZBJDVCGYKSAFYB5MLK3A
ceserialno=2GEP0PAX
ceboardver=REDSTONE:1.0
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
ipaddr=192.168.0.47
serverip=192.168.0.203
netmask=255.255.255.0
bootcmd=tftpboot 0x2000000 sheeva20121218.ub; bootm

Environment size: 703/131068 bytes
CE>> boot
Using egiga0 device
TFTP from server 192.168.0.203; our IP address is 192.168.0.47
Filename 'sheeva20121218.ub'.
Load address: 0x2000000
Loading: #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #####################################
done
Bytes transferred = 4845504 (49efc0 hex)
## Booting image at 02000000 ...
   Image Name:   NetBSD/sheevaplug 6.99.15
   Created:      2012-12-18  12:09:57 UTC
   Image Type:   ARM NetBSD Kernel Image (uncompressed)
   Data Size:    4845440 Bytes =  4.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00008000) ...

NetBSD/evbarm (sheevaplug) booting ...
^[[38CUSPACE_SVC 1df0
^[[15CKSTACK_SIZE 1df0
^[[16C[ Kernel symbol table missing! ]
^[[32CLoaded initial symtab at 0xc03d9698, strtab at 0xc0413514, # entries 14741
^[[74Cpmap_postinit: Allocated 35 static L1 descriptor tables
^[[55CCopyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
^[[73C    2006, 2007, 2008, 2009, 2010, 2011, 2012
^[[44C    The NetBSD Foundation, Inc.  All rights reserved.
^[[53CCopyright (c) 1982, 1986, 1989, 1991, 1993
^[[42C    The Regents of the University of California.  All rights reserved.
^[[70C
NetBSD 6.99.15 (SHEEVAPLUG) #0: Tue Dec 18 21:09:56 JST 2012
^[[60C^[[8Cmsaitoh%tap.execsw.org@localhost:/var/sources/NetBSD-current/src/sys/arch/evbar
m/compile/SHEEVAPLUG
^[[17Ctotal memory = 128 MB
^[[21Cavail memory = 120 MB
^[[21Ccprng kernel: WARNING insufficient entropy at creation.
^[[55Cmainbus0 (root)
^[[15Ccpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S core)
^[[60Ccpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
^[[69Ccpu0: 16KB/32B 4-way L1 Instruction cache
^[[41Ccpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
^[[55Cmvsoc0 at mainbus0: Marvell 88F6281 Rev. A0  Kirkwood
^[[53Cmvsoc0: CPU Clock 1200.000 MHz  SysClock 400.000 MHz  TClock 200.000 MHz
^[[72Cmvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
^[[68Cmvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC Gene
ral Purpose I/O Port Interface
^[[24Cmvsocgpp0: 50 gpio pins
^[[23Cmvsocgpp0: interrupts 96..103, intr 35
^[[38Cmvsocgpp0: interrupts 104..111, intr 36
^[[39Cmvsocgpp0: interrupts 112..119, intr 37
^[[39Cmvsocgpp0: interrupts 120..127, intr 38
^[[39Cmvsocgpp0: interrupts 128..135, intr 39
^[[39Cmvsocgpp0: interrupts 136..143, intr 40
^[[39Cmvsocgpp0: interrupts 144..151, intr 41
^[[39Cmvsocgpp0:   Data Out:                  0xeff00000
^[[50Cmvsocgpp0:   Data Out Enable Control:   0xefffffff
^[[50Cmvsocgpp0:   Data Blink Enable:         0x00000000
^[[50Cmvsocgpp0:   Data In Polarity:          0x00000000
^[[50Cmvsocgpp0:   Data In:                   0xeff00080
^[[50Cmvsocgpp0:   Interrupt Cause:           0x00000000
^[[50Cmvsocgpp0:   Interrupt Mask:            0x00000000
^[[50Cmvsocgpp0:   Interrupt Level Mask:      0x00000000
^[[50Cmvsocgpp0:   High Data Out:             0xffffffff
^[[50Cmvsocgpp0:   High Data Out Enable Ctrl: 0xfffc3fff
^[[50Cmvsocgpp0:   High Blink Enable:         0x00004000
^[[50Cmvsocgpp0:   High Data In Polarity:     0x00000000
^[[50Cmvsocgpp0:   High Data In:              0x0003fffd
^[[50Cmvsocgpp0:   High Interrupt Cause:      0x00004000
^[[50Cmvsocgpp0:   High Interrupt Mask:       0x00000000
^[[50Cmvsocgpp0:   High Interrupt Level Mask: 0x00000000
^[[50Cgpio0 at mvsocgpp0: 50 pins
^[[27Cmvsocrtc0 at mvsoc0 unit 0 offset 0x10300-0x10317: Marvell SoC Real Time C
lock
^[[78Ccom0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fif
o
^[[75Ccom0: console
^[[13Ccom1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fif
o
^[[75Cehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Inte
rface
^[[79Cusb0 at ehci0: USB revision 2.0
^[[31Cgtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/
XOR Engine
^[[4Cgtidmac0: XOR Engine 4 channels, intr 5...8
^[[43Cgttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI contr
oller
^[[79Ciic0 at gttwsi0: I2C bus
^[[24Cmvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptograp
hic Engines and Security Accelerator
^[[30Cmvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet
Controller
^[[4Cmvgbe0 at mvgbec0 port 0 irq 11
^[[31Cmvgbe0: Ethernet address 00:10:75:1a:5e:fe
^[[42Cmakphy0 at mvgbe0 phy 0: Marvell 88E1116R Gigabit PHY, rev. 0
^[[61Cmakphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-FDX, auto
^[[7Cmvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet C
ontroller
^[[4Cmvgbe at mvgbec1 port 0 not configured
^[[38Cmvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express
Interface
   pci0 at mvpex0
^[[14Cvendor 0x11ab product 0x6281 (miscellaneous memory, revision 0x02) at pci0
 dev 0 function 0 not configured
^[[26Cmvsoc0: mvsata0 clock disabled
^[[30Cmvsdio0 at mvsoc0 unit 0 offset 0x90000-0x9ffff irq 28: Marvell Secure Dig
ital Input/Output Interface
^[[21Csdmmc0 at mvsdio0
^[[17Cuhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
^[[70Cuhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/6.03,
 addr 2^H
 ^Huhub1: single transaction translator
^[[36Cumass0 at uhub1 port 4 configuration 1 interface 0
^[[50Cumass0: PNY Technologies USB 2.0 FD, rev 2.00/81.92, addr 3
^[[59Cscsibus0 at umass0: 2 targets, 1 lun per target
^[[47Csd0 at scsibus0 target 0 lun 0: <PNY, USB 2.0 FD, 8192> disk removable
^[[70Csd0: 7728 MB, 15744 cyl, 16 head, 63 sec, 512 bytes/sect x 15826944 sector
s
^[[75Ccprng sysctl: WARNING insufficient entropy at creation.
^[[55Cboot device: <unknown>
^[[22Croot device: sd0a
^[[17Cdump device (default sd0b):
^[[28Cfile system (default generic): ffs
^[[34Croot on sd0a dumps on sd0b
^[[26CWARNING: clock lost 4734 days
^[[29CWARNING: using filesystem time
^[[30CWARNING: CHECK AND RESET THE DATE!
^[[34Cwarning: no /dev/console
^[[24Cinit path (default /sbin/init):
^[[32Cinit: copying out path `/sbin/init' 11
^[[38Cdata_abort_handler: data_aborts fsr=0x1 far=0x28207697
^[[54CFatal kernel mode data abort: 'Alignment Fault 1'
^[[49Ctrapframe: 0xc7efcd00
^[[21CFSR=00000001, FAR=28207697, spsr=20000013
^[[41Cr0 =00000004, r1 =00000000, r2 =c207d010, r3 =00000000
^[[54Cr4 =28207665, r5 =00000000, r6 =00000000, r7 =c207d010
^[[54Cr8 =c04c40fc, r9 =00000000, r10=00000000, r11=c7efcd88
^[[54Cr12=00000001, ssp=c7efcd50, slr=c02c5364, pc =c02c53f0
^[[54C
Stopped in pid 2.1 (sh) at      netbsd:uvm_pagealloc_pgfl+0xbc: ldrh    r3, [r4,
^[[79C #0x32]
^[[7Cdb>

Follow-Ups:
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: David Laight

References:
- Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: Andy Ruhl
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: Adam Hoka
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: Martin Husemann
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: Andy Ruhl
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: SAITOH Masanobu
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: Andy Ruhl
- Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
  - From: SAITOH Masanobu

Prev by Date: Re: No response from 2012-10-13-netbsd6.99.12-rasp.zip
Next by Date: Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
Previous by Thread: Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
Next by Thread: Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
Indexes:

Home | Main Index | Thread Index | Old Index