sdhc1: data crc error

[Rui-Xiang Guo <rxg%lavabit.com@localhost>]

Hi,
When trying to boot 10.0 aarch64 on the Google i.MX8MQ Phanbell board
(a.k.a Coral Dev Board), everything looks fine except 'sdhc1: data crc error'.
Here is part of dmesg -
[...]
[   1.0000040] sdhc0 at simplebus4: SDMMC (400000 kHz)
[   1.0000040] sdhc0: interrupting on irq 54
[   1.0000040] sdhc0: SDHC 3.0, rev 0, 32-bit ADMA2, 180000 kHz, HS SDR50 DDR50 1.8V 3.0V 3.3V, re-tuning mode 1, 4096 byte blocks
[   1.0000040] sdmmc0 at sdhc0 slot 0
[   1.0000040] sdhc1 at simplebus4: SDMMC (200000 kHz)
[   1.0000040] sdhc1: interrupting on irq 55
[   1.0000040] sdhc1: SDHC 3.0, rev 0, 32-bit ADMA2, 180000 kHz, HS SDR50 DDR50 1.8V 3.0V 3.3V, re-tuning mode 1, 4096 byte blocks
[   1.0000040] sdmmc1 at sdhc1 slot 0
[   1.0000040] /soc@0/bus@32c00000/interrupt-controller@32e2d000 at simplebus6 not configured
[   1.0000040] xhci0 at simplebus1: cannot switch 'otg' mode to host
[   1.0000040] xhci1 at simplebus1: DesignWare USB3 XHCI (rev. 3.10a)
[   1.0000040] xhci1: interrupting on irq 73
[   1.0000040] usb0 at xhci1: USB revision 3.0
[   1.0000040] usb1 at xhci1: USB revision 2.0
[   1.0000040] /soc@0/video-codec@38300000 at simplebus1 not configured
[   1.0000040] armpmu0 at simplebus0: Performance Monitor Unit
[   1.0000040] /soc@0/ddr-pmu@3d800000 at simplebus1 not configured
[   1.8387029] cpufreqdt0: couldn't acquire cpu-supply
[   1.8387029] cpufreqdt1: couldn't acquire cpu-supply
[   1.8487055] cpufreqdt2: couldn't acquire cpu-supply
[   1.8487055] cpufreqdt3: couldn't acquire cpu-supply
[   1.8587035] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
[   1.8687052] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
[   1.8887044] armpmu0: interrupting on GICv3 irq 23
[   1.8887044] WARNING: system needs entropy for security; see entropy(7)
[   2.0487077] sdmmc1: SD card status: 4-bit, C10, U1, V10
[   2.0487077] ld1 at sdmmc1: <0x9f:0x5449:00000:0x00:0x00000384:0x12c>
[   2.0587075] ld1: 30168 MB, 7661 cyl, 128 head, 63 sec, 512 bytes/sect x 61784064 sectors
[   2.0698407] dk0 at ld1: "EFI", 163840 blocks at 32768, type: msdos
[   2.0698407] dk1 at ld1: "netbsd-root", 2891776 blocks at 196608, type: ffs
[   2.0857484] ld1: 4-bit width, DDR50, 50.000 MHz
[   2.0904707] swwdog0: software watchdog initialized
[   2.1004707] WARNING: 6 errors while detecting hardware; check system log.
[   2.1004707] boot device: dk1
[   2.1104702] root on dk1
[   2.1204705] root file system type: ffs
[   2.1204705] kern.module.path=/stand/evbarm/10.0/modules
[   2.1304705] WARNING: no TOD clock present
[   2.1304705] WARNING: using filesystem time
[   2.1391266] WARNING: CHECK AND RESET THE DATE!
[   2.1404710] sdhc1: data crc error
[   7.0305622] entropy: best effort
[  12.1406582] ld1c: error reading fsbn 280880 of 280880-280959 (ld1 bn 280880; cn 34 tn 106 sn 26), retrying
[  12.6406669] sdhc1: data crc error
[  22.6408544] ld1c: error reading fsbn 280880 of 280880-280959 (ld1 bn 280880; cn 34 tn 106 sn 26), retrying
[  23.1408637] sdhc1: data crc error
[  33.1410512] ld1c: error reading fsbn 280880 of 280880-280959 (ld1 bn 280880; cn 34 tn 106 sn 26), retrying

This card is definitely good because it is used to boot the RIoTboard.

-rxg