Qube2700

[Izumi Tsutsui <tsutsui%ceres.dti.ne.jp@localhost>]

I've got Qube2700 today, and it seems just working though
there is something wrong around bootloader even on wd boot.

I'll try to setup zs serial on 2700 later.

---
# dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.54 (INSTALL) #8: Fri Feb 29 00:05:44 JST 2008
        tsutsui@mirage:/usr/src/sys/arch/cobalt/compile/INSTALL
Cobalt Qube 2700
total memory = 16384 KB
avail memory = 14080 KB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
cpu0 at mainbus0: QED RM5200 CPU (0x2810) Rev. 1.0 with built-in FPU Rev. 1.0
cpu0: 16KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 16KB/32B 2-way set-associative write-back L1 Data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64011 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21041 Ethernet, pass 2.1
tlp0: interrupting at level 2
tlp0: Ethernet address 00:10:e0:00:09:46
tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
tlp0: WARNING: powerhook_establish is deprecated
pcib0 at pci0 dev 9 function 0
pcib0: vendor 0x1106 product 0x0586, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
vendor 0x1106 product 0x3038 (USB serial bus, revision 0x02) at pci0 dev 9 
function 2 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 75000000 Hz quality 100
wd0 at atabus0 drive 0: <ST380021A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: tlp0
root on tlp0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 192.168.20.1
nfs_boot: my_domain=ceres.dti.ne.jp
nfs_boot: my_addr=192.168.20.38
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.20.1
root on mirage:/nfsroot
# sysctl hw.model
hw.model = Cobalt Qube 2700
# vmstat -i
interrupt                                     total     rate
softint net/0                                 13653       17
softint bio/0                                    56        0
softint clk/0                                 21759       27
softint ser/0                                     1        0
cpu int 2                                     24552       31
icu irq 14                                       76        0
mips int 5 (clock)                            79117      101
Total                                        139214      178

# 
---
Izumi Tsutsui