Re: Firewire/USB Card for Qube 2

[Izumi Tsutsui <tsutsui%ceres.dti.ne.jp@localhost>]

> I was going to get myself one of those PCI combo cards to *finally*  
> hook up some external drives to my Qube2. The one I have in mind  
> right now:
> 
>    http://tinyurl.com/6c2oz6
> 
> It's based on VIA controllers, VT6306 for Firewire-400 and VT6214 for  
> USB 2.0, and I've seen a bunch of dmesg dumps around that indicate  
> these are supported by NetBSD.

At least VT8237 (actually VT6212L) USB seems to work on my Qube2700.
(though not heavily tested)
VT6306 Firewire is also probed, but I don't have any devices to test it.

Note it looks my card (combo with USB, Firewire and Gig-Ethernet)
consumes too much power and it won't work with an internal IDE disk.
(my qube gets reset right after the devices are probed or initialized)

Furthermore, GENERIC doesn't have those devices so you have to
compile your own custom kernel.

---
NetBSD 4.99.63 (PCIDEVS) #6: Sat May 17 21:22:30 JST 2008
        tsutsui@mirage:/usr/src/sys/arch/cobalt/compile/PCIDEVS
Cobalt Qube 2700
total memory = 65536 KB
avail memory = 55876 KB
mainbus0 (root)
cpu0: 16KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 16KB/32B 2-way set-associative write-back L1 Data cache
zsc0 at mainbus0 addr 0x1c800000 irq 4: optional Z85C30 serial port
zstty0 at zsc0 channel 0 (console i/o)
zstty1 at zsc0 channel 1
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64011 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21041 Ethernet, pass 2.1
tlp0: interrupting at level 2
tlp0: Ethernet address 00:10:e0:00:09:46
tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
uhci0 at pci0 dev 9 function 2: VIA Technologies VT83C572 USB Controller (rev. 
0x02)
uhci0: can't map i/o space
uhci1 at pci0 dev 10 function 0: VIA Technologies VT83C572 USB Controller (rev. 
0x61)
uhci1: interrupting at irq 9
usb0 at uhci1: USB revision 1.0
uhci2 at pci0 dev 10 function 1: VIA Technologies VT83C572 USB Controller (rev. 
0x61)
uhci2: interrupting at irq 9
usb1 at uhci2: USB revision 1.0
ehci0 at pci0 dev 10 function 2: VIA Technologies VT8237 EHCI USB Controller 
(rev. 0x63)
ehci0: interrupting at irq 9
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci1 uhci2
usb2 at ehci0: USB revision 2.0
fwohci0 at pci0 dev 10 function 3: VIA Technologies VT6306 IEEE 1394 Host 
Controller (rev. 0x46)
fwohci0: interrupting at irq 9
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:01:08:00:37:02:79:4f
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 1024 bytes.
fwohci0: max_rec 1024 -> 2048
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vge0 at pci0 dev 10 function 4: VIA VT612X Gigabit Ethernet (rev. 0x11)
vge0: interrupting at irq 9
vge0: Ethernet address: 00:01:08:00:b1:71
ciphy0 at vge0 phy 1: Cicada CS8201 10/100/1000TX PHY, rev. 2
ciphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 75000000 Hz quality 100
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
uhub0 at usb0: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: VIA Technologies EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
Kernelized RAIDframe activated
boot device: tlp0
root on tlp0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 192.168.20.1
nfs_boot: my_domain=ceres.dti.ne.jp
nfs_boot: my_addr=192.168.20.38
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.20.1
root on mirage:/nfsroot
root file system type: nfs

 :

umass0 at uhub2 port 2 configuration 1 interface 0
umass0: BUFFALO ClipDrive, rev 2.00/2.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <BUFFALO, ClipDrive, 2.00> disk removable
sd0: fabricating a geometry
sd0: 250 MB, 250 cyl, 64 head, 32 sec, 512 bytes/sect x 512000 sectors
sd0: fabricating a geometry
sd0: no disk label

 :

# fsck_msdos -fn /dev/rsd0e
** /dev/rsd0e
** Phase 1 - Read and Compare FATs
** Phase 2 - Check Cluster Chains
** Phase 3 - Checking Directories
** Phase 4 - Checking for Lost Files
135 files, 87212 free (21803 clusters)
# 
---
Izumi Tsutsui