There's been alot of discussion about disklabels, but noone has
mentiond how to label the disk when the system says that it is not 
configured.  When I do a "disklabel -r sd0", I get 
"disklabel: /dev/rsd0d: Device not configured".  The disk
(and 3 others) are seen at boot time, as can be seen below (they are
sd0, sd1, sd2, and sd3).

Any suggestions about what to do?

(I had labels on them, but they just "disappered" for no 
apparent reason.  I never had a file system on them since I
access them using raw I/O.)

Liddy

NetBSD 1.3F (rumba) #64: Mon Jul 27 10:40:41 PDT 1998
    shriver@rumba:/usr/src/sys/arch/i386/compile/rumba
cpu0: family 5 model 2 step b
cpu0: Intel Pentium (P54C) (586-class)
real mem  = 49938432
avail mem = 43819008
using 635 buffers containing 2600960 bytes of memory
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o enabled, memory enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82437FX System Controller (TSC) (rev. 0x02)
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371FB PCI-to-ISA Bridge (PIIX) (rev. 0x02)
Intel 82371FB IDE controller (PIIX) (IDE mass storage, interface 0x80, revision 
0x02) at pci0 dev 7 function 1 not configured
de0 at pci0 dev 17 function 0
de0: interrupting at irq 10
de0: Asante 21140 [10-100Mb/s] pass 1.1
de0: address 00:00:94:75:32:8b
ahc0 at pci0 dev 18 function 0
ahc0: interrupting at irq 9
ahc0: aic7880 Wide Channel, SCSI Id=7, 16 SCBs
scsibus0 at ahc0 channel 0: 16 targets
ahc0: target 0 using 16Bit transfers
ahc0: target 0 synchronous at 10.0MHz, offset = 0x8
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST34501W, 0015> SCSI2 0/direct fixed
sd0: 4339MB, 6576 cyl, 8 head, 168 sec, 512 bytes/sect x 8887200 sectors
ahc0: target 1 using 16Bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
sd1 at scsibus0 targ 1 lun 0: <SEAGATE, ST34501W, 0015> SCSI2 0/direct fixed
sd1: 4339MB, 6576 cyl, 8 head, 168 sec, 512 bytes/sect x 8887200 sectors
ahc0: target 2 using 16Bit transfers
ahc0: target 2 synchronous at 10.0MHz, offset = 0x8
sd2 at scsibus0 targ 2 lun 0: <SEAGATE, ST34501W, 0015> SCSI2 0/direct fixed
sd2: 4334MB, 6576 cyl, 8 head, 168 sec, 512 bytes/sect x 8876824 sectors
ahc0: target 3 using 16Bit transfers
ahc0: target 3 synchronous at 10.0MHz, offset = 0x8
sd3 at scsibus0 targ 3 lun 0: <SEAGATE, ST34501W, 0015> SCSI2 0/direct fixed
sd3: 4334MB, 6576 cyl, 8 head, 168 sec, 512 bytes/sect x 8876824 sectors
S3 Trio32/64 (VGA display, revision 0x43) at pci0 dev 19 function 0 not configur
ed
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atapibus0 at wdc0
wd0 at wdc0 drive 0: <ST33232A>
wd0: using 16-sector 16-bit pio transfers, lba mode
wd0: 3077MB, 6303024 sec, 512 bytes/sec
wd1 at wdc0 drive 1: <WDC AC31200F>
wd1: using 16-sector 16-bit pio transfers, lba mode
wd1: 1222MB, 2503872 sec, 512 bytes/sec
wdc1 at isa0 port 0x170-0x177 irq 15
atapibus1 at wdc1
fe_simple_probe: ff & 70 != 0
ate_match: ate_find failed
fe_simple_probe: ff & 70 != 0
fmv_match: fmv_find failed
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
pc0 at isa0 port 0x60-0x6f irq 1: color
pc0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
biomask c240 netmask c640 ttymask c6c2
WARNING: old BSD partition ID!
wd1: no disk label
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
de0: enabling 10baseT port